Add check to verify if valid error code is returned from mini
dump add region.
Change-Id: I02e2cfef22ce5f812104d7dc05dbb623c5c1670f
Signed-off-by: vgattupa <vgattupa@codeaurora.org>
Enable QoS configuration for GIC master port to set the default
priority to P2.
Change-Id: I16fca1e47be19bfe395ec71fc32ac66a664f9b4e
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Add endpoint ID for GIC master which consumers can use to set bandwidth
constraints and find paths in the NoC (Network-On-Chip) topology.
Change-Id: I673888840c4dc2770ccb6d5dab76bab72c3af3cf
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
These virtio clocks are necessary for USB2 pass-through on
sa8195p virtual machine.
Change-Id: Ieef15c9ee8652ff2b182cc08f5d6ac7b3738c1a1
Signed-off-by: Yimin Peng <yiminp@codeaurora.org>
Support read opp value for dev_target.
Use previous_freq instead of get_cur_freq when opp
table parsed success.
Change-Id: I37bb74ef18a822b05ed3be411bc59ae4dadb7a0d
Signed-off-by: Biao Long <blong@codeaurora.org>
Add packet count stats for rx and tx for each queue in ethtool.
Change-Id: I5f2c2f68fb87c9cb8436f2c589b0884404e47233
Signed-off-by: Suraj Jaiswal <jsuraj@codeaurora.org>
Add support for camera and video clks for clock clients to be able
to request for the clocks in MONACO. Also update the gpucc_pll0_out_odd
source to gpucc_pll0_out_even src for gfx clk src for MONACO.
Change-Id: I3b4efffb828e38f684051b7265e5481b0bce14e5
Signed-off-by: Saurabh Sahu <sausah@codeaurora.org>
Read early ethernet dtsi flag to enable this feature.
Disable autoneg and configure MAC and PHY with 100 Mbps
link speed.
Read MAC addr, IPv4 and IPv6 addresses from kernel cmd
line parameters in order to assign these to ethernet
interface.
Change-Id: Ibeeebb73b4cbbd0950a1bff065297c4e58be671d
Acked-by: Nagarjuna Chaganti <nchagant@qti.qualcomm.com>
Signed-off-by: Suraj Jaiswal <jsuraj@codeaurora.org>
WLAN MAC address can be provisioned using NV memory based setup.
DMS QMI server connection is required to retrieve this MAC address.
Thus setup DMS QMI client in icnss platform driver and send this
MAC address for WLAN FW before mission mode enable.
1. Move DMS QMI files to cnss_util from cnss2.
2. Read "use-nv-mac" property from DT node to decide whether
reding MAC address from NV memory is mandatory or not.
If mandatory wait for DMS QMI server to read MAC address.
If not mandatory read MAC address if DMS server is available
otherwise continue.
Change-Id: Iddc5a7180c9eea2a8a9507f08b1b383bc095f2bc
Signed-off-by: Naman Padhiar <npadhiar@codeaurora.org>
The vdd mappings do not seem to be correct as per sdxnightjar, thus
update the vdd file and also remove the vdd proxy voting by adding the
sync state call back.
Change-Id: Iac53f0762d1e3ed62774e3e3305a45bdfc83df24
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Define a vdd_levels enum and vdd_corner[] mapping table which
can be used by clock controller drivers to configure the
vdd_class associated with their clocks.
Change-Id: Ic32aa8ed63bc756cdc10e8d5a5591011a84c4ede
Signed-off-by: Taniya Das <tdas@codeaurora.org>
From the kernel 5.1, added a "dm-mod.create" kernle cmdline parameter,
which allows device-mapper targets to be configured at boot time.
This enables early use of DM targets in the boot process (as the root
device or otherwise) without the need of an initramfs. So enabled the
dm-init module for dm-verity.
Change-Id: Ice0c62d00f49f8c038fd315c8baf076fa83c5daf
Signed-off-by: Nan Zhang <nanzhan@codeaurora.org>
Add support for the following LCDB devicee tree properties:
"qcom,high-p2-blank-time-ns" to control the higher clamp threshold for
p2 minimum on time.
"qcom,low-p2-blank-time-ns" to control the lower clamp threshold for
p2 minimum on time.
"qcom,mpc-current-thr-ma" to control the mpc threshold for inductor
current after start up is done.
Change-Id: Iabe2cc2c9913f433dd55d952a267f94ce0682f0e
Signed-off-by: Jishnu Prakash <jprakash@codeaurora.org>
Enable CONFIG_CAN and CONFIG_QTI_CAN for CAN devices
on autogen3 platform.
Change-Id: Id0602fa32e6f5c2a1c206c8f0252dc36f1204f5a
Signed-off-by: Zou Shunxiang <shunxian@codeaurora.org>
The haptics module would get stuck in SWR mode if SWR port is
disconnected during SWR play, and this can happen if ADSP SSR
(subsystem reset) is triggered when playing in SWR mode. This
stuck condition can be detected by checking if haptics module
has already been in SWR mode when swr-haptics driver requests
to enable SWR haptics. When it's detected, ignore SWR mode
temporarily and toggle HAPTICS_EN for a HW reset. When SWR play
is attempted again i.e. when swr_haptics driver request to turn
on SWR slave device, SWR mode would get re-enabled.
Change-Id: Ie55d331e3c689972b42dd9688f0d2b182b3fd282
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
