commit d77b6ff0ce35a6d0b0b7b9581bc3f76d041d4087 upstream.
batadv_nc_skb_decode_packet() trusts coded_len and checks only against
skb->len. XOR starts at sizeof(struct batadv_unicast_packet), reducing
payload headroom, and the source skb length is not verified, allowing an
out-of-bounds read and a small out-of-bounds write.
Validate that coded_len fits within the payload area of both destination
and source sk_buffs before XORing.
Fixes: 2df5278b02 ("batman-adv: network coding - receive coded packets and decode them")
Cc: stable@vger.kernel.org
Reported-by: Stanislav Fort <disclosure@aisle.com>
Signed-off-by: Stanislav Fort <stanislav.fort@aisle.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 548b0c5de7619ef53bbde5590700693f2f6d2a56 upstream.
An OGMv1 and OGMv2 packet receive processing were not only limited by the
number of bytes in the received packet but also by the nodes maximum
aggregation packet size limit. But this limit is relevant for TX and not
for RX. It must not be enforced by batadv_(i)v_ogm_aggr_packet to avoid
loss of information in case of a different limit for sender and receiver.
This has a minor side effect for B.A.T.M.A.N. IV because the
batadv_iv_ogm_aggr_packet is also used for the preprocessing for the TX.
But since the aggregation code itself will not allow more than
BATADV_MAX_AGGREGATION_BYTES bytes, this check was never triggering (in
this context) prior of removing it.
Cc: stable@vger.kernel.org
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Fixes: 9323158ef9 ("batman-adv: OGMv2 - implement originators logic")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c8ecc98f5c65947b0070a24bac11e12e47cc65d upstream.
The ELP worker needs to calculate new metric values for all neighbors
"reachable" over an interface. Some of the used metric sources require
locks which might need to sleep. This sleep is incompatible with the RCU
list iterator used for the recorded neighbors. The initial approach to work
around of this problem was to queue another work item per neighbor and then
run this in a new context.
Even when this solved the RCU vs might_sleep() conflict, it has a major
problems: Nothing was stopping the work item in case it is not needed
anymore - for example because one of the related interfaces was removed or
the batman-adv module was unloaded - resulting in potential invalid memory
accesses.
Directly canceling the metric worker also has various problems:
* cancel_work_sync for a to-be-deactivated interface is called with
rtnl_lock held. But the code in the ELP metric worker also tries to use
rtnl_lock() - which will never return in this case. This also means that
cancel_work_sync would never return because it is waiting for the worker
to finish.
* iterating over the neighbor list for the to-be-deactivated interface is
currently done using the RCU specific methods. Which means that it is
possible to miss items when iterating over it without the associated
spinlock - a behaviour which is acceptable for a periodic metric check
but not for a cleanup routine (which must "stop" all still running
workers)
The better approch is to get rid of the per interface neighbor metric
worker and handle everything in the interface worker. The original problems
are solved by:
* creating a list of neighbors which require new metric information inside
the RCU protected context, gathering the metric according to the new list
outside the RCU protected context
* only use rcu_trylock inside metric gathering code to avoid a deadlock
when the cancel_delayed_work_sync is called in the interface removal code
(which is called with the rtnl_lock held)
Cc: stable@vger.kernel.org
Fixes: c833484e5f ("batman-adv: ELP - compute the metric based on the estimated throughput")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7e34ffc976aaae4f465b7898303241b81ceefc3 upstream.
If a temporary error happened in the evaluation of the neighbor throughput
information, then the invalid throughput result should not be stored in the
throughtput EWMA.
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccb7276a6d26d6f8416e315b43b45e15ee7f29e2 upstream.
Reference counting is used to ensure that
batadv_hardif_neigh_node and batadv_hard_iface
are not freed before/during
batadv_v_elp_throughput_metric_update work is
finished.
But there isn't a guarantee that the hard if will
remain associated with a soft interface up until
the work is finished.
This fixes a crash triggered by reboot that looks
like this:
Call trace:
batadv_v_mesh_free+0xd0/0x4dc [batman_adv]
batadv_v_elp_throughput_metric_update+0x1c/0xa4
process_one_work+0x178/0x398
worker_thread+0x2e8/0x4d0
kthread+0xd8/0xdc
ret_from_fork+0x10/0x20
(the batadv_v_mesh_free call is misleading,
and does not actually happen)
I was able to make the issue happen more reliably
by changing hardif_neigh->bat_v.metric_work work
to be delayed work. This allowed me to track down
and confirm the fix.
Cc: stable@vger.kernel.org
Fixes: c833484e5f ("batman-adv: ELP - compute the metric based on the estimated throughput")
Signed-off-by: Andy Strohman <andrew@andrewstrohman.com>
[sven@narfation.org: prevent entering batadv_v_elp_get_throughput without
soft_iface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fff8f17c1a6fc802ca23bbd3a276abfde8cc58e6 ]
When TT changes list is too big to fit in packet due to MTU size, an
empty OGM is sent expected other node to send TT request to get the
changes. The issue is that tt.last_changeset was not built thus the
originator was responding with previous changes to those TT requests
(see batadv_send_my_tt_response). Also the changes list was never
cleaned up effectively never ending growing from this point onwards,
repeatedly sending the same TT response changes over and over, and
creating a new empty OGM every OGM interval expecting for the local
changes to be purged.
