If shmbridge is not enabled, allocate memory through
dma_alloc_coherent instead of shmbridge pool. This will make the
clients independent of whether shmbridge is enabled or
disabled.
Change-Id: I293872a2e57dec77d660de1bd857a425d4888a5b
Signed-off-by: Anmolpreet Kaur <anmolpre@codeaurora.org>
We add a vendor hook for util to freq calculation in schedutil,
so we need to do corresponding change for energy calculation.
android_vh_em_pd_energy
adjust energy calculation
Bug: 178021064
Signed-off-by: Yun Hsiang <yun.hsiang@mediatek.com>
Change-Id: Iae772cf07881602eea3f27aeb75fba753e7c2635
Add sched_sync_hint_enable not to enable/disable sync.
Change-Id: Id6bdff3d4b9ea1051d7b55ca4cfd1d802c92fa64
Signed-off-by: Biao Long <blong@codeaurora.org>
WLAN host driver has a new memory requirement for regulatory structure
allocation of order 5. Increase 128 kB slot by one.
Change-Id: If95291c96df0b7588b54f8e19b287d846896b479
Signed-off-by: Mahesh Kumar Kalikot Veetil <mkalikot@codeaurora.org>
Use default RAM dump size if it is not defined in device tree node.
Also print MSI 64-bit address (high and low 32-bit) for debug purpose.
Change-Id: Iff382862e5a04ce995f2ec3bfeffaf7a1f6b78ee
Signed-off-by: Yue Ma <yuem@codeaurora.org>
Migrate isolate of a pageblock is being checked only at the pageblock
boundary pages thus the isolation of freepages should happen on that
pageblock which otherwise can still cause the isolation of freepages on
an isolated pageblock.
Consider the below case:
Pa Pb
check the pageblock
isolation
zone_lock
Isolate the SWAP_CLUSTER_MAX pages
Zone_unlock
zone_lock
Set Migrate isolate on the
same page block that Pa is
operating on.
zone_unlock
zone_lock
Continue the isolate on the same
page block that was set Migrate
isolate by Pb which is an error.
Change-Id: I1504b031f434fb65ebb11e1472b73e9d34e388b8
Fixes: ff56a97530 ("mem-offline: disallow page migration to isolated page blocks")
Signed-off-by: Charan Teja Reddy <charante@codeaurora.org>
Currently, qcom_icc_bcm_init always assumes the bcm is not initialized.
There is a possibility that same bcm can belong to multiple providers
and re-initing the bcm adds the same bcm multiple times to the nodes
which are under the control of the bcm.
Hence add condition to check for bcm inited.
Change-Id: I3961963a6ef1a7b76d7ab708f648146fe1a30c99
Signed-off-by: Veera Vegivada <vvegivad@codeaurora.org>
Before initiating trusted touch, cancel any pending
suspend or resume work and wait for already scheduled worker
to finish.
Change-Id: I2a44e4e87eaf544d2190e4c9a125d40d7f9115d7
Signed-off-by: Shashank Babu Chinta Venkata <sbchin@codeaurora.org>
Before initiating trusted touch, cancel any pending
suspend or resume work and wait for already scheduled worker
to finish.
Change-Id: I9eb89a76e7238bf2ce18d319b9c50f2da784c703
Signed-off-by: Shashank Babu Chinta Venkata <sbchin@codeaurora.org>
The thermal zone config read callback is not holding lock before
accessing thermal instance list. There is a chance that both cooling
device binding and thermal zone config show read are happening
concurrently. The cooling device binding tries to add new thermal
instances and the same time thermal zone config show read context
tries to access thermal instance list. It leads to unexpected
behaviour.
Use lock before accessing thermal instance list in thermal zone
config read callback.
Change-Id: I1bea07cb67a7240027dd34cea2ff61def9258b8f
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org>
Currently, the frequency is calculated by max freq * 1.25 * util / max cap.
Add a vendor hook to adjust the frequency when the calculation
overestimate.
android_vh_map_util_freq
adjust util to freq calculation
Bug: 177845438
Signed-off-by: Yun Hsiang <yun.hsiang@mediatek.com>
Change-Id: I9aa9079f00af7d3380b19f2fe21b75cddd107d15
Define a vdd_levels enum and vdd_corner[] mapping table which can
be used by clock controller drivers to configure the vdd_class
associated with their clocks.
Change-Id: I7b1ad5f51c414694bc9d5101afc411b1d63bad42
Signed-off-by: Veera Vegivada <vvegivad@codeaurora.org>
To avoid any suspend during probe, we increment the device
usage counter before calling ufshcd_async_scan and decrement
before returning from ufshcd_async_scan function.
For the scenarios where ufs device initialisation fails
or if the ufs device is not present, we are decrementing
device usage counter before calling ufshcd_hba_exit.
Hence there is a possiblity that after we disable the clocks
as part of ufshcd_hba_exit call, runtime suspend may get
triggered. As part of runtime suspend, we are accessing
the register causing noc error due to unclocked access.
To fix this, we are removing pm_runtime_put_sync
from ufshcd_add_lus() and adding it in common place
at the end of ufshcd_async_scan so that we hold auto
suspend until async scan completes in both success and
failure case.
