Similarly to what done for the r8a7796 with commit 737e05bf03
("arm64: dts: renesas: revise properties for R-Car Gen3 SoCs'
usb 2.0"), this patch lists the clock for the USB High-Speed Module
(HS-USB) with the USB2.0 Host (EHCI/OHCI) IP DT node, and it lists
the clock for the USB2.0 Host IP with the HS-USB module DT node.
Fixes: 4c2c2fb998 ("arm64: dts: renesas: r8a774a1: Add USB2.0 phy and host(EHCI/OHCI) device nodes")
Fixes: ed898d4fc1 ("arm64: dts: renesas: r8a774a1: Add USB-DMAC and HSUSB device nodes")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds TMU[01234] device tree nodes to the r8a774a1
SoC specific DT.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the CMT[0123] device tree nodes to the
r8a774a1 SoC specific DT.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds uSD and eMMC support to the HiHope RZ/G2M
board.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the R8A77990 SoC uses DU{0,1}, the range from the base address to
the 0x4000 address is used.
This patch fixed it.
Fixes: 13ee2bfc54 ("arm64: dts: renesas: r8a77990: Add display output support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables TI HD3SS3220 device and support usb role switch
for the CAT 874 platform.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables USB3.0 host/peripheral device node for the cat874
board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the new renesas,companion property to the LVDS0 node to point to the
companion LVDS encoder LVDS1.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable RWDT and use 60 seconds as default timeout.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables PCIEC[01] PCI express controller on the sub board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare pcie bus clock, since it is generated on the HiHope RZ/G2M main
board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The HiHope RZ/G2M sub board sits below the HiHope RZ/G2M main board.
This patch also adds ethernet support along with a dtsi common to
both HiHope RZ/G2M and RZ/G2N sub boards.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds pincontrol support to scif2/scif clock.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the HiHope RZ/G2M main board:
- Memory,
- Main crystal,
- Serial console
This patch also includes a dtsi common to both HiHope RZ/G2M
and RZ/G2N main boards.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The RZ/G2M (a.k.a. r8a774a1) comes with two clusters of
processors, similarly to the r8a7796.
The first cluster is made of A57s, the second cluster is
made of A53s.
The operating points for the cluster with the A57s are:
Frequency | Voltage
-----------|---------
500 MHz | 0.82V
1.0 GHz | 0.82V
1.5 GHz | 0.82V
The operating points for the cluster with the A53s are:
Frequency | Voltage
-----------|---------
800 MHz | 0.82V
1.0 GHz | 0.82V
1.2 GHz | 0.82V
This patch adds the definitions for the operating points
to the SoC specific DT.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the dynamic power coefficient of A53 CPUs.
Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> and others.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Setup a thermal zone driven by SoC temperature sensor.
Create passive trip points and bind them to CPUFreq cooling
device that supports power extension.
In R-Car Gen3, IPA is supported for only one channel
Reason:
Currently, IPA controls base on only CPU temperature.
And only one thermal channel is assembled closest
CPU cores is selected as target of IPA.
If other channels are used, IPA controlling is not properly.
A single cooling device is described for all A53 CPUs as this
reflects that physically there is only one cooling device present.
This patch improves on an earlier version by:
* Omitting cooling-max-level and cooling-min-level properties which
are no longer present in mainline as of v4.17
* Removing an unused trip-point0 node sub-property from the trips
property.
* Defers adding dynamic-power-coefficient properties to a separate patch as
these are properties of the CPU.
The long signed-off by chain below reflects many revisions, mainly
internal, that this patch has been through.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the dynamic power coefficient of A57 and A53 CPUs.
Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> and others.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Setup a thermal zone driven by SoC temperature sensor.
Create passive trip points and bind them to CPUFreq cooling
device that supports power extension.
In R-Car Gen3, IPA is supported for only one channel
(on H3/M3/M3N SoCs, it is channel THS3). Reason:
Currently, IPA controls base on only CPU temperature.
And only one thermal channel is assembled closest
CPU cores is selected as target of IPA.
If other channels are used, IPA controlling is not properly.
The A57 cooling device supports 5 cooling states which can be categorised
as follows:
0 & 1) boost (clocking up)
2) default
3 & 4) cooling (clocking down)
Currently the thermal framework assumes that the default is the minimum,
or in other words there is no provision for handling boost states.
So this patch only describes the upper 3 states, default and cooling.
A single cooling device is described for all A57 CPUs and a separate
cooling device is described for all A53 CPUs. This reflects that physically
there is only one cooling device present for each type of CPU.
This patch improves on an earlier version by:
* Omitting cooling-max-level and cooling-min-level properties which
are no longer present in mainline as of v4.17
* Removing an unused trip-point0 node sub-property from the trips
property.
* Using cooling-device indexes such that maximum refers to maximum cooling
rather than the inverse.
