Creating logical mappings for the secure CDSP heap memory may
cause problems with respect to speculative access, so ensure
that no logical kernel mappings are created for that region.
Change-Id: I56c23e82c1a4ba52322aa0f5a2045e482a8586ff
As the emulation platform is very slow, we may encounter watchdog
barks/bites very often. Hence, explicitly disable the device-tree
node for the watchdog driver for this platform.
Change-Id: I11e48439370efdd27c2c6cee6798fe0d22e2bd7d
Update the arch_timer frequency to 19.2 MHz, now that the device
boots up on a real hardware (instead of an emulation platform).
Leave the 96KHz still intact for emulation platforms.
Change-Id: I3745395b88d8aa9d1b0047b4eca7c85db4ec7a13
When lahaina-rumi is compiled as a separate overlay, it does
not explicitly include the definition of the &soc node. Without
the #address-cells and #size-cells specifiers, the compiler uses
default values of 2 and 1, respectively, which results in the
following warnings when compiling lahaina-rumi-overlay.dtb:
Warning (reg_format): "reg" property in
/fragment@15/__overlay__/usb_emu_phy@a720000 has invalid length (8
bytes) (#address-cells == 2, #size-cells == 1) Warning
(avoid_default_addr_size): Relying on default #address-cells value for
/fragment@15/__overlay__/usb_emu_phy@a720000
Warning (avoid_default_addr_size): Relying on default #size-cells
value for /fragment@15/__overlay__/usb_emu_phy@a720000
As the &soc node is referenced here only for the purpose of adding
a new child node, usb_emu_phy, address the warnings by explicitly
defining the {address,size}-cells values.
Change-Id: I8b5ebcd53c060eeea3c55bf9fb8e55093e7862f2
Qualcomm Technologies, Inc. (QTI) High Voltage (HV) PMIC haptics
modules can support up to 10 V voltage to drive either ERM or LRA.
It has an integrated module to support auto resonance detection
and correction for LRA actuator. It can play different vibration
effects with different pattern sources. It also has an integrated
brake module which can work in different modes to use BEMF for
quick vibration stop.
Change-Id: Id8b9fa1e4eefc7dda325e25728e59af9c1de9049
Add a register value mask which will specify which bits of the register
will be updated with the value. For instance, if mask is 0x11, then
only bit 0 & bit 4 will be updated with the corresponding bits of the
specified value.
Change-Id: I27471c3afee72ac99f955030ab2100f3685d46d9
Document usage of interconnects and interconnect-names properties
for the USB controller node. This replaces the now obsolete msm_bus
bindings.
Change-Id: I4a1a2cd6a115584986bba28ba121d3fbea7cb409
QTI battery glink debug device helps to get logs and debug
information by communicating with charger firmware running on the
remote subsystem (e.g. DSP) over PMIC Glink.
Change-Id: I3a894b40bbbb67dbe26ad683cfabe330bf7e3d69
Add proxy-consumer properties to the VDD_MMCX rpmh-regulator
device node so that VDD_MMCX is kept enabled starting from
early in the application processor's boot sequence. This
avoids issues when accessing multimedia clock controller
registers at initialization time.
Additionally, add proxy-consumer properties to the VDD_CX and
VDD_MX device nodes to avoid potential issues caused by a
clock voting for a lower voltage level than what is physically
required by a clock that is initialized at a later point.
Change-Id: I4de02193c6d1e29664e9cb3198b56dca9956ccce
Update the min and max voltage limits for Lahaina RPMh regulator
devices so that they match the limits imposed by boot loaders.
Update initial voltages where necessary to bring them into the
new min/max ranges.
Also, add support for PM8350B LDO 1 and remove support for PM8350
LDO 10 to match the resources being exposed by RPMh. Lastly,
move VDD_EBI level control support from PM8350C SMPS 3 to SMPS 2
to match the finalized power grid.
Change-Id: Ie816a5ba2ae11b8c60377e5bb3620dbafb6085a1
Lahaina CDP overlay device tree source file that was missed in commit
<89d5927337> ("ARM: dts: msm: Add device tree overlay support for
Lahaina").
Change-Id: Ie9347f106e488384f4ddb6976d955e3b05433963
Added a new property "qcom,fastrpc-gids" to the fastrpc node on
Lahaina, which will contain the list of privileged group IDs. This
feature is for resource management on remote subsystem.
Change-Id: I67940202cf4d199b0f2bc0be0eebc7c19581c0a2
Acked-by: Thyagarajan Venkatanarayanan <venkatan@qti.qualcomm.com>
