commit 1ebc8e1ef906db9c08e9abe9776d85ddec837725 upstream.
Implement the workaround for erratum
3.3 RGMII timing may be out of spec when transmit delay is enabled
for the 6320 family, which says:
When transmit delay is enabled via Port register 1 bit 14 = 1, duty
cycle may be out of spec. Under very rare conditions this may cause
the attached device receive CRC errors.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: <stable@vger.kernel.org> # 5.4.x
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-8-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 172bf5a9ef70a399bb227809db78442dc01d9e48 upstream.
There is a possibility that init_codecs is invoked multiple times during
manipulated payload from video firmware. In such case, if codecs_count
can get incremented to value more than MAX_CODEC_NUM, there can be OOB
access. Reset the count so that it always starts from beginning.
Cc: stable@vger.kernel.org
Fixes: 1a73374a04 ("media: venus: hfi_parser: add common capability parser")
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d391292cdd53984ec1b9a1f6182a62a62751e03 upstream.
Lift the xshutdown (enable) GPIO 1 ms after enabling the regulators, as
required by the sensor's power-up sequence.
Fixes: d30bb512da ("media: Add a driver for the ov7251 camera sensor")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1963698d59cec83df640ded343af08b76c8e9c5 upstream.
Set the enable GPIO low when acquiring it.
Fixes: d30bb512da ("media: Add a driver for the ov7251 camera sensor")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3edd1fc48d2c045e8259561797c89fe78f01717e upstream.
In v4l2_detect_gtf(), it seems safer to cast the 32-bit image_width
variable to the 64-bit type u64 before multiplying to avoid
a possible overflow. The resulting object code even seems to
look better, at least on x86_64.
Found by Linux Verification Center (linuxtesting.org) with Svace.
[Sergey: rewrote the patch subject/descripition]
Fixes: c9bc9f5075 ("[media] v4l2-dv-timings: fix overflow in gtf timings calculation")
Cc: stable@vger.kernel.org
Signed-off-by: Karina Yankevich <k.yankevich@omp.ru>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 549f6d348167fb2f7800ed7c8d4bce9630c74498 upstream.
If streamzap_callback() receives an urb with any non-critical error
status, i.e. any error code other than -ECONNRESET, -ENOENT or -ESHUTDOWN,
it will try to process IR data, ignoring a possible transfer failure.
Make streamzap_callback() process IR data only when urb->status is 0.
Move processing logic to a separate function to make code cleaner and
more similar to the URB completion handlers in other RC drivers.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 19770693c3 ("V4L/DVB: staging/lirc: add lirc_streamzap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Murad Masimov <m.masimov@mt-integration.ru>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9b5bd81b294d30a747edd125e9f6aef2def7c79 upstream.
>From the TRM, MIDR_CORTEX_A76AE has a partnum of 0xDOE and an
implementor of 0x41 (ARM). Add the values.
Cc: stable@vger.kernel.org # dependency of the next fix in the series
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250107120555.v4.4.I151f3b7ee323bcc3082179b8c60c3cd03308aa94@changeid
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c4e79e29a9fe4ea132118ac40c2bc97cfe23077 upstream.
The interface specifies the symnum field as an input and output; the
hypervisor sets it to the next sequential symbol's index. xensyms_next()
incrementing the position explicitly (and xensyms_next_sym()
decrementing it to "rewind") is only correct as long as the sequence of
symbol indexes is non-sparse. Use the hypervisor-supplied value instead
to update the position in xensyms_next(), and use the saved incoming
index in xensyms_next_sym().
Cc: stable@kernel.org
Fixes: a11f4f0a4e ("xen: xensyms support")
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Message-ID: <15d5e7fa-ec5d-422f-9319-d28bed916349@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 734ac57e47b3bdd140a1119e2c4e8e6f8ef8b33d upstream.
The smsdvb_module_init() returns without checking the retval from
smscore_register_hotplug().
If the smscore_register_hotplug() failed, the module failed to install,
leaving the smsdvb_debugfs not unregistered.
Fixes: 3f6b87cff6 ("[media] siano: allow showing the complete statistics via debugfs")
Cc: stable@vger.kernel.org
Signed-off-by: Yuan Can <yuancan@huawei.com>
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69baf245b23e20efda0079238b27fc63ecf13de1 upstream.
qsize represents size of shared queued between driver and video
firmware. Firmware can modify this value to an invalid large value. In
such situation, empty_space will be bigger than the space actually
available. Since new_wr_idx is not checked, so the following code will
result in an OOB write.
...
qsize = qhdr->q_size
if (wr_idx >= rd_idx)
empty_space = qsize - (wr_idx - rd_idx)
....
if (new_wr_idx < qsize) {
memcpy(wr_ptr, packet, dwords << 2) --> OOB write
Add check to ensure qsize is within the allocated size while
reading and writing packets into the queue.
Cc: stable@vger.kernel.org
Fixes: d96d3f30c0 ("[media] media: venus: hfi: add Venus HFI files")
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4b211714bcc70effa60c34d9fa613d182e3ef1e upstream.
sfr->buf_size is in shared memory and can be modified by malicious user.
OOB write is possible when the size is made higher than actual sfr data
buffer. Cap the size to allocated size for such cases.
Cc: stable@vger.kernel.org
Fixes: d96d3f30c0 ("[media] media: venus: hfi: add Venus HFI files")
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e38acacb9d809b97a0bdc5c76e725355a47158a upstream.
The mask to select the test-pattern in register ADV748X_SDP_FRP is
incorrect, it's the lower 3 bits which controls the pattern. The
GENMASK() macro is used incorrectly and the generated mask is 0x0e
instead of 0x07.
