1. Remove irq timer handler which is used by outdated IC.
2. Skip irq close request send from HAL. For now, HAL open and close
irq in very high freq, and at last, irq will be set to open state.
When HW report IRQ, but HAL set irq state to close. This will cause
missing IRQ issue.
Change-Id: I5448ef89cfe988197d4204b17e4764b730ec1ad4
Signed-off-by: haojl2 <haojl2@motorola.com>
Reviewed-on: https://gerrit.mot.com/1407246
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Yan Zhang <zhangy26@motorola.com>
Reviewed-by: Weilong Wu <wuwl10@motorola.com>
Reviewed-by: Jianqi Yang <yangj@motorola.com>
Submit-Approved: Jira Key
Both panel suppliers: BOE and CSOT are changing Tx/Rx layout while
switching from EVT to DVT revision of HW. LSI provides no facility
in their firmware to distinguish HW variants. Thus driver will be
matching panel id and version in chosen node with id and version
for EVT provided as a mapping table in LSI device tree.
Change-Id: I265caced054f19ab2f985bf798dd169e09097fa0
Signed-off-by: Konstantin Makariev <hcv867@motorola.com>
Reviewed-on: https://gerrit.mot.com/1406669
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
Submit-Approved: Jira Key
Added multiple suspend/resume scenarios to the driver. First option is
to perform HW reset on resume. It implies that touch IC will be put
to sleep mode when suspended. Device tree property sec,reset-on-resume
controls it. Second option is to turn power supplies off when suspended.
Device tree property sec,power-off-suspend controls it. Second option
takes precedence over first one when both enabled in device tree.
Change-Id: I93a99152397ea15f46a01c2f1a0ca8bd68c9f732
Signed-off-by: Konstantin Makariev <hcv867@motorola.com>
Reviewed-on: https://gerrit.mot.com/1405038
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
Submit-Approved: Jira Key
Clean up some unused macros. Fix charger mode set function
Change-Id: If80fc134db1a2132e30e4b12a1e565fffd0bc197
Signed-off-by: Konstantin Makariev <hcv867@motorola.com>
Reviewed-on: https://gerrit.mot.com/1405014
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
Submit-Approved: Jira Key
Added USB cable detection support to better handle charging noise.
This is optional feature controlled via device tree property
sec,usb-charger-detection. Fixed suspend mode current drain by
using sleep power mode instead LPM.
Change-Id: I53357cd578ec8412006dcf664558776c6cbadb7b
Signed-off-by: Konstantin Makariev <hcv867@motorola.com>
Reviewed-on: https://gerrit.mot.com/1403963
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
Submit-Approved: Jira Key
-solve that sar sensor of olso-h didn't work
-Compatible with previous projects
Change-Id: I33a2cdd2065205491f78e4f7d111e3bb124fc0af
Signed-off-by: chenlj2 <chenlj2@motorola.com>
Reviewed-on: https://gerrit.mot.com/1404580
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Jiacheng Ou <oujc1@motorola.com>
Reviewed-by: Wen Xie <xiewen3@motorola.com>
Reviewed-by: Tao Sun <suntao2@motorola.com>
Submit-Approved: Jira Key
Update ram info to handle ddr5, which uses a new
struct from the bootloader with an extra flag.
Also re-work error handling, previously it was possible
that if a wrong size is returned, the pointer to the
smem struct might not be null and we will still try
to access it, causing a panic. So, do not add the
sysfs entry if it is not correct.
Change-Id: Ib195543175528d0477266281080c4dc4a96abd3c
Signed-off-by: Ryan Lattrel <ryanl@motorola.com>
Reviewed-on: https://gerrit.mot.com/1402645
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Reviewed-by: Dong-Hua Yan <a18317@motorola.com>
Reviewed-by: Curtis Porter <porterc@motorola.com>
Tested-by: Jira Key
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
Submit-Approved: Jira Key
Fix missing includes and warnings that show up when
building with the clang compiler.
Change-Id: I3eadc724df1598c4c2efe0ca1e18d6a6b7013367
Signed-off-by: Ryan Lattrel <ryanl@motorola.com>
Reviewed-on: https://gerrit.mot.com/1401055
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Reviewed-by: Curtis Porter <porterc@motorola.com>
Tested-by: Jira Key
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
Submit-Approved: Jira Key
Set voltage might fail due to regulator constraints settings, which is
not fatal error and thus should not fail the probe.
Change-Id: I4e1c5dae7acb2fddd5eedbdbc1bab3a81ef4f961
Signed-off-by: Konstantin Makariev <hcv867@motorola.com>
Reviewed-on: https://gerrit.mot.com/1400192
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Submit-Approved: Jira Key
Since the device is detected by i2c communication after the device power on,
the probability that the drivers cannot be loaded normally.
Fix the a96t346 drivers loading abnormal.