When there is more TT changes that can fit in packet, drop all changes,
send empty OGM and wait for TT request so we can respond with a full
table instead.
Fixes: e1bf0c1409 ("batman-adv: tvlv - convert tt data sent within OGMs")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Acked-by: Antonio Quartulli <Antonio@mandelbit.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8038806db64da15721775d6b834990cacbfcf0b2 ]
The number of entries filled by batadv_tt_tvlv_generate() can be less
than initially expected in batadv_tt_prepare_tvlv_{global,local}_data()
(changes can be removed by batadv_tt_local_event() in ADD+DEL sequence
in the meantime as the lock held during the whole tvlv global/local data
generation).
Thus tvlv_len could be bigger than the actual TT entry size that need
to be sent so full table TT_RESPONSE could hold invalid TT entries such
as below.
* 00:00:00:00:00:00 -1 [....] ( 0) 88:12:4e:ad:7e:ba (179) (0x45845380)
* 00:00:00:00:78:79 4092 [.W..] ( 0) 88:12:4e:ad:7e:3c (145) (0x8ebadb8b)
Remove the extra allocated space to avoid sending uninitialized entries
for full table TT_RESPONSE in both batadv_send_other_tt_response() and
batadv_send_my_tt_response().
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2f7358c3890e7366cbcb7512b4bc8b4394b2d61 ]
The number of TT changes can be less than initially expected in
batadv_tt_tvlv_container_update() (changes can be removed by
batadv_tt_local_event() in ADD+DEL sequence between reading
tt_diff_entries_num and actually iterating the change list under lock).
Thus tt_diff_len could be bigger than the actual changes size that need
to be sent. Because batadv_send_my_tt_response sends the whole
packet, uninitialized data can be interpreted as TT changes on other
nodes leading to weird TT global entries on those nodes such as:
* 00:00:00:00:00:00 -1 [....] ( 0) 88:12:4e:ad:7e:ba (179) (0x45845380)
* 00:00:00:00:78:79 4092 [.W..] ( 0) 88:12:4e:ad:7e:3c (145) (0x8ebadb8b)
All of the above also applies to OGM tvlv container buffer's tvlv_len.
Remove the extra allocated space to avoid sending uninitialized TT
changes in batadv_send_my_tt_response() and batadv_v_ogm_send_softif().
Fixes: e1bf0c1409 ("batman-adv: tvlv - convert tt data sent within OGMs")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 537a350d14321c8cca5efbf0a33a404fec3a9f9e upstream.
The internal handling of VLAN IDs in batman-adv is only specified for
following encodings:
* VLAN is used
- bit 15 is 1
- bit 11 - bit 0 is the VLAN ID (0-4095)
- remaining bits are 0
* No VLAN is used
- bit 15 is 0
- remaining bits are 0
batman-adv was only preparing new translation table entries (based on its
soft interface information) using this encoding format. But the receive
path was never checking if entries in the roam or TT TVLVs were also
following this encoding.
It was therefore possible to create more than the expected maximum of 4096
+ 1 entries in the originator VLAN list. Simply by setting the "remaining
bits" to "random" values in corresponding TVLV.
Cc: stable@vger.kernel.org
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1f532a3b1e6d2e5559c7ace49322922637a28aa upstream.
If the MTU of one of an attached interface becomes too small to transmit
the local translation table then it must be resized to fit inside all
fragments (when enabled) or a single packet.
But if the MTU becomes too low to transmit even the header + the VLAN
specific part then the resizing of the local TT will never succeed. This
can for example happen when the usable space is 110 bytes and 11 VLANs are
on top of batman-adv. In this case, at least 116 byte would be needed.
There will just be an endless spam of
batman_adv: batadv0: Forced to purge local tt entries to fit new maximum fragment MTU (110)
in the log but the function will never finish. Problem here is that the
timeout will be halved all the time and will then stagnate at 0 and
therefore never be able to reduce the table even more.
There are other scenarios possible with a similar result. The number of
BATADV_TT_CLIENT_NOPURGE entries in the local TT can for example be too
high to fit inside a packet. Such a scenario can therefore happen also with
only a single VLAN + 7 non-purgable addresses - requiring at least 120
bytes.
While this should be handled proactively when:
* interface with too low MTU is added
* VLAN is added
* non-purgeable local mac is added
* MTU of an attached interface is reduced
* fragmentation setting gets disabled (which most likely requires dropping
attached interfaces)
not all of these scenarios can be prevented because batman-adv is only
consuming events without the the possibility to prevent these actions
(non-purgable MAC address added, MTU of an attached interface is reduced).
It is therefore necessary to also make sure that the code is able to handle
also the situations when there were already incompatible system
configuration are present.
Cc: stable@vger.kernel.org
Fixes: a19d3d85e1 ("batman-adv: limit local translation table max size")
Reported-by: syzbot+a6a4b5bb3da165594cff@syzkaller.appspotmail.com
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 987aae75fc1041072941ffb622b45ce2359a99b9 upstream.
The automatic recalculation of the maximum allowed MTU is usually triggered
by code sections which are already rtnl lock protected by callers outside
of batman-adv. But when the fragmentation setting is changed via
batman-adv's own batadv genl family, then the rtnl lock is not yet taken.