The result is that not all test patterns are selectable, and that in
some cases the wrong test pattern is activated. Fix this by correcting
the GENMASK().
Fixes: 3e89586a64 ("media: i2c: adv748x: add adv748x driver")
Cc: stable@vger.kernel.org
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
[hverkuil: fixed tiny typo in commit log: my -> by]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 642335f3ea2b3fd6dba03e57e01fa9587843a497 ]
A file handle that userspace provides to open_by_handle_at() can
legitimately contain an outdated inode number that has since been reused
for another purpose - that's why the file handle also contains a generation
number.
But if the inode number has been reused for an ea_inode, check_igot_inode()
will notice, __ext4_iget() will go through ext4_error_inode(), and if the
inode was newly created, it will also be marked as bad by iget_failed().
This all happens before the point where the inode generation is checked.
ext4_error_inode() is supposed to only be used on filesystem corruption; it
should not be used when userspace just got unlucky with a stale file
handle. So when this happens, let __ext4_iget() just return an error.
Fixes: b3e6bcb94590 ("ext4: add EA_INODE checking to ext4_iget()")
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20241129-ext4-ignore-ea-fhandle-v1-1-e532c0d1cee0@google.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8216776ccff6fcd40e3fdaa109aa4150ebe760b3 ]
It is invalid for the casefold inode flag to be set without the casefold
superblock feature flag also being set. e2fsck already considers this
case to be invalid and handles it by offering to clear the casefold flag
on the inode. __ext4_iget() also already considered this to be invalid,
sort of, but it only got so far as logging an error message; it didn't
actually reject the inode. Make it reject the inode so that other code
doesn't have to handle this case. This matches what f2fs does.
Note: we could check 's_encoding != NULL' instead of
ext4_has_feature_casefold(). This would make the check robust against
the casefold feature being enabled by userspace writing to the page
cache of the mounted block device. However, it's unsolvable in general
for filesystems to be robust against concurrent writes to the page cache
of the mounted block device. Though this very particular scenario
involving the casefold feature is solvable, we should not pretend that
we can support this model, so let's just check the casefold feature.
tune2fs already forbids enabling casefold on a mounted filesystem.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20230814182903.37267-2-ebiggers@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 642335f3ea2b ("ext4: don't treat fhandle lookup of ea_inode as FS corruption")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4bac0288a2b444e468e6df9cb4ed69479ddf14a ]
Classic BPF socket filters with SKB_NET_OFF and SKB_LL_OFF fail to
read when these offsets extend into frags.
This has been observed with iwlwifi and reproduced with tun with
IFF_NAPI_FRAGS. The below straightforward socket filter on UDP port,
applied to a RAW socket, will silently miss matching packets.
const int offset_proto = offsetof(struct ip6_hdr, ip6_nxt);
const int offset_dport = sizeof(struct ip6_hdr) + offsetof(struct udphdr, dest);
struct sock_filter filter_code[] = {
BPF_STMT(BPF_LD + BPF_B + BPF_ABS, SKF_AD_OFF + SKF_AD_PKTTYPE),
BPF_JUMP(BPF_JMP + BPF_JEQ + BPF_K, PACKET_HOST, 0, 4),
BPF_STMT(BPF_LD + BPF_B + BPF_ABS, SKF_NET_OFF + offset_proto),
BPF_JUMP(BPF_JMP + BPF_JEQ + BPF_K, IPPROTO_UDP, 0, 2),
BPF_STMT(BPF_LD + BPF_H + BPF_ABS, SKF_NET_OFF + offset_dport),
This is unexpected behavior. Socket filter programs should be
consistent regardless of environment. Silent misses are
particularly concerning as hard to detect.
Use skb_copy_bits for offsets outside linear, same as done for
non-SKF_(LL|NET) offsets.
Offset is always positive after subtracting the reference threshold
SKB_(LL|NET)_OFF, so is always >= skb_(mac|network)_offset. The sum of
the two is an offset against skb->data, and may be negative, but it
cannot point before skb->head, as skb_(mac|network)_offset would too.
This appears to go back to when frag support was introduced to
sk_run_filter in linux-2.4.4, before the introduction of git.
The amount of code change and 8/16/32 bit duplication are unfortunate.
But any attempt I made to be smarter saved very few LoC while
complicating the code.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/netdev/20250122200402.3461154-1-maze@google.com/
Link: https://elixir.bootlin.com/linux/2.4.4/source/net/core/filter.c#L244
Reported-by: Matt Moeller <moeller.matt@gmail.com>
Co-developed-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://lore.kernel.org/r/20250408132833.195491-2-willemdebruijn.kernel@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96a233e600df351bcb06e3c20efe048855552926 ]
A couple of the syscalls which load values (bpf_skb_load_helper_16() and
bpf_skb_load_helper_32()) are using u16/u32 types which are triggering
warnings as they are then converted from big-endian to CPU-endian. Fix
these by making the types __be instead.
Fixes the following sparse warnings:
net/core/filter.c:246:32: warning: cast to restricted __be16
net/core/filter.c:246:32: warning: cast to restricted __be16
net/core/filter.c:246:32: warning: cast to restricted __be16
net/core/filter.c:246:32: warning: cast to restricted __be16
net/core/filter.c:273:32: warning: cast to restricted __be32
net/core/filter.c:273:32: warning: cast to restricted __be32
net/core/filter.c:273:32: warning: cast to restricted __be32
net/core/filter.c:273:32: warning: cast to restricted __be32
net/core/filter.c:273:32: warning: cast to restricted __be32
net/core/filter.c:273:32: warning: cast to restricted __be32
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220714105101.297304-1-ben.dooks@sifive.com
Stable-dep-of: d4bac0288a2b ("bpf: support SKF_NET_OFF and SKF_LL_OFF on skb frags")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 928446a5302eee30ebb32075c0db5dda5a138fb7 ]
Considering that the driver doesn't enable the used clocks (and also
that clk_get_rate() returns 0 if CONFIG_HAVE_CLK is unset) better check
the return value of clk_get_rate() for being non-zero before dividing by
it.
