Enable RENAME_BLOCK_DEVICE in quinvm to support renaming of
partitions for AVB 2.0 support.
Change-Id: Ia283eb8217ea019dd66680480487cfefdffcfb02
Signed-off-by: Venkata Rao Kakani <vkakani@codeaurora.org>
BY default MPM_WAKEUP_INT_EN bits are set from firmware
for gpios which can have wakeup capability. This results
in wakeup capability set for a gpio which is not being used
as IRQ. Problem manifests as spurious interrupts coming to
GIC from PDC as MPM_WAKEUP_INT_EN registers bit corresponding
to gpio is set.
Fix this by disabling wakeup capability for gpio not being
used as IRQ. When client driver calls irq_set_irq_wake()
after requesting gpio as irq, enable wakeup capability.
Change-Id: Ie215f2fdd36483b133b17ec8162c7423a7d8db31
Signed-off-by: Prateek Sood <prsood@codeaurora.org>
Add fastcvp driver, which exposes APIs to video driver
to share HFI command queue address to CDSP and
handle errors to exit gracefully in case video and
cdsp subsystems restart.
This snapshot was taken as of msm-4.14 with commit
5704525974fc1f3cb3f14d922d4987f35f2dc278.
Change-Id: I2b75e01f88d4bc5a267942e63cab79094ef327b9
Signed-off-by: Laisheng Hu <laisheng@codeaurora.org>
Add support for global clock controller for peripheral
clock clients to be able to request for the clocks in
Monaco.
Change-Id: I0dcf82faf9073a7ee832c693540dddbca44e2524
Signed-off-by: Saurabh Sahu <sausah@codeaurora.org>
Currently the driver enables autoresume for all the connected
peripherals. In a case where an LS device is connected but fails
the enumeration, this autoresume enablement is leading to PHY
keeping the Dm pulled up even when the peripheral is detached.
Hence, the detach hs_phy_irq is never fired and disconnect is
not processed.
Since remote wakeup from LS peripherals is not a requirement on
our platforms, enable autoresume for FS/HS devices only.
Change-Id: I0a62d08e58af18b523af322c64529f5183d55907
Signed-off-by: Ajay Agarwal <ajaya@codeaurora.org>
Currently the driver checks whether the PED bit of the PORTSC
register is set to decide whether any device is connected, and
then checks the PORTSPEED field to check for the speed and
accordingly updates the HSPHY speed flag with LS or FS/HS. Hence,
the PDC is programmed to fire HS_PHY_IRQ only on the rising edge
of Dp/Dm.
In a case where the connected peripheral has failed to enumerate,
the PED bit can be cleared by the host driver. When such a device
is disconnected, there is no HS_PHY_IRQ fired to wakeup SW and
disconnect handling does not happen.
Fix this by setting HSPHY speed flags based on the CCS bit of the
PORTSC register so that the PDC is programmed to fire HS_PHY_IRQ
on the falling edge of Dp/Dm.
Change-Id: I122d170434da19fd6aeb022a5fa8a85f1ea6f541
Signed-off-by: Ajay Agarwal <ajaya@codeaurora.org>
Enable MFD SPMI PMIC driver and several SPMI and PMIC drivers
which are needed to provide baseline support of PMIC peripherals.
Change-Id: I965b40eb0931c2e22e9fab28626e9ca753ad3ff8
Signed-off-by: Veera Vegivada <vvegivad@codeaurora.org>
Add support for mpm wakeup control capability, for selective
enable of wakeup capability for GPIO being used as IRQ.
Change-Id: I38f5c8eea4b12919fb95b2135d76579eb4b27247
Signed-off-by: Prateek Sood <prsood@codeaurora.org>