Call Stack:
panic+0x17c
panic+0x0
arm64_serror_panic+0x74
do_serror+0x15c
el1_error+0xbc
el1_irq+0xb0
crypto_qti_resume+0x68
ufshcd_crypto_qti_resume+0x18
ufshcd_crypto_resume+0x3c
ufshcd_suspend+0x5b0
ufshcd_runtime_suspend+0x44
ufshcd_pltfrm_runtime_suspend+0x14
pm_generic_runtime_suspend+0x44
__rpm_callback+0x98
rpm_suspend+0x2a4
rpm_idle+0x158
schedule+0x8c
schedule_preempt_disabled+0x24
__mutex_lock+0x358
__mutex_lock_slowpath+0x14
mutex_lock+0x34
clk_unprepare+0x58
__ufshcd_setup_clocks+0x140
ufshcd_hba_exit+0x170
ufshcd_async_scan$d36fba0b664edbd124b5d17d005db4c5+0x118
async_run_entry_fn$8847b5d726ee295ba72a029a76bec2f5+0x60
process_one_work+0x2cc
worker_thread$f31e2447a3fdcb60f4b193f95acd647c+0x278
kthread$bf1537fa370ac32bde5f056194ddafc6+0x16c
ret_from_fork+0x10.
Change-Id: I059de2b0eba642bf1a35c27e8e12d31c6f30a836
Signed-off-by: Nitin Rawat <nitirawa@codeaurora.org>
This change Enhances IPC logs to add SE instance to know which
GPII is attached to which SE device, this helps in debug. Also,
removed unnecessary read of iommu-dma property.
Change-Id: I6a5a9312d80abab2addc0c63642429a787f9065c
Signed-off-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Update GPIOs(151 and 202) for wake capability disablement on
lahaina and shima.
Change-Id: I97f114ceaf454c3653e69ff912c6b78fd718e8fe
Signed-off-by: Mohammed Siddiq <msiddiq@codeaurora.org>
Enable CONFIG_ARM_SMMU_SELFTEST for debug config. The actual
interrupt self test runs only when arm_smmu.selftest is set to 1.
Change-Id: I040ba9d5d98ff2e9dbbc579e8a0f5062d9bedfd4
Signed-off-by: Charan Teja Reddy <charante@codeaurora.org>
Replace existing non standard power supply properties with standard power
supply properties to make the smb358 driver GKI complaint.
Change-Id: I878f0e910a8819e55befef5914be13190e1ce6c0
Signed-off-by: Kavya Nunna <knunna@codeaurora.org>
Current code is reducing total_pages by pcount for each
loop iteration which results in decrementing total_pages
incorrectly as pcount is total number of pages reduced
in all previous iterations. Incorrect total_pages results
in incorrect nr_removed. Fix this by not decrementing
total_pages and directly accounting for already reduced
pages in nr_removed calculation.
Change-Id: I69485c26f1f98974eecc30caa1a888ddeafe7c73
Signed-off-by: Deepak Kumar <dkumar@codeaurora.org>
configfs_composite_unbind sets the gadget data
to null. Therefore, add check in disconnect
function to make sure that cdev is not NULL.
Prints a WARN message if the driver tries to
redundantly disconnect a gadget.
Change-Id: Iad25f7a1e785ed336d34259c147efdcfc0840fae
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Git-commit: da17b0d6e3031d54deb05c08c7bf1616da43f7a6
Git-Repo: https://android.googlesource.com/kernel/common/
Signed-off-by: Pratham Pratap <prathampratap@codeaurora.org>
Add support for sm8150-llcc driver. The driver
is written by taking reference from sm8150-llcc
driver in msm-4.14 kernel at commit id
"f6969550b4".
Change-Id: Iaa7711f56066fc1c8e098beaf19185522bb5581d
Signed-off-by: Vivek Kumar <vivekuma@codeaurora.org>
This change enables PDC device for sdmsteppeauto.
Change-Id: Iae030f810aca280c22b36f3539244ff6c8c961bc
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Enable ARM SMMU as module and add other IOMMU related
features and debug support for gen3auto.
Change-Id: Ifb40974d87bed1826ea9694daa6f3c44c338dc40
Signed-off-by: Vivek Kumar <vivekuma@codeaurora.org>
Handle the CTS counter whenever the change in CTS interrupt occur.
Using the M_IO_DATA_ASSERT bit in interrupt register, this will get
set when CTS is high.
Change-Id: I43c629f4d026af4a7e82d0d6d01b826259b0b1b5
Signed-off-by: Venkata Manasa Kakarla <venkka@codeaurora.org>
* remotes/origin/tmp-5327444:
ANDROID: GKI: Add Sony KMI symbol list
Change-Id: I313d7220d2a301b13db1c3a7ed5d7df82a1f741e
Signed-off-by: Srinivasarao P <spathi@codeaurora.org>
Enables the debug pagge alloc config and debug page alloc enable
default config for holi.
Change-Id: I8bea46c944c126425ed6a1fe129403dcba75f364
Signed-off-by: Faiyaz Mohammed <faiyazm@codeaurora.org>
Signed-off-by: Prakash Gupta <guptap@codeaurora.org>
add bpf configs which are used for device
bootup.
Change-Id: Ibdad44bf74a49e26cba852cfdf28791a61f7819d
Signed-off-by: Chandrasekhar Mattaparthy <cmatta@codeaurora.org>
