Add the config entry to set the MaxPower to 900mA to accommodate
Super Speed and above.
Change-Id: I7e002b4942d1f5548c6d3281ac89e74f633b5723
Signed-off-by: Elson Roy Serrao <eserrao@codeaurora.org>
Currently 500mA is used as max allowable current to draw over
USB VBUS. However in SuperSpeed a gadget may draw up to 900mA
Update the CONFIG_USB_GADGET_VBUS_DRAW's allowable range to
be up to 900.
Change-Id: I781308065b30b260437f7b3180e276f6a657f504
Signed-off-by: Elson Roy Serrao <eserrao@codeaurora.org>
BHIe table size is printed incorrectly as unsigned long.
size is of type size_t hence use %zu instead of %lu.
Change-Id: Ic52bc6ea92e6dac8bd1e275f9a17986d08e2da79
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
This lock protects against any concurrent governor re-assignments
through sysfs. Furthermore, such re-assignment can lead to another
issue i.e. say someone assigns performance governor to this device
from sysfs. Then there can be a mismatch in what kgsl intends to
vote, and what actually gets voted. Therefore, fix both the min and
max frequencies for this devfreq device at the desired qos level so
that the intended vote is propagated regardless of the governor.
Change-Id: Ibc3b0ef1f585dae311aab028d8c2bc9f1a53b4b8
Signed-off-by: Harshdeep Dhatt <hdhatt@codeaurora.org>
Add sched_sync_hint_enable not to enable/disable sync.
Change-Id: Id6bdff3d4b9ea1051d7b55ca4cfd1d802c92fa64
Signed-off-by: Biao Long <blong@codeaurora.org>
WLAN host driver has a new memory requirement for regulatory structure
allocation of order 5. Increase 128 kB slot by one.
Change-Id: If95291c96df0b7588b54f8e19b287d846896b479
Signed-off-by: Mahesh Kumar Kalikot Veetil <mkalikot@codeaurora.org>
Use default RAM dump size if it is not defined in device tree node.
Also print MSI 64-bit address (high and low 32-bit) for debug purpose.
Change-Id: Iff382862e5a04ce995f2ec3bfeffaf7a1f6b78ee
Signed-off-by: Yue Ma <yuem@codeaurora.org>
Migrate isolate of a pageblock is being checked only at the pageblock
boundary pages thus the isolation of freepages should happen on that
pageblock which otherwise can still cause the isolation of freepages on
an isolated pageblock.
Consider the below case:
Pa Pb
check the pageblock
isolation
zone_lock
Isolate the SWAP_CLUSTER_MAX pages
Zone_unlock
zone_lock
Set Migrate isolate on the
same page block that Pa is
operating on.
zone_unlock
zone_lock
Continue the isolate on the same
page block that was set Migrate
isolate by Pb which is an error.
Change-Id: I1504b031f434fb65ebb11e1472b73e9d34e388b8
Fixes: ff56a97530 ("mem-offline: disallow page migration to isolated page blocks")
Signed-off-by: Charan Teja Reddy <charante@codeaurora.org>
Currently, qcom_icc_bcm_init always assumes the bcm is not initialized.
There is a possibility that same bcm can belong to multiple providers
and re-initing the bcm adds the same bcm multiple times to the nodes
which are under the control of the bcm.
Hence add condition to check for bcm inited.
Change-Id: I3961963a6ef1a7b76d7ab708f648146fe1a30c99
Signed-off-by: Veera Vegivada <vvegivad@codeaurora.org>
Define a vdd_levels enum and vdd_corner[] mapping table which can
be used by clock controller drivers to configure the vdd_class
associated with their clocks.
Change-Id: I7b1ad5f51c414694bc9d5101afc411b1d63bad42
Signed-off-by: Veera Vegivada <vvegivad@codeaurora.org>