* Defers adding dynamic-power-coefficient properties to a separate patch as
these are properties of the CPU.
The long signed-off by chain below reflects many revisions, mainly
internal, that this patch has been through.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: An Huynh <an.huynh.uj@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the dynamic power coefficient of A57 and A53 CPUs.
Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> and others.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Setup a thermal zone driven by SoC temperature sensor.
Create passive trip points and bind them to CPUFreq cooling
device that supports power extension.
In R-Car Gen3, IPA is supported for only one channel
(on H3/M3/M3N SoCs, it is channel THS3). Reason:
Currently, IPA controls base on only CPU temperature.
And only one thermal channel is assembled closest
CPU cores is selected as target of IPA.
If other channels are used, IPA controlling is not properly.
The A57 cooling device supports 5 cooling states which can be categorised
as follows:
0 & 1) boost (clocking up)
2) default
3 & 4) cooling (clocking down)
Currently the thermal framework assumes that the default is the minimum,
or in other words there is no provision for handling boost states.
So this patch only describes the upper 3 states, default and cooling.
A single cooling device is described for all A57 CPUs and a separate
cooling device is described for all A53 CPUs. This reflects that physically
there is only one cooling device present for each type of CPU.
This patch improves on an earlier version by:
* Omitting cooling-max-level and cooling-min-level properties which
are no longer present in mainline as of v4.17
* Removing an unused trip-point0 node sub-property from the trips
property.
* Using cooling-device indexes such that maximum refers to maximum cooling
rather than the inverse.
* Defers adding dynamic-power-coefficient properties to a separate patch as
these are properties of the CPU.
The long signed-off by chain below reflects many revisions, mainly
internal, that this patch has been through.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Hien Dang <hien.dang.eb@rvc.renesas.com>
Signed-off-by: An Huynh <an.huynh.uj@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the dynamic power coefficient of A57 and A53 CPUs.
Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> and others.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Setup a thermal zone driven by SoC temperature sensor.
Create passive trip points and bind them to CPUFreq cooling
device that supports power extension.
In R-Car Gen3, IPA is supported for only one channel
(on H3/M3/M3N SoCs, it is channel THS3). Reason:
Currently, IPA controls base on only CPU temperature.
And only one thermal channel is assembled closest
CPU cores is selected as target of IPA.
If other channels are used, IPA controlling is not properly.
The A5 cooling device supports 5 cooling states which can be categorised as
follows:
0 & 1) boost (clocking up)
2) default
3 & 4) cooling (clocking down)
Currently the thermal framework assumes that the default is the minimum,
or in other words there is no provision for handling boost states.
So this patch only describes the upper 3 states, default and cooling.
A single cooling device is described for all A57 CPUs and a separate
cooling device is described for all A53 CPUs. This reflects that physically
there is only one cooling device present for each type of CPU.
This patch improves on an earlier version by:
* Omitting cooling-max-level and cooling-min-level properties which
are no longer present in mainline as of v4.17
* Removing an unused trip-point0 node sub-property from the trips
property.
* Using cooling-device indexes such that maximum refers to maximum cooling
rather than the inverse.
* Defers adding dynamic-power-coefficient properties to a separate patch as
these are properties of the CPU.
The long signed-off by chain below reflects many revisions, mainly
internal, that this patch has been through.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Hien Dang <hien.dang.eb@rvc.renesas.com>
Signed-off-by: An Huynh <an.huynh.uj@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the commit 233da2c9ec ("dt-bindings: phy: rcar-gen3-phy-usb2:
Revise #phy-cells property") revised the #phy-cells, this patch follows
the updated document for R-Car Gen3 and RZ/A2 SoCs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It is incorrect to specify the no-ether-link property for the AVB device on
the Ebisu board. This is because the property should only be used when a
board does not provide a proper AVB_LINK signal. However, the Ebisu board
does provide this signal.
As per 87c059e9c3 ("arm64: dts: renesas: salvator-x: Remove renesas,
no-ether-link property") this fixes a bug:
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will have
impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since the
RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the present change is also a safety improvement because
it removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Fixes: 8441ef643d ("arm64: dts: renesas: r8a77990: ebisu: Enable EthernetAVB")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[simon: updated changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Apparently this DTS crossed over with commit 31af04cd60 ("arm64: dts:
Remove inconsistent use of 'arm,armv8' compatible string") and missed
out on the cleanup, so put it right.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert bootargs from ip=dhcp to ip=on
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables BT support for the CAT874 board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables WLAN support for the CAT874 board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add tpu device node to dtsi for TPU support on r8a7795 SoC.
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add tpu device node to dtsi for TPU support on r8a77965 SoC.
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add tpu device node to dtsi for TPU support on r8a7796 SoC.