Fixes: 3479bbd1e1 ("pwm: fsl-ftm: More relaxed permissions for updating period")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/b68351a51017035651bc62ad3146afcb706874f0.1743501688.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ca59947b5fcf94e7ea4029d1bd0f7c41500a161 ]
With CONFIG_COMPILE_TEST && !CONFIG_HAVE_CLK, pwm_mediatek_config() has a
divide-by-zero in the following line:
do_div(resolution, clk_get_rate(pc->clk_pwms[pwm->hwpwm]));
due to the fact that the !CONFIG_HAVE_CLK version of clk_get_rate()
returns zero.
This is presumably just a theoretical problem: COMPILE_TEST overrides
the dependency on RALINK which would select COMMON_CLK. Regardless it's
a good idea to check for the error explicitly to avoid divide-by-zero.
Fixes the following warning:
drivers/pwm/pwm-mediatek.o: warning: objtool: .text: unexpected end of section
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://lore.kernel.org/r/fb56444939325cc173e752ba199abd7aeae3bf12.1742852847.git.jpoimboe@kernel.org
[ukleinek: s/CONFIG_CLK/CONFIG_HAVE_CLK/]
Fixes: caf065f8fd ("pwm: Add MediaTek PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/9e78a0796acba3435553ed7db1c7965dcffa6215.1743501688.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c0ead76235db0bcfaab83f04db546995449d002 ]
The MediaTek PWM IP can sometimes use the 26 MHz source clock to
generate the PWM signal, but the driver currently assumes that we always
use the PWM bus clock to generate the PWM signal.
This commit modifies the PWM driver in order to force the PWM IP to
always use the bus clock as source clock.
I do not have the datasheet of all the MediaTek SoC, so I don't know if
the register to choose the source clock is present in all the SoCs or
only in subset. As a consequence I made this change optional by using a
platform data paremeter to says whether this register is supported or
not. On all the SoCs I don't have the datasheet (MT2712, MT7622, MT7623,
MT7628, MT7629) I kept the behavior to be the same as before this
change.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Stable-dep-of: 7ca59947b5fc ("pwm: mediatek: Prevent divide-by-zero in pwm_mediatek_config()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e411827f31db7f938a30a3c7a7599839401ec30 ]
Function dispc_ovl_setup is not intended to work with the value OMAP_DSS_WB
of the enum parameter plane.
The value of this parameter is initialized in dss_init_overlays and in the
current state of the code it cannot take this value so it's not a real
problem.
For the purposes of defensive coding it wouldn't be superfluous to check
the parameter value, because some functions down the call stack process
this value correctly and some not.
For example, in dispc_ovl_setup_global_alpha it may lead to buffer
overflow.
Add check for this value.
Found by Linux Verification Center (linuxtesting.org) with SVACE static
analysis tool.
Signed-off-by: Leonid Arapov <arapovl839@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 473c33f5ce651365468503c76f33158aaa1c7dd2 ]
In preparation for adding support for MT8195's HDMI reserved
DPI, add calls to clk_prepare_enable() / clk_disable_unprepare()
for the TVD clock: in this particular case, the aforementioned
clock is not (and cannot be) parented to neither pixel or engine
clocks hence it won't get enabled automatically by the clock
framework.
Please note that on all of the currently supported MediaTek
platforms, the TVD clock is always a parent of either pixel or
engine clocks, and this means that the common clock framework
is already enabling this clock before the children.
On such platforms, this commit will only increase the refcount
of the TVD clock without any functional change.
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250217154836.108895-10-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7919b4cad5545ed93778f11881ceee72e4dbed66 ]
If GPU in reset, destroy_queue return -EIO, pqm_destroy_queue should
delete the queue from process_queue_list and free the resource.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e90711946b53590371ecce32e8fcc381a99d6333 ]
If queue size is less than minimum, clamp it to minimum to prevent
underflow when writing queue mqd.
Signed-off-by: David Yat Sin <David.YatSin@amd.com>
Reviewed-by: Jay Cornwall <jay.cornwall@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a860eb9c6ba6cdbf32e3e01a606556e5a90a2931 ]
Some GPD Win 2 units shipped with the correct DMI strings.
Add a DMI match to correctly rotate the panel on these units.
Signed-off-by: Andrew Wyatt <fewtarius@steamfork.org>
Signed-off-by: John Edwards <uejji@uejji.net>
Tested-by: Paco Avelar <pacoavelar@hotmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250213222455.93533-5-uejji@uejji.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb8f1e3e8ee10cff591d4a47437dfd34d850d454 ]
AYANEO 2S uses the same panel and orientation as the AYANEO 2.
Update the AYANEO 2 DMI match to also match AYANEO 2S.
Signed-off-by: Andrew Wyatt <fewtarius@steamfork.org>
Signed-off-by: John Edwards <uejji@uejji.net>
Tested-by: John Edwards <uejji@uejji.net>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250213222455.93533-2-uejji@uejji.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e182cb4f5567f53417b762ec0d679f0b6f0039d ]
In certain use-cases, a CRTC could switch between two encoders
and because the mode being programmed on the CRTC remains
the same during this switch, the CRTC's mode_changed remains false.
In such cases, the encoder's mode_set also gets skipped.
Skipping mode_set on the encoder for such cases could cause an issue
because even though the same CRTC mode was being used, the encoder
type could have changed like the CRTC could have switched from a
real time encoder to a writeback encoder OR vice-versa.
