Add snapshot of smb358 charger documentation from msm-4.14
'commit 50f9f83dd79b ("Merge "defconfig : Enable pinctrl and
clock driver for SA8195"")'.
SMB358 is a single-cell battery charger. It can charge
the battery and power the system via the USB/AC adapter input.
Change-Id: Id3aef2dab81a67061d728f661ce568917e86b08e
Add snapshot of smb1351 charger documentation from msm-4.14
'commit 50f9f83dd79b ("Merge "defconfig : Enable pinctrl and
clock driver for SA8195"")'.
SMB1351 is a single-cell battery charger. It can charge
the battery and power the system via the USB/AC adapter input.
Change-Id: Ife4403bfe2ee577f0e4c952432861bcccb3be076
QCA6490 requires synchronization between BT and WLAN GPIOs for PMU
power up. Update CNSS device tree node for BT GPIO config.
Change-Id: I0cd7050dad499378ec6d2bcfbe9d78f4a79a3384
This change adds a documentation of SPI BLSP driver from the 4.19
branch. kernel-4.19 baseline: 'commit b159d5da02b7
("dt-bindings: Add documentation for SDM660")'.
Change-Id: I64177a6323a14aad4269f7825a8258b7ab1c4389
This change adds a snapshot of I2C MSM V2 driver from the 4.14
branch. kernel-4.14 baseline: 'commit 2aa77f468a3d
("i2c-msm-v2: Replace HW recovery mechanism with SW bit-banging")'.
Change-Id: Ia0604ce27bdf29018b911d7ab2baa3e70d70b31f
This change adds a snapshot of SPS DMA driver from the 4.19
branch. kernel-4.19 baseline: 'commit b159d5da02b7
("dt-bindings: Add documentation for SDM660")'.
Change-Id: I1997961ee887e0657602e3456cee7f1ff88ae368
Add dt-bindings for UART BLSP driver.
This change adds a snapshot of BLSP UART driver bindings from the
4.14 branch. kernel-4.14 baseline: 'commit 5b51cb0c0e2c474f1f
("serial: msm_serial_hs: Add snapshot of serial highspeed driver")'.
Removed ICB bus voting properties and replaced them with
new ICC framework properties.
Change-Id: I8316c36375ed34d008e6d6e456e807ecc5814b39
PCIe internal AUX clock frequency used to be either 1MHz or
19.2MHz. The devicetree entry was a boolean type to determine
which frequency to program in PCIe controller. Newer chipsets
may support other frequencies such as 16.6MHz. Update the
devicetree entry so that it accepts a decimal value for the
desired frequency to be programmed in PCIe controller.
Change-Id: I5818f5973ddbbce4268eafb6e99202daeba4234a
Add interconnect device bindings. These devices can be used
to describe any RPMH and NoC based interconnect devices.
Change-Id: Icf836295d471a2ee661f772dea883d0bf07ede9c
Add cnss-enable-self-recovery flag for lahaina. It enables
self recovery on link down. Update the documentation
for the cnss-enable-self-recovery flag.
Change-Id: Ifd9f3c23ec8e6c56874f6964cd8134520c2e9c6d
Add display-panels property for the ECM device to get the display
blank and unblank notifications from the active panel device and
re-enable ECM dynamically.
Change-Id: Ia82f60a7f21908b69a7ba19a1884e955f0bad227
VBUS can be detected via a dedicated PMIC pin. Enable compatible string
that adds support for reporting the VBUS status.
Change-Id: I65d5879a3288e2f5e37d8f674e7216a1aebfe52a
Add binding documentation for SMB1390 charger. SMB1390 is a charge pump
PMIC and is used as a companion charger to the primary charging PMIC.
This is a snapshot from msm-4.19 commit 94e8e08c6890
(" ARM: dts: msm: Correct the dev_id for hdmi cpu-dai").
Change-Id: Idfc0eadb74e0bfa67842de4f610e208de011b05e