But dev_set_mtu requires that the caller holds the rtnl lock because it
uses netdevice notifiers. And this code will then fail the check for this
lock:
RTNL: assertion failed at net/core/dev.c (1953)
Cc: stable@vger.kernel.org
Reported-by: syzbot+f8812454d9b3ac00d282@syzkaller.appspotmail.com
Fixes: c6a953cce8d0 ("batman-adv: Trigger events for auto adjusted MTU")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230821-batadv-missing-mtu-rtnl-lock-v1-1-1c5a7bfe861e@narfation.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d25ddb7e788d34cf27ff1738d11a87cb4b67d446 upstream.
When a client roamed back to a node before it got time to destroy the
pending local entry (i.e. within the same originator interval) the old
global one is directly removed from hash table and left as such.
But because this entry had an extra reference taken at lookup (i.e using
batadv_tt_global_hash_find) there is no way its memory will be reclaimed
at any time causing the following memory leak:
unreferenced object 0xffff0000073c8000 (size 18560):
comm "softirq", pid 0, jiffies 4294907738 (age 228.644s)
hex dump (first 32 bytes):
06 31 ac 12 c7 7a 05 00 01 00 00 00 00 00 00 00 .1...z..........
2c ad be 08 00 80 ff ff 6c b6 be 08 00 80 ff ff ,.......l.......
backtrace:
[<00000000ee6e0ffa>] kmem_cache_alloc+0x1b4/0x300
[<000000000ff2fdbc>] batadv_tt_global_add+0x700/0xe20
[<00000000443897c7>] _batadv_tt_update_changes+0x21c/0x790
[<000000005dd90463>] batadv_tt_update_changes+0x3c/0x110
[<00000000a2d7fc57>] batadv_tt_tvlv_unicast_handler_v1+0xafc/0xe10
[<0000000011793f2a>] batadv_tvlv_containers_process+0x168/0x2b0
[<00000000b7cbe2ef>] batadv_recv_unicast_tvlv+0xec/0x1f4
[<0000000042aef1d8>] batadv_batman_skb_recv+0x25c/0x3a0
[<00000000bbd8b0a2>] __netif_receive_skb_core.isra.0+0x7a8/0xe90
[<000000004033d428>] __netif_receive_skb_one_core+0x64/0x74
[<000000000f39a009>] __netif_receive_skb+0x48/0xe0
[<00000000f2cd8888>] process_backlog+0x174/0x344
[<00000000507d6564>] __napi_poll+0x58/0x1f4
[<00000000b64ef9eb>] net_rx_action+0x504/0x590
[<00000000056fa5e4>] _stext+0x1b8/0x418
[<00000000878879d6>] run_ksoftirqd+0x74/0xa4
unreferenced object 0xffff00000bae1a80 (size 56):
comm "softirq", pid 0, jiffies 4294910888 (age 216.092s)
hex dump (first 32 bytes):
00 78 b1 0b 00 00 ff ff 0d 50 00 00 00 00 00 00 .x.......P......
00 00 00 00 00 00 00 00 50 c8 3c 07 00 00 ff ff ........P.<.....
backtrace:
[<00000000ee6e0ffa>] kmem_cache_alloc+0x1b4/0x300
[<00000000d9aaa49e>] batadv_tt_global_add+0x53c/0xe20
[<00000000443897c7>] _batadv_tt_update_changes+0x21c/0x790
[<000000005dd90463>] batadv_tt_update_changes+0x3c/0x110
[<00000000a2d7fc57>] batadv_tt_tvlv_unicast_handler_v1+0xafc/0xe10
[<0000000011793f2a>] batadv_tvlv_containers_process+0x168/0x2b0
[<00000000b7cbe2ef>] batadv_recv_unicast_tvlv+0xec/0x1f4
[<0000000042aef1d8>] batadv_batman_skb_recv+0x25c/0x3a0
[<00000000bbd8b0a2>] __netif_receive_skb_core.isra.0+0x7a8/0xe90
[<000000004033d428>] __netif_receive_skb_one_core+0x64/0x74
[<000000000f39a009>] __netif_receive_skb+0x48/0xe0
[<00000000f2cd8888>] process_backlog+0x174/0x344
[<00000000507d6564>] __napi_poll+0x58/0x1f4
[<00000000b64ef9eb>] net_rx_action+0x504/0x590
[<00000000056fa5e4>] _stext+0x1b8/0x418
[<00000000878879d6>] run_ksoftirqd+0x74/0xa4
Releasing the extra reference from batadv_tt_global_hash_find even at
roam back when batadv_tt_global_free is called fixes this memory leak.
Cc: stable@vger.kernel.org
Fixes: 068ee6e204 ("batman-adv: roaming handling mechanism redesign")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by; Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8e42a2b0addf238be8b3b37dcd9795a5c1be459 upstream.
If the user set an MTU value, it usually means that there are special
requirements for the MTU. But if an interface gots activated, the MTU was
always recalculated and then the user set value was overwritten.
The only reason why this user set value has to be overwritten, is when the
MTU has to be decreased because batman-adv is not able to transfer packets
with the user specified size.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6a953cce8d0438391e6da48c8d0793d3fbfcfa6 upstream.