Allow encoder's mode_set to happen even when connectors changed on a
CRTC and not just when the mode changed.
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241211-abhinavk-modeset-fix-v3-1-0de4bf3e7c32@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 366ceff495f902182d42b6f41525c2474caf3f9a ]
'hci_register_dev()' calls power up function, which is executed by
kworker - 'hci_power_on()'. This function does access to bluetooth chip
using callbacks from 'hci_ldisc.c', for example 'hci_uart_send_frame()'.
Now 'hci_uart_send_frame()' checks 'HCI_UART_PROTO_READY' bit set, and
if not - it fails. Problem is that 'HCI_UART_PROTO_READY' is set after
'hci_register_dev()', and there is tiny chance that 'hci_power_on()' will
be executed before setting this bit. In that case HCI init logic fails.
Patch moves setting of 'HCI_UART_PROTO_READY' before calling function
'hci_uart_register_dev()'.
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c588ac0ca6c22b774d9ad4a6594681fdfa57d9d ]
When __ftrace_event_enable_disable invokes the class callback to
unregister the event, the return value is not reported up to the
caller, hence leading to event unregister failures being silently
ignored.
This patch assigns the ret variable to the invocation of the
event unregister callback, so that its return value is stored
and reported to the caller, and it raises a warning in case
of error.
Link: https://lore.kernel.org/20250321170821.101403-1-gpaoloni@redhat.com
Signed-off-by: Gabriele Paoloni <gpaoloni@redhat.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27b918007d96402aba10ed52a6af8015230f1793 ]
With the device instance lock, there is now a possibility of a deadlock:
[ 1.211455] ============================================
[ 1.211571] WARNING: possible recursive locking detected
[ 1.211687] 6.14.0-rc5-01215-g032756b4ca7a-dirty #5 Not tainted
[ 1.211823] --------------------------------------------
[ 1.211936] ip/184 is trying to acquire lock:
[ 1.212032] ffff8881024a4c30 (&dev->lock){+.+.}-{4:4}, at: dev_set_allmulti+0x4e/0xb0
[ 1.212207]
[ 1.212207] but task is already holding lock:
[ 1.212332] ffff8881024a4c30 (&dev->lock){+.+.}-{4:4}, at: dev_open+0x50/0xb0
[ 1.212487]
[ 1.212487] other info that might help us debug this:
[ 1.212626] Possible unsafe locking scenario:
[ 1.212626]
[ 1.212751] CPU0
[ 1.212815] ----
[ 1.212871] lock(&dev->lock);
[ 1.212944] lock(&dev->lock);
[ 1.213016]
[ 1.213016] *** DEADLOCK ***
[ 1.213016]
[ 1.213143] May be due to missing lock nesting notation
[ 1.213143]
[ 1.213294] 3 locks held by ip/184:
[ 1.213371] #0: ffffffff838b53e0 (rtnl_mutex){+.+.}-{4:4}, at: rtnl_nets_lock+0x1b/0xa0
[ 1.213543] #1: ffffffff84e5fc70 (&net->rtnl_mutex){+.+.}-{4:4}, at: rtnl_nets_lock+0x37/0xa0
[ 1.213727] #2: ffff8881024a4c30 (&dev->lock){+.+.}-{4:4}, at: dev_open+0x50/0xb0
[ 1.213895]
[ 1.213895] stack backtrace:
[ 1.213991] CPU: 0 UID: 0 PID: 184 Comm: ip Not tainted 6.14.0-rc5-01215-g032756b4ca7a-dirty #5
[ 1.213993] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014
[ 1.213994] Call Trace:
[ 1.213995] <TASK>
[ 1.213996] dump_stack_lvl+0x8e/0xd0
[ 1.214000] print_deadlock_bug+0x28b/0x2a0
[ 1.214020] lock_acquire+0xea/0x2a0
[ 1.214027] __mutex_lock+0xbf/0xd40
[ 1.214038] dev_set_allmulti+0x4e/0xb0 # real_dev->flags & IFF_ALLMULTI
[ 1.214040] vlan_dev_open+0xa5/0x170 # ndo_open on vlandev
[ 1.214042] __dev_open+0x145/0x270
[ 1.214046] __dev_change_flags+0xb0/0x1e0
[ 1.214051] netif_change_flags+0x22/0x60 # IFF_UP vlandev
[ 1.214053] dev_change_flags+0x61/0xb0 # for each device in group from dev->vlan_info
[ 1.214055] vlan_device_event+0x766/0x7c0 # on netdevsim0
[ 1.214058] notifier_call_chain+0x78/0x120
[ 1.214062] netif_open+0x6d/0x90
[ 1.214064] dev_open+0x5b/0xb0 # locks netdevsim0
[ 1.214066] bond_enslave+0x64c/0x1230
[ 1.214075] do_set_master+0x175/0x1e0 # on netdevsim0
[ 1.214077] do_setlink+0x516/0x13b0
[ 1.214094] rtnl_newlink+0xaba/0xb80
[ 1.214132] rtnetlink_rcv_msg+0x440/0x490
[ 1.214144] netlink_rcv_skb+0xeb/0x120
[ 1.214150] netlink_unicast+0x1f9/0x320
[ 1.214153] netlink_sendmsg+0x346/0x3f0
[ 1.214157] __sock_sendmsg+0x86/0xb0
[ 1.214160] ____sys_sendmsg+0x1c8/0x220
[ 1.214164] ___sys_sendmsg+0x28f/0x2d0
[ 1.214179] __x64_sys_sendmsg+0xef/0x140
[ 1.214184] do_syscall_64+0xec/0x1d0
[ 1.214190] entry_SYSCALL_64_after_hwframe+0x77/0x7f
[ 1.214191] RIP: 0033:0x7f2d1b4a7e56
Device setup:
netdevsim0 (down)
^ ^
bond netdevsim1.100@netdevsim1 allmulticast=on (down)
When we enslave the lower device (netdevsim0) which has a vlan, we
propagate vlan's allmuti/promisc flags during ndo_open. This causes
(re)locking on of the real_dev.
