U1 and U2 are intermediate low power states. If host side and
device side u1 and u2 is supported then host sends a bus reset
signal when usb bus is idle which causes usb disconnect and connect.
This effects many automation runs as adb will be disconencted and
reconnected. Hence, disable u1, u2 on blair to solve this.
Change-Id: I3436b8e758976362919e199ddfad6b1ad659c152
Add a SW-calibrated ADC instance for PMR735A on holi-pm6125
which can be used if there is a requirement to read any ADC
channels on PMR735A.
Change-Id: I8bff473ca2605a3601283865138dabf0589b903e
Add bindings for SW-calibrated ADC used on PMR735A/PMR735B on
targets which don't have PMK8350 running in master mode.
Change-Id: I753b3caf1e52ac9920a9df32cbef465277409700
Enable cx ipeak lm device driver separately for blair and
holi-pm6125 targets based on latest devicetree configurations.
Change-Id: I3326ac8760d5eef3d6e6ff118c4c8a1e3e52c659
To prevent deadlocks between the clock and regulator frameworks,
the QUP clocks used by I2C-connected PMICs must be enabled all
the time and not registered with the clock framework. Skipping
the registration short-circuits the I2C device's clock calls such
that they return success before grabbing the clock locks. Achieve
this behavior by setting GCC's qcom,critical-devices property.
Change-Id: Idf812aa1df3a21670b8e9c262548cbf5f528e41b
Update mode threshold current of LDO6C of yupik to match
the threshold value expected by the client for HPM.
Change-Id: I60536af368d124eca816067471ed53bce7abf453
Observing probe defer and other related error to happen when
Charger or QG tries to probe before vadc. Fix this by adding
a dependency in DT for these drivers with "*-supply".
Change-Id: Ic4a7917a7aa84503dc9dcb8bc789768552077106
Update BCL thermal zone config with cdsp, gpu and modem
cooling devices for HOLI and its variants.
Change-Id: Iba8fa54af0948543527b4de0acc87cac0348be60
Correct #address-cells property for SPMI SID 1 of PM6125
to ensure module addresses under it can be read correctly.
Change-Id: I5380640c061715be34f6afc24925d117b51e0b32
Some platforms do not support L1 in HS mode and therefore need
to disable this feature through dt.
This change adds quirk snps,usb2_l1_disable in order to
avoid this.
Change-Id: Ifcafdfc51cc294d07e08192d96185cb772f06c5f
This reverts commit b979203071.
Dynamic clk gating requires to be disabled post Auto Hibernate
to avoid ice clk gating by dcg.
Change-Id: I7684ce7b6c314132616e4826d9d14cc438514e81
The EUD driver defaults to using INT1 for its interrupt mask.
However, on sdxlemur, this interrupt does not serve the apps
processor, so add the offset of the interrupt mask to the
device tree entry for EUD on sdxlemur.
Change-Id: I48e36cfead5f3b47ae97f4088cd019994654309e
The EUD driver defaults to using INT1 as the interrupt mask
for the apps processor. However, on modem, this interrupt
does not serve the apps processor, so add a new optional
device tree binding which can specify the offset of the
interrupt mask used for the apps processor and override the
default.
Change-Id: Id73336dcf737945effc254d3179bbfe354a5026b
Some platforms do not support l1 in HS mode and therefore need
to disable this feature through dt. This change adds quirk
snps,usb2_l1_disable in order to avoid this.
Change-Id: I5f06fed7e3f70d22d7f5099611f647b042d38d17
Add support for mpm interrupts on blair. These interrupts are
mapped to corresponding mpm pins and are needed for wakeup
events in case of xo shutdown.
Change-Id: I28806e252a243461a25b74a5b230d0ca4db3eb43