If an interface changes the MTU, it is expected that an NETDEV_PRECHANGEMTU
and NETDEV_CHANGEMTU notification events is triggered. This worked fine for
.ndo_change_mtu based changes because core networking code took care of it.
But for auto-adjustments after hard-interfaces changes, these events were
simply missing.
Due to this problem, non-batman-adv components weren't aware of MTU changes
and thus couldn't perform their own tasks correctly.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abac3ac97fe8734b620e7322a116450d7f90aa43 upstream.
Syzkaller got a lot of crashes like:
KASAN: use-after-free Write in *_timers*
All of these crashes point to the same memory area:
The buggy address belongs to the object at ffff88801f870000
which belongs to the cache kmalloc-8k of size 8192
The buggy address is located 5320 bytes inside of
8192-byte region [ffff88801f870000, ffff88801f872000)
This area belongs to :
batadv_priv->batadv_priv_dat->delayed_work->timer_list
The reason for these issues is the lack of synchronization. Delayed
work (batadv_dat_purge) schedules new timer/work while the device
is being deleted. As the result new timer/delayed work is set after
cancel_delayed_work_sync() was called. So after the device is freed
the timer list contains pointer to already freed memory.
Found by Linux Verification Center (linuxtesting.org) with syzkaller.
Cc: stable@kernel.org
Fixes: 2f1dfbe185 ("batman-adv: Distributed ARP Table - implement local storage")
Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a063f2fba3fa633a599253b62561051ac185fa99 ]
The receiving interface might have used GRO to receive more fragments than
MAX_SKB_FRAGS fragments. In this case, these will not be stored in
skb_shinfo(skb)->frags but merged into the frag list.
batman-adv relies on the function skb_split to split packets up into
multiple smaller packets which are not larger than the MTU on the outgoing
interface. But this function cannot handle frag_list entries and is only
operating on skb_shinfo(skb)->frags. If it is still trying to split such an
skb and xmit'ing it on an interface without support for NETIF_F_FRAGLIST,
then validate_xmit_skb() will try to linearize it. But this fails due to
inconsistent information. And __pskb_pull_tail will trigger a BUG_ON after
skb_copy_bits() returns an error.
In case of entries in frag_list, just linearize the skb before operating on
it with skb_split().
Reported-by: Felix Kaechele <felix@kaechele.ca>
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Tested-by: Felix Kaechele <felix@kaechele.ca>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 145c7a793838add5e004e7d49a67654dc7eba147 ]
This fixes minor data-races in ip6_mc_input() and
batadv_mcast_mla_rtr_flags_softif_get_ipv6()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6c1f41afc1dbe59d9d3c8bb0d80b749c119aa334 upstream.
The ifindex doesn't have to be unique for multiple network namespaces on
the same machine.
$ ip netns add test1
$ ip -net test1 link add dummy1 type dummy
$ ip netns add test2
$ ip -net test2 link add dummy2 type dummy
$ ip -net test1 link show dev dummy1
6: dummy1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 96:81:55:1e:dd:85 brd ff:ff:ff:ff:ff:ff
$ ip -net test2 link show dev dummy2
6: dummy2: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 5a:3c:af:35:07:c3 brd ff:ff:ff:ff:ff:ff
But the batman-adv code to walk through the various layers of virtual
interfaces uses this assumption because dev_get_iflink handles it
internally and doesn't return the actual netns of the iflink. And
dev_get_iflink only documents the situation where ifindex == iflink for
physical devices.
But only checking for dev->netdev_ops->ndo_get_iflink is also not an option
because ipoib_get_iflink implements it even when it sometimes returns an
iflink != ifindex and sometimes iflink == ifindex. The caller must
therefore make sure itself to check both netns and iflink + ifindex for
equality. Only when they are equal, a "physical" interface was detected
which should stop the traversal. On the other hand, vxcan_get_iflink can
also return 0 in case there was currently no valid peer. In this case, it
is still necessary to stop.
Fixes: b7eddd0b39 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Fixes: 5ed4a460a1 ("batman-adv: additional checks for virtual interfaces on top of WiFi")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6116ba09423f7d140f0460be6a1644dceaad00da upstream.
There is no need to call dev_get_iflink multiple times for the same
net_device in batadv_get_real_netdevice. And since some of the
ndo_get_iflink callbacks are dynamic (for example via RCUs like in
vxcan_get_iflink), it could easily happen that the returned values are not
stable. The pre-checks before __dev_get_by_index are then of course bogus.
Fixes: 5ed4a460a1 ("batman-adv: additional checks for virtual interfaces on top of WiFi")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 690bb6fb64f5dc7437317153902573ecad67593d upstream.
There is no need to call dev_get_iflink multiple times for the same
net_device in batadv_is_on_batman_iface. And since some of the
.ndo_get_iflink callbacks are dynamic (for example via RCUs like in
vxcan_get_iflink), it could easily happen that the returned values are not
stable. The pre-checks before __dev_get_by_index are then of course bogus.
