commit 8744dcd4fc7800de2eb9369410470bb2930d4c14 upstream.
In case the stm32_lptim_set_enable_state() fails to update CMP and ARR,
a timeout error is raised, by regmap_read_poll_timeout. It may happen,
when the lptimer runs on a slow clock, and the clock is gated only
few times during the polling.
Badly, when this happen, STM32_LPTIM_ENABLE in CR register has been set.
So the 'enable' state in sysfs wrongly lies on the counter being
correctly enabled, due to CR is read as one in stm32_lptim_is_enabled().
To fix both issues:
- enable the clock before writing CMP, ARR and polling ISR bits. It will
avoid the possible timeout error.
- clear the ENABLE bit in CR and disable the clock in the error path.
Fixes: d8958824cf ("iio: counter: Add support for STM32 LPTimer")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20250224170657.3368236-1-fabrice.gasnier@foss.st.com
Signed-off-by: William Breathitt Gray <wbg@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 932b32ffd7604fb00b5c57e239a3cc4d901ccf6e upstream.
nf_sk_lookup_slow_v4 does the conntrack lookup for IPv4 packets to
restore the original 5-tuple in case of SNAT, to be able to find the
right socket (if any). Then socket_match() can correctly check whether
the socket was transparent.
However, the IPv6 counterpart (nf_sk_lookup_slow_v6) lacks this
conntrack lookup, making xt_socket fail to match on the socket when the
packet was SNATed. Add the same logic to nf_sk_lookup_slow_v6.
IPv6 SNAT is used in Kubernetes clusters for pod-to-world packets, as
pods' addresses are in the fd00::/8 ULA subnet and need to be replaced
with the node's external address. Cilium leverages Envoy to enforce L7
policies, and Envoy uses transparent sockets. Cilium inserts an iptables
prerouting rule that matches on `-m socket --transparent` and redirects
the packets to localhost, but it fails to match SNATed IPv6 packets due
to that missing conntrack lookup.
Closes: https://github.com/cilium/cilium/issues/37932
Fixes: eb31628e37 ("netfilter: nf_tables: Add support for IPv6 NAT")
Signed-off-by: Maxim Mikityanskiy <maxim@isovalent.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ccea4784fddd96fbd6c4497eb28b45dab638c2a upstream.
Commit 169f9102f9198b ("ARM: 9350/1: fault: Implement
copy_from_kernel_nofault_allowed()") added the function to check address
before use. However, for devices without MMU, addr > TASK_SIZE will
always fail. This patch move this function after the #ifdef CONFIG_MMU
statement.
Signed-off-by: Yanjun Yang <yangyj.ee@gmail.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218953
Fixes: 169f9102f9198b ("ARM: 9350/1: fault: Implement copy_from_kernel_nofault_allowed()")
Link: https://lore.kernel.org/r/20240611100947.32241-1-yangyj.ee@gmail.com
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f09b8b4fa58e99cbfd9a650b31d65cdbd8e4276 upstream.
The common pattern in arm is to emit a "8<--- cut here ---" line for
faults, but it was missing for do_PrefetchAbort(). Add it.
Cc: Wang Kefeng <wangkefeng.wang@huawei.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 169f9102f9198b04afffa6164372a4ba4070f412 upstream.
Under PAN emulation when dumping backtraces from things like the
LKDTM EXEC_USERSPACE test[1], a double fault (which would hang a CPU)
would happen because of dump_instr() attempting to read a userspace
address. Make sure copy_from_kernel_nofault() does not attempt this
any more.
Closes: https://lava.sirena.org.uk/scheduler/job/497571
Link: https://lore.kernel.org/all/202401181125.D48DCB4C@keescook/ [1]
Reported-by: Mark Brown <broonie@kernel.org>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Cc: Wang Kefeng <wangkefeng.wang@huawei.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9821709af892be9fbf4ee9a50b2f3e0604295ce0 upstream.
Add mapping for headset mute key events.
Remove PLT_QUIRK_DOUBLE_VOLUME_KEYS quirk and made it generic.
The quirk logic did not keep track of the actual previous key
so any key event occurring in less than or equal to 5ms was ignored.
Remove PLT_QUIRK_FOLLOWED_OPPOSITE_VOLUME_KEYS quirk.
It had the same logic issue as the double key quirk and was actually
masking the as designed behavior of most of the headsets.
It's occurrence should be minimized with the ALSA control naming
quirk that is part of the patch set.
Signed-off-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 486f6205c233da1baa309bde5f634eb1f8319a33 upstream.
Many Poly/Plantronics headset families name the feature, input,
and/or output units in a such a way to produce control names
that are not recognized by user space. As such, the volume and
mute events do not get routed to the headset's audio controls.
