Disable CTI save function on perf build to avoid the power and performance
issue.
Change-Id: Ic1a758418072248fa898e012ddb6f8d556efff22
Signed-off-by: Mao Jinlong <jinlmao@codeaurora.org>
These were helpful while working with extensions to NL80211_CMD_NEW_KEY,
so add more explicit error reporting for additional cases that can fail
while that command is being processed.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200222132548.20835-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Git-repo : git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
Git-commit: f8af764bf1cb86bed615baae84e3bbb6e4d3912d
CRs-Fixed: 2671591
Change-Id: Ib3ccbec2914b3f1c8e4ce0039d04b09020f362e4
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
If the HWO bit is set for the TRB (or the first TRB if scatter-gather
is used) of a request, it implies that core is still processing it.
In that case do not reclaim that TRB and also do not process
the request and give it back to the function driver.
Change-Id: Ia9fbaee443ad53d9a52909b0906a1d0ec1f2638a
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
This change enables spcom driver configuration as DLKM for GKI.
Change-Id: Ica83f7b5cec28ab227250e72c3ae09e6bef1a906
Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org>
On SSR, FW writes hang data in the carved out region from
existing DDR memory, the platform driver copies the hang
event data from the fixed offset to local buffer and sends
the buffer and length to host driver via CNSS_HANG_EVENT
event.
Change-Id: I5928821770086547b4fe17c30a967ea059b39394
Signed-off-by: Mohammed Siddiq <msiddiq@codeaurora.org>
When switch mode with etr being enabled more than one time, it needs
to reset all the etr settings for previous mode instead of return busy.
Change-Id: I243a6d910bb3dd8ac9ca30dadbd1c6ab3cefd00f
Signed-off-by: Mao Jinlong <jinlmao@codeaurora.org>
There is no need to proceed link down recovery if link has been recovered
by retries during power on sequence.
Change-Id: I876f2e239b519d4230b5c115cdc05ff7650f5cd1
Signed-off-by: Yue Ma <yuem@codeaurora.org>
With the valid SMMU IOVA range WLAN firmware is able to detect invalid
host DDR access before SMMU fault happens.
Change-Id: I3a3aac4e1da7bb7747bfe3b352df33fc87221860
Signed-off-by: Yue Ma <yuem@codeaurora.org>
EUD extcon device doesn't provide speed and cc_state information.
Hence skip querying speed and cc_state with it.
Change-Id: Ibe9e327fa412c8fd1fac0b1db3ba3be5d210f33c
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Agera PLL print registers are required to get the PLL values
from the debugfs, thus add support for the same.
Change-Id: I4b708958e1125ce7e8eab945a3c15113739230d4
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Agera PLL is required to be supported from HLOS clock controller, thus
add support for agera pll ops.
Change-Id: I77b2a741667accf9bd0eecfcd0dabfaf7596345f
Signed-off-by: Taniya Das <tdas@codeaurora.org>
The Legacy FSM Mode is required to be set when the Fabia PLL needs to be
used in non-FSM mode, thus add support for same.
Change-Id: I23d491cb33391dce1eb21d9ced298001da9ef907
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Burst size must be printed in perf builds as it is a major
characteristic of the system.
Change-Id: I7e6013751333bb487e2d9422726e41b1050aca43
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Update snapshot register list to add CP_APRIV_CNTL and CP_SMMU_STREAM_ID
registers. This is needed to capture complete CP state required for
debugging.
Change-Id: Icb8c35481de12dde43aab666f0ecad2240dcaa35
Signed-off-by: Deepak Kumar <dkumar@codeaurora.org>
MHI reset is triggered as part of EP shutdown. Shutdown
is blocked until MHI RESET bit is cleared in MHI CTRL reg.
There is a possibility of PCIe link going down during this
time. Since MHI RESET bit never gets cleared after 2 sec
wait_event_timeout reads the MHI CTRL reg and this results
into a memory abort. Fix this issue by using a boolean flag
as condition in wait_event_timeout. This flag is set when
MHI reset is triggered and cleared when reset is done.
Change-Id: I5b1831518255a38cde5b60406b5b9e9386b5477e
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