Fixes: b7eddd0b39 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9057d6c23e7388ee9d037fccc9a7bc8557ce277b ]
Currently, creating a batman-adv interface in an unprivileged LXD
container and attaching secondary interfaces to it with "ip" or "batctl"
works fine. However all batctl debug and configuration commands
fail:
root@container:~# batctl originators
Error received: Operation not permitted
root@container:~# batctl orig_interval
1000
root@container:~# batctl orig_interval 2000
root@container:~# batctl orig_interval
1000
To fix this change the generic netlink permissions from GENL_ADMIN_PERM
to GENL_UNS_ADMIN_PERM. This way a batman-adv interface is fully
maintainable as root from within a user namespace, from an unprivileged
container.
All except one batman-adv netlink setting are per interface and do not
leak information or change settings from the host system and are
therefore save to retrieve or modify as root from within an unprivileged
container.
"batctl routing_algo" / BATADV_CMD_GET_ROUTING_ALGOS is the only
exception: It provides the batman-adv kernel module wide default routing
algorithm. However it is read-only from netlink and an unprivileged
container is still not allowed to modify
/sys/module/batman_adv/parameters/routing_algo. Instead it is advised to
use the newly introduced "batctl if create routing_algo RA_NAME" /
IFLA_BATADV_ALGO_NAME to set the routing algorithm on interface
creation, which already works fine in an unprivileged container.
Cc: Tycho Andersen <tycho@tycho.pizza>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 938f2e0b57ffe8a6df71e1e177b2978b1b33fe5e upstream.
The addition of routable multicast TX handling introduced a
bug/regression for packets with a link-local multicast destination:
These packets would be sent to all batman-adv nodes with a multicast
router and to all batman-adv nodes with an old version without multicast
router detection.
This even disregards the batman-adv multicast fanout setting, which can
potentially lead to an unwanted, high number of unicast transmissions or
even congestion.
Fixing this by avoiding to send link-local multicast packets to nodes in
the multicast router list.
Fixes: 11d458c1cb ("batman-adv: mcast: apply optimizations for routable packets, too")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 992b03b88e36254e26e9a4977ab948683e21bd9f upstream.
When a packet is fragmented by batman-adv, the original batman-adv header
is not modified. Only a new fragmentation is inserted between the original
one and the ethernet header. The code must therefore make sure that it has
a writable region of this size in the skbuff head.
But it is not useful to always reallocate the skbuff by this size even when
there would be more than enough headroom still in the skb. The reallocation
is just to costly during in this codepath.
Fixes: ee75ed8887 ("batman-adv: Fragment and send skbs larger than mtu")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5cbfc87558168ef4c3c27ce36eba6b83391db19 upstream.
The batadv net_device is trying to propagate the needed_headroom and
needed_tailroom from the lower devices. This is needed to avoid cost
intensive reallocations using pskb_expand_head during the transmission.
But the fragmentation code split the skb's without adding extra room at the
end/beginning of the various fragments. This reduced the performance of
transmissions over complex scenarios (batadv on vxlan on wireguard) because
the lower devices had to perform the reallocations at least once.
Fixes: ee75ed8887 ("batman-adv: Fragment and send skbs larger than mtu")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ca23e2c2074465bff55ea14221175fecdf63c5f upstream.
If a batman-adv packets has to be fragmented, then the original batman-adv
packet header is not stripped away. Instead, only a new header is added in
front of the packet after it was split.
This size must be considered to avoid cost intensive reallocations during
the transmission through the various device layers.
Fixes: 7bca68c784 ("batman-adv: Add lower layer needed_(head|tail)room to own ones")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f68cd634856f8ca93bafd623ba5357e0f648c68 upstream.
Syzbot reported ODEBUG warning in batadv_nc_mesh_free(). The problem was
in wrong error handling in batadv_mesh_init().
Before this patch batadv_mesh_init() was calling batadv_mesh_free() in case
of any batadv_*_init() calls failure. This approach may work well, when
there is some kind of indicator, which can tell which parts of batadv are
initialized; but there isn't any.
All written above lead to cleaning up uninitialized fields. Even if we hide
ODEBUG warning by initializing bat_priv->nc.work, syzbot was able to hit
GPF in batadv_nc_purge_paths(), because hash pointer in still NULL. [1]
To fix these bugs we can unwind batadv_*_init() calls one by one.
It is good approach for 2 reasons: 1) It fixes bugs on error handling
path 2) It improves the performance, since we won't call unneeded
batadv_*_free() functions.
So, this patch makes all batadv_*_init() clean up all allocated memory
before returning with an error to no call correspoing batadv_*_free()
and open-codes batadv_mesh_free() with proper order to avoid touching
uninitialized fields.
Link: https://lore.kernel.org/netdev/000000000000c87fbd05cef6bcb0@google.com/ [1]
Reported-and-tested-by: syzbot+28b0702ada0bf7381f58@syzkaller.appspotmail.com
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9f460ae31c4435fd022c443a6029352217a16ac1 ]
The soft/batadv interface for a queued OGM can be changed during the time
the OGM was queued for transmission and when the OGM is actually
transmitted by the worker.
But WARN_ON must be used to denote kernel bugs and not to print simple
warnings. A warning can simply be printed using pr_warn.
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Reported-by: syzbot+c0b807de416427ff3dd1@syzkaller.appspotmail.com
Fixes: ef0a937f7a ("batman-adv: consider outgoing interface in OGM sending")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 08c27f3322fec11950b8f1384aa0f3b11d028528 upstream.
