Add initial support for plh scmi client driver which registers
into scmi framework for plh vendor protocol extension.
Also registers with plh interface driver msm_performance.
Change-Id: I448a714486ff4c7ea38cbeeec1ddb5e183b76e65
Signed-off-by: Gaurav Singh <sgaurav@codeaurora.org>
The perf lock hardening protocol is intended for the management
of perf lock hardening on RIMPS.
The commands in this protocol provide functionality to configure
plh details, plh tunables, configuring the log levels and
debugging support.
Change-Id: I9f5292ee3e32a038160e66d38ec15637a55458fd
Signed-off-by: Gaurav Singh <sgaurav@codeaurora.org>
Root_task_group is acessed outside CONFIG_SCHED_CGROUP
and it results in compilation error.so add macro check
here to avoid compile issue.
Change-Id: Ic3ce1962236f8114f8b03aca8ebd1c8fbd42a076
Signed-off-by: Biao Long <blong@codeaurora.org>
As per specs, while powering off/on the ufs device, RST_N signal and
REF_CLK signal should be between VSS(Ground) and VCCQ/VCCQ2.
Power down:
1. Assert RST_N low
2. Turn-off REF_CLK
3. Turn-off VCC
4. Turn-off VCCQ/VCCQ2.
power on:
1. Turn-on VCC
2. Turn-on VCCQ/VCCQ2
3. Turn-On REF_CLK
4. Deassert RST_N high.
Change-Id: I602e632d284a9d78431bf897558a4b8300ad3611
Signed-off-by: Ziqi Chen <ziqichen@codeaurora.org>
USB requests are being freed from 2 context from Linux QDSS driver:
1. usb_qdss_close()
2. explicitly calling usb_free_request() on receiving USB_QDSS_DISCONNECT
usb_qdss_close() is setting drvdata->usbch to NULL. Hence it ends up
passing usbch as NULL while calling usb_free_request() when handling
USB_QDSS_DISCONNECT. Fix this NULL pointer dereference issue by explicitly
checking USB channel against NULL with usb_qdss_free_req().
Change-Id: Ia55a30b09ab1f94db15947b984fd232a33da7788
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Add a new define for rmnet ioctl for setting MTU.
Change-Id: Ia3575605fc5066d0b98f1da252742e52ecbc3f11
Signed-off-by: Michael Adisumarta <madisuma@codeaurora.org>
In the case where the SW reset requires an additional ACD block reset or
misc reset, the support is added for the same.
Change-Id: I29b69f2a4ccc33a896ec8e201cbe761cca6800ea
Signed-off-by: Taniya Das <tdas@codeaurora.org>
When HDMI cable was pluged in/out, it could trigger an irq,
MSM can get HPD status from LT9611, and report the HPD status
using kernel uevent to userspace.
Change-Id: I47c148d92e877a80147ee81498513ead0e4afcf0
Signed-off-by: Wenjun Zhang <wjzhan@codeaurora.org>
During multiple adb reboots test case, adbd is taking time to start
and write the descriptors from the userspace. If adb is their in the
composition and its not ready when bind happens, UDC bind for ffs will
fail and adding the function back to the func_list in failure path and
calling purge_configs_funcs.
In purge_func adb driver unbind the functions from config->functions list
and add back to the tail of the func_list. With this order of the functions
in func_list got changed and next time when bind happens from adbd start
usb does not working.
Fix this issue by changing the order of the functions while adding the
functions back to the list in purge_configs_funcs.
Change-Id: I50c2362062130836d66edfcf8e1f020134248cb4
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Checking IPC log handle during usage rather than after creation.
This is because IPC logging is not available with boot image of
of GKI.
Change-Id: I81f4d5910bf721fd94f5858a2b7aba675a7be931
Signed-off-by: Karthik Poosa <kpoosa2@codeaurora.org>
SW trigger for PBS to configure ISC in LRA detection doesn't need to
pass any parameter or wait on any condition including checking status.
Hence switch using qpnp_pbs_trigger_single_event() instead of
qpnp_pbs_trigger_event() to trigger PBS.
Change-Id: I8b252e293265994976924435f8a6a11d9b463119
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
