Peer mac address is required in SAP mode TWT events.
So add support to send mac_address attribute in all
the TWT events to userspace.
Change-Id: Iab7c210eb2a058315b71f2327e6ac07d97ea7200
CRs-Fixed: 2940862
Correct the attribute policy for TWT suspend to fix the command
parsing failure.
Change-Id: I6078c2e199ed13433c3dea532e3bbe396dd6ad8a
CRs-Fixed: 2872500
Increase ce_service_max_yield_time to 2 msec in SLUB_DEBUG
builds for helium SNOC platforms to improve the CE reaping
performance.
Change-Id: I2a8a21fd1a65bc2ffc5fb17986116613f47510c7
CRs-Fixed: 2937231
wma_send_peer_assoc() calls wma_unified_peer_state_update() which
always sets the peer state as AUTH irrespective of peer state.
Remove wma_unified_peer_state_update() from wma_send_peer_assoc()
to handle peer state.
Change-Id: I4a887acbc8018653c34b927636cce7cc05323838
CRs-Fixed: 2888808
Do not intrabss forward fragmented EAPOL frames that have
DA different from the SAP vdev mac addr when high latency
is enabled.
Change-Id: Idb6e6c001f4dae51c2181e70ab9adbbb964f0ee3
CRs-Fixed: 2942096
Fragments are not flushed as part of rekey which
could result in fragments encrypted under different
keys to be reassembled.
Fix is to flush fragments for the peer for which add
key request is received.
Change-Id: I0c018ff7375272125c62aaea7b8ad4df9e842508
CRs-Fixed: 2875950
TWT notify event from firmware is expected only if the teardown
is initiated by the firmware during scenarios like
(roaming in progress, etc).
If the TWT teardown is initiated by the peer then notify WMI event
is not expected from the firmware.
Change-Id: Ic13a4858fb06d023d5e71da10320a546a1dcf80d
CRs-Fixed: 2944663
Fragmented EAPOL frames and EAPOL frames received
in few error scenarios with DA different from SAP
vdev mac addr will be dropped.
Change-Id: I624eba5bdb43c6b88a1f57112550f8026cc35e24
CRs-Fixed: 2888227
The INI skip_tpe_consideration when set, skips power from AP's
TPE IE in TPC power calculation for 2.4G/5G case. Enable this
INI by default since APs advertise low TPE powers for IoT, thus
lowering overall TPC power.
Change-Id: I6c07bbd684579c2fa3617e49d76c75b5bf3f2815
CRs-Fixed: 2941630
Modify check to ensure packet number is consecutive for
fragments and drop the fragments if the check fails.
Change-Id: Ica24f65aff65ca58bb010c876f27964b5b2bae6a
CRs-Fixed: 2860242
Drop non-EAPOL/WAPI frames from unauthorized peer received
in the IPA exception path.
Change-Id: I0c0bc6e60efa193126ba1e3eca36c5e02f7f76a3
CRs-Fixed: 2860206
Currently, TSO frames are not handled in packet capture mode.
Add support to handle TSO frames.
Change-Id: Ib901defcd369b01a33c87ca888ad80fe5fd086c7
CRs-Fixed: 2932138
Do not intrabss forward fragmented EAPOL frames that have
DA different from the SAP vdev mac addr.
Change-Id: I4145227c9b02fe8cec86ef4ffc3bc2025f906923
CRs-Fixed: 2888467
Multicast frames should not be fragmented and plaintext
frags should not be reassembeld in protected network.
Fix is to drop mcast frags and plaintext frags received
in protected network.
Change-Id: I98cf0715f5832f2f86f86b79dbdbc3a7c86dbfd0
CRs-Fixed: 2860245
For some of the stability issues triggered by H.W,
by the time host detects it most of the QDF history
is getting overwritten to avoid this increasing QDF
nbuf history. So that there will be less chance of
events getting overwritten.
Change-Id: Ia4bad1a175976af2e56126b56ae8c92a988e4289
CRs-Fixed: 2942868
Add pld_get_mhi_state API to get current MHI state and
pld_is_pci_ep_awake to indicate that PCI EP is out of
low power state.
Also enable pld_prevent_l1 and pld_allow_l1 API for WCN6750
to manage low power state of PCI EP from Host.