Propagate allmulti/promisc on flags change, not on the open. There
is a slight semantics change that vlans that are down now propagate
the flags, but this seems unlikely to result in the real issues.
Reproducer:
echo 0 1 > /sys/bus/netdevsim/new_device
dev_path=$(ls -d /sys/bus/netdevsim/devices/netdevsim0/net/*)
dev=$(echo $dev_path | rev | cut -d/ -f1 | rev)
ip link set dev $dev name netdevsim0
ip link set dev netdevsim0 up
ip link add link netdevsim0 name netdevsim0.100 type vlan id 100
ip link set dev netdevsim0.100 allmulticast on down
ip link add name bond1 type bond mode 802.3ad
ip link set dev netdevsim0 down
ip link set dev netdevsim0 master bond1
ip link set dev bond1 up
ip link show
Reported-by: syzbot+b0c03d76056ef6cd12a6@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/Z9CfXjLMKn6VLG5d@mini-arch/T/#m15ba130f53227c883e79fb969687d69d670337a0
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250313100657.2287455-1-sdf@fomichev.me
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06cccc2ebbe6c8a20f714f3a0ff3ff489d3004bb ]
The TP-Link TL-WDN6200 "Driverless" version cards use a MT7612U chipset.
Add the USB ID to mt76x2u driver.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Link: https://patch.msgid.link/20250317102235.1421726-1-uwu@icenowy.me
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 530fea29ef82e169cd7fe048c2b7baaeb85a0028 ]
Protect ext4_release_dquot against freezing so that we
don't try to start a transaction when FS is frozen, leading
to warnings.
Further, avoid taking the freeze protection if a transaction
is already running so that we don't need end up in a deadlock
as described in
46e294efc355 ext4: fix deadlock with fs freezing and EA inodes
Suggested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20241121123855.645335-3-ojaswin@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 885251dc35767b1c992f6909532ca366c830814a ]
Add support for Marvell Technology Group Ltd. 88SE9215 SATA 6 Gb/s
controller, which is e.g. used in the DAWICONTROL DC-614e RAID bus
controller and was not automatically recognized before.
Tested with a DAWICONTROL DC-614e RAID bus controller.
Signed-off-by: Daniel Kral <d.kral@proxmox.com>
Link: https://lore.kernel.org/r/20250304092030.37108-1-d.kral@proxmox.com
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91ec84f8eaddbc93d7c62e363d68aeb7b89879c7 ]
atapi_eh_request_sense() currently uses ATAPI DMA if the SATA controller
has ATA_FLAG_PIO_DMA (PIO cmds via DMA) set.
However, ATA_FLAG_PIO_DMA is a flag that can be set by a low-level driver
on a port at initialization time, before any devices are scanned.
If a controller detects a connected device that only supports PIO, we set
the flag ATA_DFLAG_PIO.
Modify atapi_eh_request_sense() to not use ATAPI DMA if the connected
device only supports PIO.
Reported-by: Philip Pemberton <lists@philpem.me.uk>
Closes: https://lore.kernel.org/linux-ide/c6722ee8-5e21-4169-af59-cbbae9edc02f@philpem.me.uk/
Tested-by: Philip Pemberton <lists@philpem.me.uk>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20250221015422.20687-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddf2846f22e8575d6b4b6a66f2100f168b8cd73d ]
The width in dmapctl of the AG is zero, it trigger a divide error when
calculating the control page level in dbAllocAG.
To avoid this issue, add a check for agwidth in dbAllocAG.
Reported-and-tested-by: syzbot+7c808908291a569281a9@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=7c808908291a569281a9
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b61e69bb1c049cf507e3c654fa3dc1568231bd07 ]
syzbot report a deadlock in diFree. [1]
When calling "ioctl$LOOP_SET_STATUS64", the offset value passed in is 4,
which does not match the mounted loop device, causing the mapping of the
mounted loop device to be invalidated.
When creating the directory and creating the inode of iag in diReadSpecial(),
read the page of fixed disk inode (AIT) in raw mode in read_metapage(), the
metapage data it returns is corrupted, which causes the nlink value of 0 to be
assigned to the iag inode when executing copy_from_dinode(), which ultimately
causes a deadlock when entering diFree().
To avoid this, first check the nlink value of dinode before setting iag inode.