As an example from a product family:
The microphone mute control is named
Headset Microphone Capture Switch
and the headset volume control is named
Headset Earphone Playback Volume
The quirk fixes these to become
Headset Capture Switch
Headset Playback Volume
Signed-off-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd8689b52a24807c2d5ce0a17cb26dc87f75235c upstream.
On the off chance that command stream passed from userspace via
ioctl() call to radeon_vce_cs_parse() is weirdly crafted and
first command to execute is to encode (case 0x03000001), the function
in question will attempt to call radeon_vce_cs_reloc() with size
argument that has not been properly initialized. Specifically, 'size'
will point to 'tmp' variable before the latter had a chance to be
assigned any value.
Play it safe and init 'tmp' with 0, thus ensuring that
radeon_vce_cs_reloc() will catch an early error in cases like these.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 2fc5703abd ("drm/radeon: check VCE relocation buffer range v3")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2d52de55f9ee7aaee0e09ac443f77855989c6b68)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 548b0c5de7619ef53bbde5590700693f2f6d2a56 upstream.
An OGMv1 and OGMv2 packet receive processing were not only limited by the
number of bytes in the received packet but also by the nodes maximum
aggregation packet size limit. But this limit is relevant for TX and not
for RX. It must not be enforced by batadv_(i)v_ogm_aggr_packet to avoid
loss of information in case of a different limit for sender and receiver.
This has a minor side effect for B.A.T.M.A.N. IV because the
batadv_iv_ogm_aggr_packet is also used for the preprocessing for the TX.
But since the aggregation code itself will not allow more than
BATADV_MAX_AGGREGATION_BYTES bytes, this check was never triggering (in
this context) prior of removing it.
Cc: stable@vger.kernel.org
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Fixes: 9323158ef9 ("batman-adv: OGMv2 - implement originators logic")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 379c590113ce46f605439d4887996c60ab8820cc upstream.
When the addresses of the shmobile_smp_mpidr, shmobile_smp_fn, and
shmobile_smp_arg variables are not multiples of 4 bytes, secondary CPU
bring-up fails:
smp: Bringing up secondary CPUs ...
CPU1: failed to come online
CPU2: failed to come online
CPU3: failed to come online
smp: Brought up 1 node, 1 CPU
Fix this by adding the missing alignment directive.
Fixes: 4e960f52fc ("ARM: shmobile: Move shmobile_smp_{mpidr, fn, arg}[] from .text to .bss")
Closes: https://lore.kernel.org/r/CAMuHMdU=QR-JLgEHKWpsr6SbaZRc-Hz9r91JfpP8c3n2G-OjqA@mail.gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/c499234d559a0d95ad9472883e46077311051cd8.1741612208.git.geert+renesas@glider.be
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e51a349d2dcf1df8422dabb90b2f691dc7df6f92 upstream.
The error path when atmci_configure_dma() set dma fails in atmci driver
does not correctly disable the clock.
Add the missing clk_disable_unprepare() to the error path for pair with
clk_prepare_enable().
Fixes: 467e081d23 ("mmc: atmel-mci: use probe deferring if dma controller is not ready yet")
Signed-off-by: Gu Bowen <gubowen5@huawei.com>
Acked-by: Aubin Constans <aubin.constans@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250225022856.3452240-1-gubowen5@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80cbee810e4e13cdbd3ae9654e9ecddf17f3e828 upstream.
The V3D driver still relies on `drm_sched_increase_karma()` and
`drm_sched_resubmit_jobs()` for resubmissions when a timeout occurs.
The function `drm_sched_increase_karma()` marks the job as guilty, while
`drm_sched_resubmit_jobs()` sets an error (-ECANCELED) in the DMA fence of
that guilty job.
Because of this, we must check whether the job’s DMA fence has been
flagged with an error before executing the job. Otherwise, the same guilty
job may be resubmitted indefinitely, causing repeated GPU resets.
This patch adds a check for an error on the job's fence to prevent running
a guilty job that was previously flagged when the GPU timed out.
Note that the CPU and CACHE_CLEAN queues do not require this check, as
their jobs are executed synchronously once the DRM scheduler starts them.
Cc: stable@vger.kernel.org
Fixes: d223f98f02 ("drm/v3d: Add support for compute shader dispatch.")
Fixes: 1584f16ca9 ("drm/v3d: Add support for submitting jobs to the TFU.")
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250313-v3d-gpu-reset-fixes-v4-1-c1e780d8e096@igalia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 285df995f90e3d61d97f327d34b9659d92313314 upstream.