KMSAN found uninitialized value at batadv_tt_prepare_tvlv_local_data()
[1], for commit ced72933a5 ("batman-adv: use CRC32C instead of CRC16
in TT code") inserted 'reserved' field into "struct batadv_tvlv_tt_data"
and commit 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN
specific") moved that field to "struct batadv_tvlv_tt_vlan_data" but left
that field uninitialized.
[1] https://syzkaller.appspot.com/bug?id=07f3e6dba96f0eb3cabab986adcd8a58b9bdbe9d
Reported-by: syzbot <syzbot+50ee810676e6a089487b@syzkaller.appspotmail.com>
Tested-by: syzbot <syzbot+50ee810676e6a089487b@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: ced72933a5 ("batman-adv: use CRC32C instead of CRC16 in TT code")
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 14a2e551faea53d45bc11629a9dac88f88950ca7 ]
If THIS_MODULE is not set, the module would be removed while debugfs is
being used.
It eventually makes kernel panic.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2369e827046920ef0599e6a36b975ac5c0a359c2 ]
Scenario:
* Multicast frame send from BLA backbone gateways (multiple nodes
with their bat0 bridged together, with BLA enabled) sharing the same
LAN to nodes in the mesh
Issue:
* Nodes receive the frame multiple times on bat0 from the mesh,
once from each foreign BLA backbone gateway which shares the same LAN
with another
For multicast frames via batman-adv broadcast packets coming from the
same BLA backbone but from different backbone gateways duplicates are
currently detected via a CRC history of previously received packets.
However this CRC so far was not performed for multicast frames received
via batman-adv unicast packets. Fixing this by appyling the same check
for such packets, too.
Room for improvements in the future: Ideally we would introduce the
possibility to not only claim a client, but a complete originator, too.
This would allow us to only send a multicast-in-unicast packet from a BLA
backbone gateway claiming the node and by that avoid potential redundant
transmissions in the first place.
Fixes: 279e89b2281a ("batman-adv: add broadcast duplicate check")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74c09b7275126da1b642b90c9cdc3ae8b729ad4b ]
Scenario:
* Multicast frame send from mesh to a BLA backbone (multiple nodes
with their bat0 bridged together, with BLA enabled)
Issue:
* BLA backbone nodes receive the frame multiple times on bat0,
once from mesh->bat0 and once from each backbone_gw from LAN
For unicast, a node will send only to the best backbone gateway
according to the TQ. However for multicast we currently cannot determine
if multiple destination nodes share the same backbone if they don't share
the same backbone with us. So we need to keep sending the unicasts to
all backbone gateways and let the backbone gateways decide which one
will forward the frame. We can use the CLAIM mechanism to make this
decision.
One catch: The batman-adv gateway feature for DHCP packets potentially
sends multicast packets in the same batman-adv unicast header as the
multicast optimizations code. And we are not allowed to drop those even
if we did not claim the source address of the sender, as for such
packets there is only this one multicast-in-unicast packet.
How can we distinguish the two cases?
The gateway feature uses a batman-adv unicast 4 address header. While
the multicast-to-unicasts feature uses a simple, 3 address batman-adv
unicast header. So let's use this to distinguish.
Fixes: fe2da6ff27 ("batman-adv: check incoming packet type for bla")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3236d215ad38a3f5372e65cd1e0a52cf93d3c6a2 ]
Scenario:
* Multicast frame send from a BLA backbone (multiple nodes with
their bat0 bridged together, with BLA enabled)
Issue:
* BLA backbone nodes receive the frame multiple times on bat0
For multicast frames received via batman-adv broadcast packets the
originator of the broadcast packet is checked before decapsulating and
forwarding the frame to bat0 (batadv_bla_is_backbone_gw()->
batadv_recv_bcast_packet()). If it came from a node which shares the
same BLA backbone with us then it is not forwarded to bat0 to avoid a
loop.
When sending a multicast frame in a non-4-address batman-adv unicast
packet we are currently missing this check - and cannot do so because
the batman-adv unicast packet has no originator address field.
However, we can simply fix this on the sender side by only sending the
multicast frame via unicasts to interested nodes which do not share the
same BLA backbone with us. This also nicely avoids some unnecessary
transmissions on mesh side.
Note that no infinite loop was observed, probably because of dropping
via batadv_interface_tx()->batadv_bla_tx(). However the duplicates still
utterly confuse switches/bridges, ICMPv6 duplicate address detection and
neighbor discovery and therefore leads to long delays before being able
to establish TCP connections, for instance. And it also leads to the Linux
bridge printing messages like:
"br-lan: received packet on eth1 with own address as source address ..."
Fixes: 2d3f6ccc4e ("batman-adv: Modified forwarding behaviour for multicast packets")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bba9dab86b6ac15ca560ef1f2b5aa4529cbf784 ]
The fix for receiving (internally generated) bla packets outside the
interrupt context introduced the usage of in_interrupt(). But this
functionality is only defined in linux/preempt.h which was not included
with the same patch.