[1]
WARNING: possible recursive locking detected
6.12.0-rc7-syzkaller-00212-g4a5df3796467 #0 Not tainted
--------------------------------------------
syz-executor301/5309 is trying to acquire lock:
ffff888044548920 (&(imap->im_aglock[index])){+.+.}-{3:3}, at: diFree+0x37c/0x2fb0 fs/jfs/jfs_imap.c:889
but task is already holding lock:
ffff888044548920 (&(imap->im_aglock[index])){+.+.}-{3:3}, at: diAlloc+0x1b6/0x1630
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(imap->im_aglock[index]));
lock(&(imap->im_aglock[index]));
*** DEADLOCK ***
May be due to missing lock nesting notation
5 locks held by syz-executor301/5309:
#0: ffff8880422a4420 (sb_writers#9){.+.+}-{0:0}, at: mnt_want_write+0x3f/0x90 fs/namespace.c:515
#1: ffff88804755b390 (&type->i_mutex_dir_key#6/1){+.+.}-{3:3}, at: inode_lock_nested include/linux/fs.h:850 [inline]
#1: ffff88804755b390 (&type->i_mutex_dir_key#6/1){+.+.}-{3:3}, at: filename_create+0x260/0x540 fs/namei.c:4026
#2: ffff888044548920 (&(imap->im_aglock[index])){+.+.}-{3:3}, at: diAlloc+0x1b6/0x1630
#3: ffff888044548890 (&imap->im_freelock){+.+.}-{3:3}, at: diNewIAG fs/jfs/jfs_imap.c:2460 [inline]
#3: ffff888044548890 (&imap->im_freelock){+.+.}-{3:3}, at: diAllocExt fs/jfs/jfs_imap.c:1905 [inline]
#3: ffff888044548890 (&imap->im_freelock){+.+.}-{3:3}, at: diAllocAG+0x4b7/0x1e50 fs/jfs/jfs_imap.c:1669
#4: ffff88804755a618 (&jfs_ip->rdwrlock/1){++++}-{3:3}, at: diNewIAG fs/jfs/jfs_imap.c:2477 [inline]
#4: ffff88804755a618 (&jfs_ip->rdwrlock/1){++++}-{3:3}, at: diAllocExt fs/jfs/jfs_imap.c:1905 [inline]
#4: ffff88804755a618 (&jfs_ip->rdwrlock/1){++++}-{3:3}, at: diAllocAG+0x869/0x1e50 fs/jfs/jfs_imap.c:1669
stack backtrace:
CPU: 0 UID: 0 PID: 5309 Comm: syz-executor301 Not tainted 6.12.0-rc7-syzkaller-00212-g4a5df3796467 #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120
print_deadlock_bug+0x483/0x620 kernel/locking/lockdep.c:3037
check_deadlock kernel/locking/lockdep.c:3089 [inline]
validate_chain+0x15e2/0x5920 kernel/locking/lockdep.c:3891
__lock_acquire+0x1384/0x2050 kernel/locking/lockdep.c:5202
lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5825
__mutex_lock_common kernel/locking/mutex.c:608 [inline]
__mutex_lock+0x136/0xd70 kernel/locking/mutex.c:752
diFree+0x37c/0x2fb0 fs/jfs/jfs_imap.c:889
jfs_evict_inode+0x32d/0x440 fs/jfs/inode.c:156
evict+0x4e8/0x9b0 fs/inode.c:725
diFreeSpecial fs/jfs/jfs_imap.c:552 [inline]
duplicateIXtree+0x3c6/0x550 fs/jfs/jfs_imap.c:3022
diNewIAG fs/jfs/jfs_imap.c:2597 [inline]
diAllocExt fs/jfs/jfs_imap.c:1905 [inline]
diAllocAG+0x17dc/0x1e50 fs/jfs/jfs_imap.c:1669
diAlloc+0x1d2/0x1630 fs/jfs/jfs_imap.c:1590
ialloc+0x8f/0x900 fs/jfs/jfs_inode.c:56
jfs_mkdir+0x1c5/0xba0 fs/jfs/namei.c:225
vfs_mkdir+0x2f9/0x4f0 fs/namei.c:4257
do_mkdirat+0x264/0x3a0 fs/namei.c:4280
__do_sys_mkdirat fs/namei.c:4295 [inline]
__se_sys_mkdirat fs/namei.c:4293 [inline]
__x64_sys_mkdirat+0x87/0xa0 fs/namei.c:4293
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Reported-by: syzbot+355da3b3a74881008e8f@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=355da3b3a74881008e8f
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fcbf789629cdb9fbf4e2172ce31136cfed11e5e ]
The JFS filesystem calculates allocation group (AG) size using 1 <<
l2agsize in dbExtendFS(). When l2agsize exceeds 31 (possible with >2TB
aggregates on 32-bit systems), this 32-bit shift operation causes undefined
behavior and improper AG sizing.
On 32-bit architectures:
- Left-shifting 1 by 32+ bits results in 0 due to integer overflow
- This creates invalid AG sizes (0 or garbage values) in
sbi->bmap->db_agsize
- Subsequent block allocations would reference invalid AG structures
- Could lead to:
- Filesystem corruption during extend operations
- Kernel crashes due to invalid memory accesses
- Security vulnerabilities via malformed on-disk structures
Fix by casting to s64 before shifting:
bmp->db_agsize = (s64)1 << l2agsize;
This ensures 64-bit arithmetic even on 32-bit architectures. The cast
matches the data type of db_agsize (s64) and follows similar patterns in
JFS block calculation code.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rand Deeb <rand.sec96@gmail.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70ca3246ad201b53a9f09380b3f29d8bac320383 ]
The expression "inactags << bmp->db_agl2size" in the function
dbFinalizeBmap() is computed using int operands. Although the
values (inactags and db_agl2size) are derived from filesystem
parameters and are usually small, there is a theoretical risk that
the shift could overflow a 32-bit int if extreme values occur.
According to the C standard, shifting a signed 32-bit int can lead
to undefined behavior if the result exceeds its range. In our
case, an overflow could miscalculate free blocks, potentially
leading to erroneous filesystem accounting.
To ensure the arithmetic is performed in 64-bit space, we cast
"inactags" to s64 before shifting. This defensive fix prevents any
risk of overflow and complies with kernel coding best practices.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rand Deeb <rand.sec96@gmail.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43130d02baa137033c25297aaae95fd0edc41654 ]
We noticed the kworker in page_pool_release_retry() was waken
up repeatedly and infinitely in production because of the
buggy driver causing the inflight less than 0 and warning
us in page_pool_inflight()[1].
Since the inflight value goes negative, it means we should
not expect the whole page_pool to get back to work normally.
