Redundant entries for wifi nodes, reserved-memory and pcie0_rp are
defined in sdxlemur-qcn9000.dtsi.
Remove the redundant entries as they are not required.
Change-Id: Idb3e4f1a34d220076b5c797616d96d9bfa82f6c5
PMIC PM8008 LDOs do not support low power mode (LPM). If configured for
LPM, these LDOs continue to operate in normal power mode (NPM) with the
same quiescent current but a reduced over-current protection (OCP)
threshold, which can result in OCP triggering. Fix all PM8008 LDOs
to use normal power mode (NPM) alone to avoid this.
Change-Id: I2c8961eaba0677768da09aeba577a32810c1d50f
Add a nvmem cell for adc scaling within PMK8350 SDAM127 for yupik.
This is used by clients to read the type of ADC scaling used for ibat.
Change-Id: I1978fcf5ca18dd878da20bdacaf7d8d3c643d199
Remove support for PCIE1, USB3_SEC clocks and GDSC's as they are
not required for YUPIK HSP attach.
Change-Id: I1c4bfe0e5e7191bad8cd678bb14417b5ffae426e
Add support to scale ibat current for greater than default max
supported ranges using range factor provided from nvmem.
Change-Id: I63cc53cdba021300839695e9378fc320d57b2840
Defines the restore-after-cx-collapse property for SDCC controller.
This basically lets the driver know that software needs to save the SDCC
register contents before the CX/XO event and restore the SDCC
register contents after coming out of CX/XO event.
SDCC controller is not supporting retention of CX PC hence this change is
needed.
Change-Id: I719e7de2143edc457e706a66279bde816296ec73
Remove the qcom,power-always-on dt property for the holi, shima, yupik
and lahaina targets as its support is removed from driver.
Change-Id: Ia35844b02bb2e4da7d36ef7b7f260c34da4fc861
This is a snapshot of the sdx ipc driverdriver as of msm-4.14
commit a5650700 ("drivers: qcom: sdx_ext_ipc: keep wakeup irq
always on").
Change-Id: I27eb35b33284be8c221cd873323a488101a2f5e8
Enable pin control for qps615 that is necessary to configure
the SDX65 GPIO pins for Wake on LAN support.
Change-Id: Ic5d6d76677e195fc3dec7780d99b5cf50718b8b1
Rename snps,usb2_l1_disable to snps,usb2-gadget-lpm-disable
since driver code for disabling L1 was changed and renamed
to snps,usb2-gadget-lpm-disable in order to align with
upstream.
Change-Id: Ic95baa810ac4da004e83e8a2b25bbfbcd74350df
Add the following changes to support QCN9000 in MTP CPE 1x Pine platform:
1. Add sdxlemur-qcn9000.dtsi to have all QCN9000 related configs.
2. Add memory reservation of 2x52 MB for 2 QCN9000 in
sdxlemur-qcn9000.dtsi but in disabled state.
3. Enable reserved memory for 1 QCN9000 in sdxlemur-mtp-cpe-pine1x.dtsi.
4. Add wifi node with all QCN9000 related configs.
5. Enable pcie0_bus2_dev1_fn0 node with QCN9000 memory configs.
6. Enable GPIO 102 to power on QCN9000.
Change-Id: Ieaa7e6fb567581f6d82ae6edfc2f664adf3ef4cc
sdxlemur-mtp-cpe.dtsi is included in sdxlemur-mtp-cpe.dts as well as
sdxlemur-mtp-cpe-pine1x.dts. WLAN configs present in
sdxlemur-mtp-cpe.dtsi is not applicable for sdxlemur-mtp-cpe-pine1x.dts.
Move all WLAN specific configurations from sdxlemur-mtp-cpe.dtsi to a
new file sdxlemur-mtp-cpe-hsp.dtsi and include this file in
sdxlemur-mtp-cpe.dts only.
Change-Id: I245662cf6b23dcb3b5c5fc5ce2ac61783b801cdc