Fixes: 279e89b2281a ("batman-adv: bla: use netif_rx_ni when not in interrupt context")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dda5b3384121181c4e79f6eaeac2b94c0622c8d ]
The unicast packet rerouting code makes several assumptions. For
instance it assumes that there is always exactly one destination in the
TT. This breaks for multicast frames in a unicast packets in several ways:
For one thing if there is actually no TT entry and the destination node
was selected due to the multicast tvlv flags it announced. Then an
intermediate node will wrongly drop the packet.
For another thing if there is a TT entry but the TTVN of this entry is
newer than the originally addressed destination node: Then the
intermediate node will wrongly redirect the packet, leading to
duplicated multicast packets at a multicast listener and missing
packets at other multicast listeners or multicast routers.
Fixing this by not applying the unicast packet rerouting to batman-adv
unicast packets with a multicast payload. We are not able to detect a
roaming multicast listener at the moment and will just continue to send
the multicast frame to both the new and old destination for a while in
case of such a roaming multicast listener.
Fixes: a73105b8d4 ("batman-adv: improved client announcement mechanism")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 097930e85f90f252c44dc0d084598265dd44ca48 ]
It seems that due to a copy & paste error the void pointer
in batadv_choose_backbone_gw() is cast to the wrong type.
Fixing this by using "struct batadv_bla_backbone_gw" instead of "struct
batadv_bla_claim" which better matches the caller's side.
For now it seems that we were lucky because the two structs both have
their orig/vid and addr/vid in the beginning. However I stumbled over
this issue when I was trying to add some debug variables in front of
"orig" in batadv_backbone_gw, which caused hash lookups to fail.
Fixes: 07568d0369 ("batman-adv: don't rely on positions in struct for hashing")
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 279e89b2281af3b1a9f04906e157992c19c9f163 ]
batadv_bla_send_claim() gets called from worker thread context through
batadv_bla_periodic_work(), thus netif_rx_ni needs to be used in that
case. This fixes "NOHZ: local_softirq_pending 08" log messages seen
when batman-adv is enabled.
Fixes: 23721387c4 ("batman-adv: add basic bridge loop avoidance code")
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8bf0c01642275c7dca1e5d02c34e4199c200b1f ]
The own OGM check is currently misplaced and can lead to the following
issues:
For one thing we might receive an aggregated OGM from a neighbor node
which has our own OGM in the first place. We would then not only skip
our own OGM but erroneously also any other, following OGM in the
aggregate.
For another, we might receive an OGM aggregate which has our own OGM in
a place other then the first one. Then we would wrongly not skip this
OGM, leading to populating the orginator and gateway table with ourself.
Fixes: 9323158ef9 ("batman-adv: OGMv2 - implement originators logic")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 303216e76dcab6049c9d42390b1032f0649a8206 ]
The gateway client code can try to optimize the delivery of DHCP packets to
avoid broadcasting them through the whole mesh. But also transmissions to
the client can be optimized by looking up the destination via the chaddr of
the DHCP packet.
But the chaddr is currently only done when chaddr is fully inside the
non-paged area of the skbuff. Otherwise it will not be initialized and the
unoptimized path should have been taken.
But the implementation didn't handle this correctly. It didn't retrieve the
correct chaddr but still tried to perform the TT lookup with this
uninitialized memory.
Reported-by: syzbot+ab16e463b903f5a37036@syzkaller.appspotmail.com
Fixes: 6c413b1c22 ("batman-adv: send every DHCP packet as bat-unicast")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ad346c90509ebd983f60da7d082f261ad329507 ]
The commit 8c46fcd783 ("batman-adv: disable ethtool link speed detection
when auto negotiation off") disabled the usage of ethtool's link_ksetting
when auto negotation was enabled due to invalid values when used with
tun/tap virtual net_devices. According to the patch, automatic measurements
should be used for these kind of interfaces.
But there are major flaws with this argumentation:
* automatic measurements are not implemented
* auto negotiation has nothing to do with the validity of the retrieved
values
The first point has to be fixed by a longer patch series. The "validity"
part of the second point must be addressed in the same patch series by
dropping the usage of ethtool's link_ksetting (thus always doing automatic
measurements over ethernet).
Drop the patch again to have more default values for various net_device
types/configurations. The user can still overwrite them using the
batadv_hardif's BATADV_ATTR_THROUGHPUT_OVERRIDE.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6f91a3f7af4186099dd10fa530dd7e0d9c29747d upstream.
batadv_v_ogm_process() invokes batadv_hardif_neigh_get(), which returns
a reference of the neighbor object to "hardif_neigh" with increased
refcount.
When batadv_v_ogm_process() returns, "hardif_neigh" becomes invalid, so
the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling paths of
batadv_v_ogm_process(). When batadv_v_ogm_orig_get() fails to get the
orig node and returns NULL, the refcnt increased by
batadv_hardif_neigh_get() is not decreased, causing a refcnt leak.
Fix this issue by jumping to "out" label when batadv_v_ogm_orig_get()
fails to get the orig node.
Fixes: 9323158ef9 ("batman-adv: OGMv2 - implement originators logic")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6107c5da0fca8b50b4d3215e94d619d38cc4a18c upstream.
batadv_show_throughput_override() invokes batadv_hardif_get_by_netdev(),
which gets a batadv_hard_iface object from net_dev with increased refcnt
and its reference is assigned to a local pointer 'hard_iface'.