This patch mitigates the adverse effect by not rescheduling
the kworker when detecting the inflight negative in
page_pool_release_retry().
[1]
[Mon Feb 10 20:36:11 2025] ------------[ cut here ]------------
[Mon Feb 10 20:36:11 2025] Negative(-51446) inflight packet-pages
...
[Mon Feb 10 20:36:11 2025] Call Trace:
[Mon Feb 10 20:36:11 2025] page_pool_release_retry+0x23/0x70
[Mon Feb 10 20:36:11 2025] process_one_work+0x1b1/0x370
[Mon Feb 10 20:36:11 2025] worker_thread+0x37/0x3a0
[Mon Feb 10 20:36:11 2025] kthread+0x11a/0x140
[Mon Feb 10 20:36:11 2025] ? process_one_work+0x370/0x370
[Mon Feb 10 20:36:11 2025] ? __kthread_cancel_work+0x40/0x40
[Mon Feb 10 20:36:11 2025] ret_from_fork+0x35/0x40
[Mon Feb 10 20:36:11 2025] ---[ end trace ebffe800f33e7e34 ]---
Note: before this patch, the above calltrace would flood the
dmesg due to repeated reschedule of release_dw kworker.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250214064250.85987-1-kerneljasonxing@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2820405ba55a38932aa2177f026b70064296663 ]
Fix quirk for CME master keyboards so it not only handles
sysex but also song position pointer, MIDI timing clock, start
and stop messages, and active sensing. All of these can be
output by the CME UF series master keyboards.
Tested with a CME UF6 in a desktop Linux environment as
well as on the Zynthian Raspberry Pi based platform.
Signed-off-by: Ricard Wanderlof <ricard2013@butoba.net>
Link: https://patch.msgid.link/20250313-cme-fix-v1-1-d404889e4de8@butoba.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b360ba9a4936486380bc30d1eabceb40a714d98 ]
quirk_nvidia_hda() forcefully enables HDA controller on all NVIDIA GPUs,
because some buggy BIOSes leave it disabled. However, some dual-GPU
laptops do not have a functional HDA controller in DGPU, and BIOS
disables it on purpose. After quirk_nvidia_hda() reenables this dummy
HDA controller, attempting to probe it fails at azx_first_init(), which
is too late to cancel the probe, as it happens in azx_probe_continue().
The sna_hda_intel driver calls azx_free() and stops the chip, however,
it stays probed, and from the runtime PM point of view, the device
remains active (it was set as active by the PCI subsystem on probe). It
prevents vga_switcheroo from turning off the DGPU, because
pci_create_device_link() syncs power management for video and audio
devices.
Affected devices should be added to driver_denylist to prevent them from
probing early. This patch helps identify such devices by printing a
warning, and also forces the device to the suspended state to allow
vga_switcheroo turn off DGPU.
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Link: https://patch.msgid.link/20250208214602.39607-2-maxtram95@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22a05462c3d0eee15154faf8d13c49e6295270a5 ]
This function triggered a null pointer dereference if used to search for
a report that isn't implemented on the device. This happened both for
optional and required reports alike.
The same logic was applied to pidff_find_special_field and although
pidff_init_fields should return an error earlier if one of the required
reports is missing, future modifications could change this logic and
resurface this possible null pointer dereference again.
LKML bug report:
https://lore.kernel.org/all/CAL-gK7f5=R0nrrQdPtaZZr1fd-cdAMbDMuZ_NLA8vM0SX+nGSw@mail.gmail.com
Reported-by: Nolan Nicholson <nolananicholson@gmail.com>
Signed-off-by: Tomasz Pakuła <tomasz.pakula.oficjalny@gmail.com>
Reviewed-by: Michał Kopeć <michal@nozomi.space>
Reviewed-by: Paul Dino Jones <paul@spacefreak18.xyz>
Tested-by: Paul Dino Jones <paul@spacefreak18.xyz>
Tested-by: Cristóferson Bueno <cbueno81@gmail.com>
Tested-by: Pablo Cisneros <patchkez@protonmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8876fc1884f5b39550c8387ff3176396c988541d ]
Envelope struct is always initialized, but the envelope itself is
optional as described in USB PID Device class definition 1.0.
5.1.1.1 Type Specific Block Offsets
...
4) Effects that do not use Condition Blocks use 1 Parameter Block and
an *optional* Envelope Block.
Sending out "empty" envelope breaks force feedback on some devices with
games that use SINE effect + offset to emulate constant force effect, as
well as generally breaking Constant/Periodic effects. One of the affected
brands is Moza Racing.
This change prevents the envelope from being sent if it contains all
0 values while keeping the old behavior of only sending it, if it differs
from the old one.
Changes in v6:
- Simplify the checks to make them clearer
- Fix possible null pointer dereference while calling
pidff_needs_set_envelope
Signed-off-by: Tomasz Pakuła <tomasz.pakula.oficjalny@gmail.com>
Reviewed-by: Michał Kopeć <michal@nozomi.space>
Reviewed-by: Paul Dino Jones <paul@spacefreak18.xyz>
Tested-by: Paul Dino Jones <paul@spacefreak18.xyz>
Tested-by: Cristóferson Bueno <cbueno81@gmail.com>
Tested-by: Pablo Cisneros <patchkez@protonmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37e0591fe44dce39d1ebc7a82d5b6e4dba1582eb ]
Software uses 0 as de-facto infinite lenght on Linux FF apis (SDL),
Linux doesn't actually define anythi as of now, while USB PID defines
NULL (0xffff). Most PID devices do not expect a 0-length effect and
can't interpret it as infinite. This change fixes Force Feedback for
most PID compliant devices.
As most games depend on updating the values of already playing infinite
effects, this is crucial to ensure they will actually work.