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds description of TI WL1837 and links interfaces
to communicate with the IC, namely the SDIO interface to WLAN.
Signed-off-by: Spyridon Papageorgiou <spapageorgiou@de.adit-jv.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The ports node of vin4 only has one sub-node and thus does
not need #address-cells/#size-cells and the sub-node does
not need an exit.
This addresses the following warning:
# make dtbs W=1
...
arch/arm64/boot/dts/renesas/r8a77995-draak.dts:492.8-503.4: Warning (graph_child_address): /soc/video@e6ef4000/ports: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
Fixes: 6a0942c20f ("arm64: dts: renesas: draak: Describe CVBS input")
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The CAT874 board pushes sound via I2S over SSI0 into the
TDA19988BET chip.
This commit wires things up so that we can get sound out of
the HDMI interface.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The CAT874 board comes with a HDMI connector, managed by
a TDA19988BET chip, connected to the RZ/G2E SoC via DPAD.
This patch adds the necessary support to the board DT.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add IPMMU-DS0 to the Ethernet-AVB device node.
Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up r8a774a1 Audio-DMAC nodes to the IPMMU-MP.
Based on work for the r8a7795 by Magnus Damm.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up r8a774a1 DMAC nodes to the IPMMUs. In particular SYS-DMAC0
gets tied to IPMMU-DS0, and SYS-DMAC1 and SYS-DMAC2 get tied to IPMMU-DS1.
Based on work for the r8a7796 by Magnus Damm.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a774a1 has a single FDP1 instance similar to r8a7796.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DU device to r8a774a1.dtsi in a disabled state.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a774a1 soc has 5 VSP instances similar to r8a7796.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Build errors wrt. xattrs
- Mismerge which lead to a wrong Kconfig ifdef
- Missing endianness conversion
-----BEGIN PGP SIGNATURE-----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=0wS1
-----END PGP SIGNATURE-----
Merge tag 'upstream-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBIFS fixes from Richard Weinberger:
- build errors wrt xattrs
- mismerge which lead to a wrong Kconfig ifdef
- missing endianness conversion
* tag 'upstream-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubifs: Convert xattr inum to host order
ubifs: Use correct config name for encryption
ubifs: Fix build error without CONFIG_UBIFS_FS_XATTR
Merge yet more updates from Andrew Morton:
"A few final bits:
- large changes to vmalloc, yielding large performance benefits
- tweak the console-flush-on-panic code
- a few fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
panic: add an option to replay all the printk message in buffer
initramfs: don't free a non-existent initrd
fs/writeback.c: use rcu_barrier() to wait for inflight wb switches going into workqueue when umount
mm/compaction.c: correct zone boundary handling when isolating pages from a pageblock
mm/vmap: add DEBUG_AUGMENT_LOWEST_MATCH_CHECK macro
mm/vmap: add DEBUG_AUGMENT_PROPAGATE_CHECK macro
mm/vmalloc.c: keep track of free blocks for vmap allocation
- remove unneeded use of cc-option, cc-disable-warning, cc-ldoption
- exclude tracked files from .gitignore
- re-enable -Wint-in-bool-context warning
- refactor samples/Makefile
- stop building immediately if syncconfig fails
- do not sprinkle error messages when $(CC) does not exist
- move arch/alpha/defconfig to the configs subdirectory
- remove crappy header search path manipulation
- add comment lines to .config to clarify the end of menu blocks
- check uniqueness of module names (adding new warnings intentionally)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJc4KbfAAoJED2LAQed4NsGQW4P/3Iu+hM91EXqzdLqit99ML0x
9hI3Ap0Xd5HvPy+j0xYmAeXyBYolGOVcwGNLv2WMPxOkGFxcBTfVmBgYvugboX30
dwLMSXnL6MWL3xFVERTmRPl1STNwqHTnGal7Pru4HGUNnYUZJ9f9BGxoh0Qz55DJ
j5ZQ9RhnYS+DmEo6OmKJepoiM77Pf3W+prCegoZ+5ZtWnYd622p9d/rjiimR94RU
e5SFvGpSWbaUdaigjUqpA/GYW/iLy0T36xIUe20FQKe/8wstGOq61qKuPfgvxktA
y1ajRfQbZ/8D3lJyIU7AOZ9xgoY05lmbTEPb6eP8WygG7chKRakX/vy1+AHmDp9D
1K0IuwVdvFN2Qh5eLYkdtjX0tEUxX+m+CRv2NS75mNY/O3sTa7Yu6ZyZfCFRvGft
ZOU6Axskr/L0f048WLs0TGpDD8wyi9d2VZywKH+7Kr9KImeqGU0kRD/JzgvCFmcy