On the GTA04A5 writing a reset command to the gyroscope causes IRQ
storms because NACK IRQs are enabled and therefore triggered but not
acked.
Sending a reset command to the gyroscope by
i2cset 1 0x69 0x14 0xb6
with an additional debug print in the ISR (not the thread) itself
causes
[ 363.353515] i2c i2c-1: ioctl, cmd=0x720, arg=0xbe801b00
[ 363.359039] omap_i2c 48072000.i2c: addr: 0x0069, len: 2, flags: 0x0, stop: 1
[ 363.366180] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x1110)
[ 363.371673] omap_i2c 48072000.i2c: IRQ (ISR = 0x0010)
[ 363.376892] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.382263] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.387664] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
repeating till infinity
[...]
(0x2 = NACK, 0x100 = Bus free, which is not enabled)
Apparently no other IRQ bit gets set, so this stalls.
Do not ignore enabled interrupts and make sure they are acked.
If the NACK IRQ is not needed, it should simply not enabled, but
according to the above log, caring about it is necessary unless
the Bus free IRQ is enabled and handled. The assumption that is
will always come with a ARDY IRQ, which was the idea behind
ignoring it, proves wrong.
It is true for simple reads from an unused address.
To still avoid the i2cdetect trouble which is the reason for
commit c770657bd261 ("i2c: omap: Fix standard mode false ACK readings"),
avoid doing much about NACK in omap_i2c_xfer_data() which is used
by both IRQ mode and polling mode, so also the false detection fix
is extended to polling usage and IRQ storms are avoided.
By changing this, the hardirq handler is not needed anymore to filter
stuff.
The mentioned gyro reset now just causes a -ETIMEDOUT instead of
hanging the system.
Fixes: c770657bd261 ("i2c: omap: Fix standard mode false ACK readings").
CC: stable@kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250228140420.379498-1-andreas@kemnade.info
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 90a7138619a0c55e2aefaad27b12ffc2ddbeed78 ]
Previous commit 8b5c171bb3 ("neigh: new unresolved queue limits")
introduces new netlink attribute NDTPA_QUEUE_LENBYTES to represent
approximative value for deprecated QUEUE_LEN. However, it forgot to add
the associated nla_policy in nl_ntbl_parm_policy array. Fix it with one
simple NLA_U32 type policy.
Fixes: 8b5c171bb3 ("neigh: new unresolved queue limits")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Link: https://patch.msgid.link/20250315165113.37600-1-linma@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3009d0d6ab78053117f8857b921a8237f4d17b3 ]
The ->send() operation frees skb so save the length before calling
->send() to avoid a use after free.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/c751531d-4af4-42fe-affe-6104b34b791d@stanley.mountain
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a81fc3480bf5dbe2bf80e278c440770f6ba2692 ]
While creating a new IPv6, we could get a weird -ENOMEM when
RTA_NH_ID is set and either of the conditions below is true:
1) CONFIG_IPV6_SUBTREES is enabled and rtm_src_len is specified
2) nexthop_get() fails
e.g.)
# strace ip -6 route add fe80::dead:beef:dead:beef nhid 1 from ::
recvmsg(3, {msg_iov=[{iov_base=[...[
{error=-ENOMEM, msg=[... [...]]},
[{nla_len=49, nla_type=NLMSGERR_ATTR_MSG}, "Nexthops can not be used with so"...]
]], iov_len=32768}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 148
Let's set err explicitly after ip_fib_metrics_init() in
ip6_route_info_create().
Fixes: f88d8ea67f ("ipv6: Plumb support for nexthop object in a fib6_info")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20250312013854.61125-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9740890ee20e01f99ff1dde84c63dcf089fabb98 ]
fib_check_nh_v6_gw() expects that fib6_nh_init() cleans up everything
when it fails.
Commit 7dd73168e2 ("ipv6: Always allocate pcpu memory in a fib6_nh")
moved fib_nh_common_init() before alloc_percpu_gfp() within fib6_nh_init()
but forgot to add cleanup for fib6_nh->nh_common.nhc_pcpu_rth_output in
case it fails to allocate fib6_nh->rt6i_pcpu, resulting in memleak.
Let's call fib_nh_common_release() and clear nhc_pcpu_rth_output in the
error path.
Note that we can remove the fib6_nh_release() call in nh_create_ipv6()
later in net-next.git.
Fixes: 7dd73168e2 ("ipv6: Always allocate pcpu memory in a fib6_nh")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250312010333.56001-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72d061ee630d0dbb45c2920d8d19b3861c413e54 ]
The chan_alloc_skb_cb() function is supposed to return error pointers on
error. Returning NULL will lead to a NULL dereference.