Previously, users had to rely on third-party software to do this conversion
and make their PID devices usable.
Co-developed-by: Makarenko Oleg <oleg@makarenk.ooo>
Signed-off-by: Makarenko Oleg <oleg@makarenk.ooo>
Signed-off-by: Tomasz Pakuła <tomasz.pakula.oficjalny@gmail.com>
Reviewed-by: Michał Kopeć <michal@nozomi.space>
Reviewed-by: Paul Dino Jones <paul@spacefreak18.xyz>
Tested-by: Paul Dino Jones <paul@spacefreak18.xyz>
Tested-by: Cristóferson Bueno <cbueno81@gmail.com>
Tested-by: Pablo Cisneros <patchkez@protonmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c3dfc7c6b0f551fdca3f7c1f1e4c73be8adb17d ]
When a character array without a terminating NUL character has a static
initializer, GCC 15's -Wunterminated-string-initialization will only
warn if the array lacks the "nonstring" attribute[1]. Mark the arrays
with __nonstring to and correctly identify the char array as "not a C
string" and thereby eliminate the warning.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=117178 [1]
Cc: Juergen Gross <jgross@suse.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Cc: xen-devel@lists.xenproject.org
Signed-off-by: Kees Cook <kees@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com>
Message-ID: <20250310222234.work.473-kees@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcca27bc1eccb9abc2552aab950b18a9742fb8e7 ]
Currently armpmu_add() tries to handle a newly-allocated counter having
a stale associated event, but this should not be possible, and if this
were to happen the current mitigation is insufficient and potentially
expensive. It would be better to warn if we encounter the impossible
case.
Calls to pmu::add() and pmu::del() are serialized by the core perf code,
and armpmu_del() clears the relevant slot in pmu_hw_events::events[]
before clearing the bit in pmu_hw_events::used_mask such that the
counter can be reallocated. Thus when armpmu_add() allocates a counter
index from pmu_hw_events::used_mask, it should not be possible to observe
a stale even in pmu_hw_events::events[] unless either
pmu_hw_events::used_mask or pmu_hw_events::events[] have been corrupted.
If this were to happen, we'd end up with two events with the same
event->hw.idx, which would clash with each other during reprogramming,
deletion, etc, and produce bogus results. Add a WARN_ON_ONCE() for this
case so that we can detect if this ever occurs in practice.
That possiblity aside, there's no need to call arm_pmu::disable(event)
for the new event. The PMU reset code initialises the counter in a
disabled state, and armpmu_del() will disable the counter before it can
be reused. Remove the redundant disable.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Tested-by: James Clark <james.clark@linaro.org>
Link: https://lore.kernel.org/r/20250218-arm-brbe-v19-v20-2-4e9922fc2e8e@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4248ee16f411ac1ea7dfab228a6659b111e3d65 ]
When running in a virtual machine, we might see the original hardware CPU
vendor string (i.e. "AuthenticAMD"), but a model and family ID set by the
hypervisor. In case we run on AMD hardware and the hypervisor sets a model
ID < 0x14, the LAHF cpu feature is eliminated from the the list of CPU
capabilities present to circumvent a bug with some BIOSes in conjunction with
AMD K8 processors.
Parsing the flags list from /proc/cpuinfo seems to be happening mostly in
bash scripts and prebuilt Docker containers, as it does not need to have
additionals tools present – even though more reliable ways like using "kcpuid",
which calls the CPUID instruction instead of parsing a list, should be preferred.
Scripts, that use /proc/cpuinfo to determine if the current CPU is
"compliant" with defined microarchitecture levels like x86-64-v2 will falsely
claim the CPU is incapable of modern CPU instructions when "lahf_lm" is missing
in that flags list.
This can prevent some docker containers from starting or build scripts to create
unoptimized binaries.
Admittably, this is more a small inconvenience than a severe bug in the kernel
and the shoddy scripts that rely on parsing /proc/cpuinfo
should be fixed instead.
This patch adds an additional check to see if we're running inside a
virtual machine (X86_FEATURE_HYPERVISOR is present), which, to my
understanding, can't be present on a real K8 processor as it was introduced
only with the later/other Athlon64 models.
Example output with the "lahf_lm" flag missing in the flags list
(should be shown between "hypervisor" and "abm"):
$ cat /proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 15
model : 6
model name : Common KVM processor
stepping : 1
microcode : 0x1000065
cpu MHz : 2599.998
cache size : 512 KB
physical id : 0
siblings : 1
core id : 0
cpu cores : 1
apicid : 0
initial apicid : 0
fpu : yes
fpu_exception : yes
cpuid level : 13
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca
cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx rdtscp
lm rep_good nopl cpuid extd_apicid tsc_known_freq pni
pclmulqdq ssse3 fma cx16 sse4_1 sse4_2 x2apic movbe popcnt
tsc_deadline_timer aes xsave avx f16c hypervisor abm
3dnowprefetch vmmcall bmi1 avx2 bmi2 xsaveopt
... while kcpuid shows the feature to be present in the CPU:
# kcpuid -d | grep lahf
lahf_lm - LAHF/SAHF available in 64-bit mode
[ mingo: Updated the comment a bit, incorporated Boris's review feedback. ]
Signed-off-by: Max Grobecker <max@grobecker.info>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: Borislav Petkov <bp@alien8.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 208baa3ec9043a664d9acfb8174b332e6b17fb69 ]
If malloc returns NULL due to low memory, 'config' pointer can be NULL.
Add a check to prevent NULL dereference.
Link: https://lore.kernel.org/r/20250219122715.3892223-1-quic_zhonhan@quicinc.com
Signed-off-by: Zhongqiu Han <quic_zhonhan@quicinc.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