When batadv_store_throughput_override() returns, "hard_iface" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The issue happens in one error path of
batadv_store_throughput_override(). When batadv_parse_throughput()
returns NULL, the refcnt increased by batadv_hardif_get_by_netdev() is
not decreased, causing a refcnt leak.
Fix this issue by jumping to "out" label when batadv_parse_throughput()
returns NULL.
Fixes: 0b5ecc6811 ("batman-adv: add throughput override attribute to hard_ifaces")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f872de8185acf1b48b954ba5bd8f9bc0a0d14016 upstream.
batadv_show_throughput_override() invokes batadv_hardif_get_by_netdev(),
which gets a batadv_hard_iface object from net_dev with increased refcnt
and its reference is assigned to a local pointer 'hard_iface'.
When batadv_show_throughput_override() returns, "hard_iface" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The issue happens in the normal path of
batadv_show_throughput_override(), which forgets to decrease the refcnt
increased by batadv_hardif_get_by_netdev() before the function returns,
causing a refcnt leak.
Fix this issue by calling batadv_hardif_put() before the
batadv_show_throughput_override() returns in the normal path.
Fixes: 0b5ecc6811 ("batman-adv: add throughput override attribute to hard_ifaces")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd0c42c4dea54335967c5a86f15fc064235a2797 upstream.
and change to pseudorandom numbers, as this is a traffic dithering
operation that doesn't need crypto-grade.
The previous code operated in 4 steps:
1. Generate a random byte 0 <= rand_tq <= 255
2. Multiply it by BATADV_TQ_MAX_VALUE - tq
3. Divide by 255 (= BATADV_TQ_MAX_VALUE)
4. Return BATADV_TQ_MAX_VALUE - rand_tq
This would apperar to scale (BATADV_TQ_MAX_VALUE - tq) by a random
value between 0/255 and 255/255.
But! The intermediate value between steps 3 and 4 is stored in a u8
variable. So it's truncated, and most of the time, is less than 255, after
which the division produces 0. Specifically, if tq is odd, the product is
always even, and can never be 255. If tq is even, there's exactly one
random byte value that will produce a product byte of 255.
Thus, the return value is 255 (511/512 of the time) or 254 (1/512
of the time).
If we assume that the truncation is a bug, and the code is meant to scale
the input, a simpler way of looking at it is that it's returning a random
value between tq and BATADV_TQ_MAX_VALUE, inclusive.
Well, we have an optimized function for doing just that.
Fixes: 3c12de9a5c ("batman-adv: network coding - code and transmit packets if possible")
Signed-off-by: George Spelvin <lkml@sdf.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e8ce08198de193e3d21d42e96945216e3d9ac7f upstream.
A transmission scheduling for an interface which is currently dropped by
batadv_iv_ogm_iface_disable could still be in progress. The B.A.T.M.A.N. V
is simply cancelling the workqueue item in an synchronous way but this is
not possible with B.A.T.M.A.N. IV because the OGM submissions are
intertwined.
Instead it has to stop submitting the OGM when it detect that the buffer
pointer is set to NULL.
Reported-by: syzbot+a98f2016f40b9cd3818a@syzkaller.appspotmail.com
Reported-by: syzbot+ac36b6a33c28a491e929@syzkaller.appspotmail.com
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Hillf Danton <hdanton@sina.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cc4a1708903f404d2ca0dfde30e71e052c6cbc9 upstream.
The distributed arp table is using a DHT to store and retrieve MAC address
information for an IP address. This is done using unicast messages to
selected peers. The potential peers are looked up using the IP address and
the VID.
While the IP address is always stored in big endian byte order, this is not
the case of the VID. It can (depending on the host system) either be big
endian or little endian. The host must therefore always convert it to big
endian to ensure that all devices calculate the same peers for the same
lookup data.
Fixes: be1db4f661 ("batman-adv: make the Distributed ARP Table vlan aware")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Fix free/alloc race for OGM and OGMv2, by Sven Eckelmann (2 patches)
-----BEGIN PGP SIGNATURE-----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=usWf
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20191025' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are two batman-adv bugfixes:
* Fix free/alloc race for OGM and OGMv2, by Sven Eckelmann (2 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some interface types could be nested.
(VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, VIRT_WIFI, VXLAN, etc..)
These interface types should set lockdep class because, without lockdep
class key, lockdep always warn about unexisting circular locking.
In the current code, these interfaces have their own lockdep class keys and
these manage itself. So that there are so many duplicate code around the
/driver/net and /net/.
This patch adds new generic lockdep keys and some helper functions for it.
This patch does below changes.
a) Add lockdep class keys in struct net_device
- qdisc_running, xmit, addr_list, qdisc_busylock
- these keys are used as dynamic lockdep key.
b) When net_device is being allocated, lockdep keys are registered.
- alloc_netdev_mqs()
c) When net_device is being free'd llockdep keys are unregistered.
- free_netdev()
d) Add generic lockdep key helper function
- netdev_register_lockdep_key()
- netdev_unregister_lockdep_key()
- netdev_update_lockdep_key()
e) Remove unnecessary generic lockdep macro and functions
f) Remove unnecessary lockdep code of each interfaces.
After this patch, each interface modules don't need to maintain
their lockdep keys.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
