Fix the following race condition,
1. A connection request to driver which requires DBS
2. DBS gets granted, but connection fails, so opportunistic timer
starts off
3. New connection request gets queued in SME & opportunistic timer fires
and SMM HW mode request gets queued behind the connection request
4. Connection is succesful which needs DBS
5. SMM hw mode request gets sent to FW
Change-Id: I0456eba8165015b58b341df934fbfad5fb6eee86
CRs-Fixed: 2186292
It is decided to centralize the logic of programming LI based on
modulated/dynamic DTIM in FW to address the concerns with LFR3.0 in WoW
mode. In order to make it work, following steps need to be performed.
1) If listen interval offload bit is enabled in service ready extension
then,
a) Driver needs to send "gEnableModulatedDTIM", "gMaxLIModulatedDTIM"
and "gEnableDynamicDTIM" params' value to FW via VDEV PARAM up on
each successful association.
b) Driver should not program LI during suspend()/resume()
2) If listen interval offload bit is disabled in service ready extension
then don't trigger above changes.
Change-Id: I6f94c95bd83e5846d7290d5dc752b14da5951a76
CRs-Fixed: 2187597
Reduce the minimum value for the ini nr_offload_cache_timeout to
5 seconds.
This is done to give the user a shorter cache_timeout to trigger
neighbor report frames more frequently.
Change-Id: Ica5359b9e826dad382868de991dcbf204c10a096
CRs-Fixed: 2189034
Size allocate with sizeof(target_paddr_t) which is following DMA
device, but free with sizeof(qdf_nbuf_t) which is a pointer following
system. Maybe not same size on some platform.
Fix it by using same type when allocate/free.
Change-Id: Iadcb68b05ca5798f38c4341323b9fd1e32f5d693
CRs-Fixed: 2189671
Check the current vdev supported bandwidth values agianst peer
opemode update value and if the peer opmode value is greater than
current supported value then do not send the opmode update request
to FW.
Change-Id: I8f360d769b5aafb90061a6a9d18f1f8062e3534e
CRs-Fixed: 2174050
Update the HE STBC capabilty per latest spec and add support
to configure it using INI configuration and ioctl.
Change-Id: I4ecc7b600671c132c1f3968a10fb652a4311f484
CRs-Fixed: 2181114
Stats events are sent by WLAN FW based on over the air frame reception
and may contain incorrect vdev id hence sanitize vdev id received from
FW in stats events before accessing interface array based on it.
Change-Id: I4ecc73fc27285c98c0ea8cebc27955213cd68399
CRs-Fixed: 2186953
Before VDEV_STOP is initiated by host, sometimes there are
outstanding mgmt tx pkts left in FW. need wait all tx
complete, or peer vdev ref count keep held. In P2P GO/SAP mode,
no wait since wma->interfaces[session_id].delay_before_vdev_stop
is 0, ini relative cfg isn't passed to wma at all.
Change-Id: I1c3d137bb08624e30cc220e0fa0e31e6d6fc8a9d
CRs-Fixed: 2184096
Change Id872e2b0b8b7a203b472e0bd152f25f63c873b4f introduced support
for GAS public action frames in lim_process_action_frame and included
GAS frames under the frame_len check for minimum length of Vendor
specific public action frames. This would fail for GAS frames which
do not include OUI and could be as small as 3 octets.
Do frame_len check only for vendor specific public action frames
and remove the checks for GAS public action frames
Change-Id: I8b20925a23e2ba26d0a8df32eb3e5b2d043888d2
CRs-Fixed: 2187538
Check new channel width and center frequency segments in CSA
wider BW IE before processing the channel switch and if CSA IE
has invalid data for any of these parameters then do not do the
channel switch with wider BW.
Also check for self capability for BW that is supported by device
before processing wider BW channel switch. If AP advertises the new
channel width with valid data that is greater than self capability
BW value then limit the channel switch BW to self capability.
Change-Id: I1d567e5cdc6347b56b513ea002b5a3978cb447e9
CRs-Fixed: 2182054
Change CFG_VHT_ENABLE_1x1_TX/RX_CHAINMASK_DEFAULT to 0 which
indicates to don't care setting.
Change-Id: Ic16a2eba471bdfb77ecc0329c67b36b65a3b3489
CRs-Fixed: 2184433
CONFIG_GENL is not defined in some target
builds which is causing wlan load failure
with deubg message unknown symbol.
Fix the build load failures.
Change-Id: I448e405b099788c4c83303d9abdee9f7c1e45261
CRs-Fixed: 2188593
If 11ac override is enabled, change hw moed to 11ac and channel width
to the value defined in vht channel width ini. If channel list received
from hostapd contains only 2.4 Ghz channels, mismatch happens as hw mode
is 11ac but the channel list contains only 2.4 Ghz channels and no 5Ghz
channel.
Do 11ac override only when the channel list received from hostapd contains
5Ghz channel(s).
Change-Id: I28d9af3fed4b8487b50a4442221c1c880fe14c13
CRs-Fixed: 2186710
Add null check for pdev after cds_get_context, while
retrieving the context maintained by CDS
Change-Id: I2d6de7d5ad2a46139b2594cf966f2c083c9bb4b4
CRs-Fixed: 2187396
During init and deinit, the driver performs memdymp_init and
memdump_deinit. These are not done for the case when driver is in
FTM mode. In the present scenario, unloading the driver while in
FTM mode and then reloading causes problem.
Allow memdump_init and memdump_deinit to occur while the driver is
in FTM mode.
Change-Id: I4bed1bf76ee19612da9c27fe6cebb586ef7e542b
CRs-Fixed: 2170695
IPA Rx suspend command could be timed out because IPA Tx pipe stalls
due to FW WDI Tx pipe is already suspended beforehand.
Fix this by sending IPA Tx pipe suspend before FW WDI suspend.
Change-Id: I50c357ca0f8ddfcc1a51ad4ed040961daf052459
CRs-Fixed: 2177445