Change-Id: I6eefa6fa718d39e67cac5087816ca99552223f1c
Signed-off-by: huangjq9 <huangjq9@motorola.com>
Reviewed-on: https://gerrit.mot.com/1400568
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
Difference between ft8756 and ft8009 is only CHIP_TYPE_MAPPING,
so use ft8756 configs firstly.
Change-Id: I79f3e04bf0a31c4a94091bd8f8525b2dd87af1d7
Signed-off-by: wangyq13 <wangyq13@lenovo.com>
Reviewed-on: https://gerrit.mot.com/1399541
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Wei Deng <dengwei1@motorola.com>
Reviewed-by: Jianqi Yang <yangj@motorola.com>
Submit-Approved: Jira Key
Add option to build using clang via
USE_CLANG_FOR_MODULES. Add to the appropriate
board file for the product that needs clang.
Change-Id: I05578ac49de38887b3f359276a3350d0bb5a18db
Signed-off-by: Ryan Lattrel <ryanl@motorola.com>
Reviewed-on: https://gerrit.mot.com/1399094
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
Submit-Approved: Jira Key
This commit includes the following enhancements:
1) debug interfaces moved from Samsung specific sysfs path to I2C
device path
2) write register interface added
3) write register and erase firmware interfaces only available
in factory mode
Change-Id: I12504e99506c1a1bc76b3c9622814dbeac249438
Signed-off-by: Konstantin Makariev <hcv867@motorola.com>
Reviewed-on: https://gerrit.mot.com/1399692
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
Submit-Approved: Jira Key
QG uses the battery supply charge done property for
capacity learning, but qcom battery may not be in
charge done state when mmi charger terminates the
charging as battery is full charged.
In that case, QG will not trigger the capacity learning
when it completes a full charge cycle.
As the FULL charge state is mantained by mmi charger, so
set the charge done state once mmi charger complete charging.
Change-Id: I574e6f3349949882bb38a759835cf85a67386fb5
Signed-off-by: yanyh2 <yanyh2@motorola.com>
Reviewed-on: https://gerrit.mot.com/1396976
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Ryan Lattrel <ryanl@motorola.com>
Reviewed-by: Jianqi Yang <yangj@motorola.com>
Submit-Approved: Jira Key
Originally it was planned to do HW reset on resume. However, HW
reset was taking way to long and S.SLI suggested first to switch
to SW reset and then to simply set Normal power mode. Thus this
commit combines 2 things:
* new parameter to reset function (hw or sw)
* setting normal mode on resume
Change-Id: Ic52737f09cc7848377f91b274b47ee6dacee5204
Signed-off-by: Konstantin Makariev <hcv867@motorola.com>
Reviewed-on: https://gerrit.mot.com/1397255
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
Submit-Approved: Jira Key
When count =1 and charger also present, it will run count reset and
cancel charger check work, so add charger present condition.
Change-Id: I4a6b871cc23a18b8f9412d16f35949c610cc17e3
Signed-off-by: Haijian Ma <mahj8@motorola.com>
Reviewed-on: https://gerrit.mot.com/1396760
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Yonghua Yan <yanyh2@motorola.com>
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
Adding sysfs entry to report panel supplier name retrieved from
mmi,panel_name property of chosen device tree node. That property
gets initialized in bootloader based of results of HW detection.
Change-Id: I1c0a4ac8dc008ab8a41ae3da77cdc7ec9b2d20e2
Signed-off-by: Konstantin Makariev <hcv867@motorola.com>
Reviewed-on: https://gerrit.mot.com/1396198
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
Submit-Approved: Jira Key
There is no need to assign synaptics name to input device for
primary touch.
Mot-CRs-fixed: (CR)
This reverts commit ca0acb312a01582663d3a485f85f7a67390cf088.
Change-Id: I4d787c44b343727c9917fe7eaf036ce63bd673ad
Reviewed-on: https://gerrit.mot.com/1396206
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
Submit-Approved: Jira Key
1. sdp will config icl 100ma firstly and then config 500ma after usb
status is configuration, so normal sdp also will rerun apsd. so error sdp
can't use "icl <= 100ma" condition to check.
2. make sure charger check work call only once.
3. factory mode don't do charger check.
Change-Id: I162ca7c1ca4849a24eea3da9c38b2345b8c5f810
Signed-off-by: Haijian Ma <mahj8@motorola.com>
Reviewed-on: https://gerrit.mot.com/1395943
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
Reviewed-by: Yonghua Yan <yanyh2@motorola.com>
Unset the High Current mode if usb type is SDP or the target
icl lower is than 500mA.
If the High Current mode is set for SDP, the settled ICL may
be over the target icl value.