6lAfkptIMIL+VgSeN1igbJz6RjlGfTFvXPymvPzAcrTsVaxGHtjia/SC32h09Nw6
gS2vD2lv/sO0EaSUjwlwrHC0HVj3lEX3cIA0RGabbfbht1D7mnDjOyi7HWnbs80D
RHT4LCUuuPTufqCe+MQiQb08mcOSKcd58JdjZ1nfI/z/ME1zVkioMh63TFUPOfSX
T8zcEjd0wxdeLnyNj6fK
=oDeB
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- remove unneeded use of cc-option, cc-disable-warning, cc-ldoption
- exclude tracked files from .gitignore
- re-enable -Wint-in-bool-context warning
- refactor samples/Makefile
- stop building immediately if syncconfig fails
- do not sprinkle error messages when $(CC) does not exist
- move arch/alpha/defconfig to the configs subdirectory
- remove crappy header search path manipulation
- add comment lines to .config to clarify the end of menu blocks
- check uniqueness of module names (adding new warnings intentionally)
* tag 'kbuild-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (24 commits)
kconfig: use 'else ifneq' for Makefile to improve readability
kbuild: check uniqueness of module names
kconfig: Terminate menu blocks with a comment in the generated config
kbuild: add LICENSES to KBUILD_ALLDIRS
kbuild: remove 'addtree' and 'flags' magic for header search paths
treewide: prefix header search paths with $(srctree)/
media: prefix header search paths with $(srctree)/
media: remove unneeded header search paths
alpha: move arch/alpha/defconfig to arch/alpha/configs/defconfig
kbuild: terminate Kconfig when $(CC) or $(LD) is missing
kbuild: turn auto.conf.cmd into a mandatory include file
.gitignore: exclude .get_maintainer.ignore and .gitattributes
kbuild: add all Clang-specific flags unconditionally
kbuild: Don't try to add '-fcatch-undefined-behavior' flag
kbuild: add some extra warning flags unconditionally
kbuild: add -Wvla flag unconditionally
arch: remove dangling asm-generic wrappers
samples: guard sub-directories with CONFIG options
kbuild: re-enable int-in-bool-context warning
MAINTAINERS: kbuild: Add pattern for scripts/*vmlinux*
...
Pull i2c updates from Wolfram Sang:
"Some I2C core API additions which are kind of simple but enhance error
checking for users a lot, especially by returning errno now.
There are wrappers to still support the old API but it will be removed
once all users are converted"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: add device-managed version of i2c_new_dummy
i2c: core: improve return value handling of i2c_new_device and i2c_new_dummy
Unicode 12.1.0.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAlzg2qIACgkQ8vlZVpUN
gaPYfgf+IadtbeBYbKcHQzw8OZ9UxyGv7+Havs523XzhdceiflpOCe3lpSFYuX6w
0CtRIWEOqFzQLRHUlX/sRywYLvrvg3irDuYJGTzny9MfPEI+tVCkYi877PPAOOR3
4xay7dF63mcCpmhRxgw1fLx5I/hYpzrDnw5dGe7jjgU6SrR5FpE2GmEmbfBW087W
zAuRDkuTv03J791Kgpq4TAMNla9F2/oedq/2B0v43+TnKfYe1SEIDm3VusUvSfoI
++8CfRrRJ3D7vCmtFSuieFFb91HtHMqdv0gaad2cY1DfvJLVm7gP1uPL7QahA5Dq
VfhvFfqshqN9Jizr6BqP5GPOj2J9cw==
=QK+R
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Some bug fixes, and an update to the URL's for the final version of
Unicode 12.1.0"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: avoid panic during forced reboot due to aborted journal
ext4: fix block validity checks for journal inodes using indirect blocks
unicode: update to Unicode 12.1.0 final
unicode: add missing check for an error return from utf8lookup()
ext4: fix miscellaneous sparse warnings
ext4: unsigned int compared against zero
ext4: fix use-after-free in dx_release()
ext4: fix data corruption caused by overlapping unaligned and aligned IO
jbd2: fix potential double free
ext4: zero out the unused memory region in the extent tree block
-----BEGIN PGP SIGNATURE-----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=JhcA
-----END PGP SIGNATURE-----
Merge tag '5.2-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Minor cleanup and fixes, one for stable, four rdma (smbdirect)
related. Also adds SEEK_HOLE support"
* tag '5.2-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: add support for SEEK_DATA and SEEK_HOLE
Fixed https://bugzilla.kernel.org/show_bug.cgi?id=202935 allow write on the same file
cifs: Allocate memory for all iovs in smb2_ioctl
cifs: Don't match port on SMBDirect transport
cifs:smbd Use the correct DMA direction when sending data
cifs:smbd When reconnecting to server, call smbd_destroy() after all MIDs have been called
cifs: use the right include for signal_pending()
smb3: trivial cleanup to smb2ops.c
cifs: cleanup smb2ops.c and normalize strings
smb3: display session id in debug data