Change-Id: Ic574bf7d7886b8e59b98e65806b387eef3a54e94
Use wlan_reg_get_channel_state_for_freq to get channel state
instead of wlan_reg_get_channel_state.
Change-Id: I0ab0465458801747cc97bf03b3aee4ec255beb57
CRs-Fixed: 2859852
Some APs/P2P-GOs send beacon with 20mhz and assoc resp with 80mhz
and after assoc resp, next beacon also has 80mhz. Connection is
expected to happen in better possible bandwidth(80MHz in this
case).
Start the vdev with max supported ch_width in order to
support this. It'll be downgraded to appropriate ch_width or
the same would be continued based on assoc resp.
Change-Id: I0d205e0833b2638aab15401bacdef7a0696d40c2
CRs-Fixed: 2870758
Opportunistic timer gets triggered as soon as a DBS use case
is completed and hw_mode would be set to SMM when the
timer(5 seconds) expires.
Below is an example scenario,
1. DBS is enabled to support STA on 5GHz + SAP on 2.4GHz on
a Helium device.
2. SAP is disabled(to enable NAN as NAN+SAP is not supported on
HL platforms)
3. Opportunistic timer gets triggered with a timeout of 5 seconds
as DBS is not needed anymore.
4. Once the timer expires, WMI_PDEV_SET_HW_MODE_CMDID command
would be sent to firmware to set the hw_mode to SMM.
But if framework enables NAN immediately after disabling SAP,
firmware can't allow it as NAN is not supported in DBS mode in
Helium platforms. Thereby firmware either rejects the NAN enable
or defer it till set_hw_mode command is received(which introduces
a delay of 5 seconds as host sends it after timer expiry).
So, stop the timer and complete corresponding action when a NAN
command is received from framework to avoid this failure/delay.
Change-Id: I50521c0dd5f2314034957a0f65898c737cfe7e2e
CRs-Fixed: 2937407
At present LTE unsafe channel switch and DCS is using
hdd_switch_sap_channel to switch channel of SAP.
hdd_switch_sap_channel has no bw setting parameters and just
use the original bw of SAP - ch_width_orig. The ch_width_orig
(80Mhz) may not be applicable if SAP is channel switching from
5G 80Mhz to 2G. Use the new API wlan_get_ap_prefer_conc_ch_params
to override the bw to appropriate value for the new channel.
Change-Id: I9ab6c92a0534517c524bd56b0c3087d7f75f6368
CRs-Fixed: 2939654
Merge the bandwidth selection of the two API
wlansap_get_csa_chanwidth_from_phymode &
wlan_sap_get_concurrent.
Update 5G Force SCC target Max BW selection for dbs hw:
1. Max BW 80Mhz if sta_sap_scc_on_dfs_chan = 1 and Single SAP
2. Max BW 80Mhz if sta_sap_scc_on_dfs_chan = 0 and STA+SAP SCC
3. other case use User configured BW
The above Max BW value will be limited by SAP user configured
BW at the end.
Change-Id: I1b165d1411288ca6845f90103adbf8bbfc34f67d
CRs-Fixed: 2925750
Currently, there is no log to differentiate whether
igmp offload is not supported by fw or ini is disabled.
Add log to check the ini support of igmp offload and
fw capability to handle igmp request.
Change-Id: I22f6f9f1d11da5e03aa8d3c7869b81fc1acc51d7
CRs-Fixed: 2936131
HIF PM link state is used to indicate bus is alive or not. This
indicates RING HP/TP updating directly or using async method.In
RTPM suspend failure flow, CLD reject RTPM suspent request, but
state is not resumed correctly.
Change-Id: I3b96dc1fb34e2810d721e1fcb4db609a3d1d684d
CRs-Fixed: 2919930
Currently idle shutdown is flushed after the suspend dsc op
start. This can lead to the deadlock when the idle shutdown
work is running as it waits for the dsc ops to complete.
To mitigate this issue, flush the idle shutdown work before
starting the dsc ops in suspend sequence.
CRs-Fixed: 2941314
Change-Id: I023b9eb3543d83a30e0587cec3977e08ac7ab752
If ldpc bit is not set in case AP width more than
20 Mhz, it may cause crash.
So, force set LDPC coding in such cases.
Also, force set LDPC if peer supports MCS 10 and 11.
Change-Id: I14bb4b56d0efb660ad19587b319badfac9083f21
CRs-Fixed: 2915086