Change-Id: I05bb76d418c74b910eeed358e59e4b0fb3f33600
Signed-off-by: Yonghua Yan <yanyh2@motorola.com>
Reviewed-on: https://gerrit.mot.com/1394159
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Reviewed-by: Haijian Ma <mahj8@motorola.com>
Submit-Approved: Jira Key
Samsung LSI touch driver creates input device with name
samsung_mmi.primary. Framework has primary touchscreen input
name hard coded as synaptics_mmi.primary and thus won't accept
touch events from new input. This is temporary hack to allow
functional touch until CR (CR) gets resolved.
MMI_STOPSHIP
Change-Id: Ia69683d25f5216c642d86bd62e6bd29839f5b9c8
Signed-off-by: Konstantin Makariev <hcv867@motorola.com>
Reviewed-on: https://gerrit.mot.com/1394708
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
Submit-Approved: Jira Key
Probe was taking long time to fail when HW not detected due to
various delays in detection work and I2C transactions. This allowed
for resources allocation errors in another driver started
concurrently.
Change-Id: I1cb5e9c206197c8a4af3be2902a6f7f6c8249c8d
Signed-off-by: Konstantin Makariev <hcv867@motorola.com>
Reviewed-on: https://gerrit.mot.com/1395070
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
Tested-by: Jira Key
Submit-Approved: Jira Key
Reset the main and flip fuel gauges if there is a difference
of more than 15 percent between the two. This could indicate
that there is an error with the capacity value, as it
should not be physically possible for this to happen.
Change-Id: I3b74d97c1892bf1dfe537f29818dbe735f0bfa01
Signed-off-by: Ryan Lattrel <ryanl@motorola.com>
Reviewed-on: https://gerrit.mot.com/1390571
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Cesar Augusto Marcelino dos Santos <cmsantos@motorola.com>
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
Submit-Approved: Jira Key
Samsung LSI has tool accessing touch IC information via bunch
of function provided by sec device. This function was temporarily
unavailable to simplify bringup.
Change-Id: I9eb29f0ed8a52126df0a5dcfecf0d26dd5d7f5cc
Signed-off-by: Konstantin Makariev <hcv867@motorola.com>
Reviewed-on: https://gerrit.mot.com/1393553
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Konstantin Makariev <kmakariev@motorola.com>
Submit-Approved: Jira Key
Override USB ICL using the targer ICL value, so that
the ICL settled value will not be limited to a lower
value than target value.
For example, when connect device using a CC floated
typec cable, the settled icl will be set to 100mA,
which will block the charging.
Change-Id: Icd2ea3e020437297642d790f4e1fa8ab25231504
Signed-off-by: Yonghua Yan <yanyh2@motorola.com>
Reviewed-on: https://gerrit.mot.com/1393334
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Ryan Lattrel <ryanl@motorola.com>
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Reviewed-by: Haijian Ma <mahj8@motorola.com>
Reviewed-by: Jianqi Yang <yangj@motorola.com>
Submit-Approved: Jira Key
Since the firmware size of ft8756 will exceed 64K, so the CQA test
jar and ini need to be changed, at the same time have to change
touch driver to match this change.Now we need to increase size
when calling download firmware function.
Change-Id: Icea129ab53663006ebedce0af1ff0ba5b8a03f1d
Signed-off-by: wengjun1 <wengjun1@motorola.com>
Reviewed-on: https://gerrit.mot.com/1391750
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Yang Yang <yangy19@motorola.com>
Reviewed-by: Jialei Hao <haojl2@motorola.com>
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
Driver code create laser class->create virtual device->
add sys entries to this virtual device.
After laser class or virtual device create, kernel will
send add uevent to userspace.
Ueventd will received this add event and change sys entries
owner and permisions.
But ueventd thread have ran before sys entries created.
In this case, sys entries owner and permisions will not be set
correctly.
So After sys entries created, send a update uevent to userspace.
Make sure ueventd can fix sys entries permision.
Change-Id: I7b206cd99428252a8c2138083ea954211e655e6f
Signed-off-by: liuyc20 <liuyc20@lenovo.com>
Reviewed-on: https://gerrit.mot.com/1392489
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Xiaojun Ji <jixj@motorola.com>
Reviewed-by: Jun Weng <wengjun1@motorola.com>
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
The charger type based on BC1.2 detection may be wrong
at the first time when charger is attached.
Add a delay work to check the usb icl and apsd result,
and check if the usb icl is less than 100mA or apsd
is FLOAT/OCP after 10s when the apsd result changes.
This patch can fix the slow charging or no charging issue
due to slow plugin or wrong apsd result.
Change-Id: I8d02edfe4617b23c0a9f8af7251c80f733df0f71
Signed-off-by: Yonghua Yan <yanyh2@motorola.com>
Reviewed-on: https://gerrit.mot.com/1390378
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Haijian Ma <mahj8@motorola.com>
Reviewed-by: Jianqi Yang <yangj@motorola.com>
Submit-Approved: Jira Key
