With multicodec approach, codec widgets are added much earlier during sound
card registration than aux codec approach. The connections between bolero and wcd938x
are done via device tree at a later point. DAPM does power checkup for codec widgets
before the codec-codec path is connected. This results in wcd938x dapm inputs/output
to be considered as endpoints, which results in playback/record failure once after
bootup. Hence, add dummy output/input widgets to wcd938x dapm inputs/output which are not
codec endpoints.
Change-Id: I5ab4839e9b76adba24c9254ae56dc784b4448af7
Signed-off-by: Vignesh Kulothungan <vigneshk@codeaurora.org>
In case of two concurrent active rx proxy ports, add
separate callback data to handle proxy reading.
Change-Id: I4de631b9cfead777c970103a79578964e5950eb9
Signed-off-by: Zhou Song <zhous@codeaurora.org>
Restore change to retain audio_hm voting and
ensure AOP hang issue not seen by masking interrupt
wakeup of swr pinctrl pins.
Change-Id: I51bf36d6d6b0999abf10a4bc94cce900d1adf1d5
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
For island SVA usecase, ensure register for
AFE in-band interrupt.
Change-Id: I24e6dfadfaa38919114000fb09a7906264020cd9
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Only send codec dma data alignment cmd when it's set.
Change-Id: I413c28bc01b4f49aa0291b868852dfb5835add8e
Signed-off-by: Meng Wang <mengw@codeaurora.org>
Config variables are no longer supported and are replaced by
audio effects config in Lahaina.
Change-Id: Ic817791a470a7e4b0fac280115edf849fecc91c7
Signed-off-by: Akhil Karuturi <akarutur@codeaurora.org>
In register show function, when snprintf returns a negative value
out of bounds access occurs while copying the data to user.
Add return value check on snprintf before copy_to_user
to fix this and add sizeof() for tmp_buff to avoid buffer
overflow.
Change-Id: I15f1add37987d2176a165669d7a5b40bd576004c
Signed-off-by: Prasad Kumpatla <nkumpat@codeaurora.org>
Add changes for VI sense WSA_CDC_DMA_TX_0 as backend
dailink to support recording of VI sense data.
Change-Id: Iea90290f2189d669ca5660373849a7e987483fc4
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Add ignore suspend for dapm widgets to avoid waking up the
system during power collapse.
Change-Id: I4eec9785f2e722d1fbcbf26c2635af9825b30115
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Add dapm ignore suspend for playback and capture DAIs to
avoid wakeup during power collapse.
Change-Id: If023597542423253a565dcf0f13ee9f08b357b93
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Update interrupt handling on WSA883x driver to avoid fake
interrupts during power collapse.
Change-Id: I3128e2c2d9bf84f90f472a03d2b23ca1d3b70838
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Disable wsa swr gpio as wakeup capable to avoid waking up system
during power collapse.
Change-Id: I54d769d63c9e7c13d2920f038c64353a92556cfe
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Add delay in post ssr to eliminate playback pause on euro usbc headset.
Post ssr, headset is detected as headphone as HPH PA gets turned ON
before the completion of wcd_correct_swch_plug workqueue in MBHC.
Change-Id: Ib0334b37aa12b7e7371146b26eb3a1f4484656a3
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
Move volume and app type cfg controls from asoc to
audio drivers.
Change-Id: I5c5d84a9a0536c7d8d95a8ca20cc176b31ca5b63
Signed-off-by: Meng Wang <mengw@codeaurora.org>
HPH PA pull down control is set to force ON instead of auto
due of which saturation/noise is observed in headset
playback at highest volumes. Set pull down control
to Auto to fix this issue.
Change-Id: I465588f46b04bbb32d84f76b8b5bedd2ef21bd2a
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
When current source mode is enabled, comparator auto
zeroing should be turned ON by HW. As rouleur codec HW
doesn't do this automatically, add this support
in SW to set the auto zero enable before FSM enable
and reset to auto once FSM is enabled.
Disable surge protection before ADC measurements
and change HPHL and HPHR thresholds while
identifying cross connection for proper
accessory identification.
Change-Id: Ib775de0f0bdb6c655a3c0eb4775276acfbca1e84
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