Fixes: 6b8d4a6a03 ("Bluetooth: 6LoWPAN: Use connected oriented channel instead of fixed one")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b5e41a8b51fce520bb09bd651a29ef495e990de ]
There is no difference between the sge of READ and non-READ
operations in hns RoCE. Set max_sge_rd to the same value as
max_send_sge.
Fixes: 9a4435375c ("IB/hns: Add driver files for hns RoCE driver")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20250311084857.3803665-8-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81c0db302a674f8004ed805393d17fd76f552e83 ]
Driver is always clearing the mask that sets the VLAN ID/Service Level
in the adapter. Recent change for supporting multiple traffic class
exposed this issue.
Allow setting SL and VLAN_ID while QP is moved from INIT to RTR state.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Fixes: c64b16a37b6d ("RDMA/bnxt_re: Support different traffic class")
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1741670196-2919-1-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0aae2867aa6067f73d066bc98385e23c8454a1d7 ]
The cited commit fixed a software GSO bug with VXLAN + IPSec in tunnel
mode. Unfortunately, it is slightly broader than necessary, as it also
severely affects performance for Geneve + IPSec transport mode over a
device capable of both HW GSO and IPSec crypto offload. In this case,
xfrm_output unnecessarily triggers software GSO instead of letting the
HW do it. In simple iperf3 tests over Geneve + IPSec transport mode over
a back-2-back pair of NICs with MTU 1500, the performance was observed
to be up to 6x worse when doing software GSO compared to leaving it to
the hardware.
This commit makes xfrm_output only trigger software GSO in crypto
offload cases for already encapsulated packets in tunnel mode, as not
doing so would then cause the inner tunnel skb->inner_networking_header
to be overwritten and break software GSO for that packet later if the
device turns out to not be capable of HW GSO.
Taking a closer look at the conditions for the original bug, to better
understand the reasons for this change:
- vxlan_build_skb -> iptunnel_handle_offloads sets inner_protocol and
inner network header.
- then, udp_tunnel_xmit_skb -> ip_tunnel_xmit adds outer transport and
network headers.
- later in the xmit path, xfrm_output -> xfrm_outer_mode_output ->
xfrm4_prepare_output -> xfrm4_tunnel_encap_add overwrites the inner
network header with the one set in ip_tunnel_xmit before adding the
second outer header.
- __dev_queue_xmit -> validate_xmit_skb checks whether GSO segmentation
needs to happen based on dev features. In the original bug, the hw
couldn't segment the packets, so skb_gso_segment was invoked.
- deep in the .gso_segment callback machinery, __skb_udp_tunnel_segment
tries to use the wrong inner network header, expecting the one set in
iptunnel_handle_offloads but getting the one set by xfrm instead.
- a bit later, ipv6_gso_segment accesses the wrong memory based on that
wrong inner network header.
With the new change, the original bug (or similar ones) cannot happen
again, as xfrm will now trigger software GSO before applying a tunnel.
This concern doesn't exist in packet offload mode, when the HW adds
encapsulation headers. For the non-offloaded packets (crypto in SW),
software GSO is still done unconditionally in the else branch.
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Yael Chemla <ychemla@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Fixes: a204aef9fd77 ("xfrm: call xfrm_output_gso when inner_protocol is set in xfrm_output")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbf10b86f6057cf79300720da4ea4b77e6708b0d ]
imx_scu_probe() calls of_parse_phandle_with_args(), but does not
release the OF node reference obtained by it. Add a of_node_put() call
after done with the node.
Fixes: f25a066d1a07 ("firmware: imx-scu: Support one TX and one RX")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b22459792fcb4def9f0936d64575ac11a95a58d ]
If i2c_add_adapter() fails, the request_region() call in sis630_setup()
must be undone by a corresponding release_region() call, as done in the
remove function.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/3d607601f2c38e896b10207963c6ab499ca5c307.1741033587.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e55caaf30c88209d097e575a169b1dface1ab69 ]
If i2c_add_adapter() fails, the request_region() call in ali15x3_setup()
must be undone by a corresponding release_region() call, as done in the
remove function.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/9b2090cbcc02659f425188ea05f2e02745c4e67b.1741031878.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b5463f349d019a261f1e80803447efca3126151 ]
If i2c_add_adapter() fails, the request_region() call in ali1535_setup()
must be undone by a corresponding release_region() call, as done in the
remove function.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/0daf63d7a2ce74c02e2664ba805bbfadab7d25e5.1741031571.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed92bc5264c4357d4fca292c769ea9967cd3d3b6 ]
Free some resources in the error handling path of the probe, as already
done in the remove function.
Fixes: e3523e0186 ("ASoC: wm0010: Add initial wm0010 DSP driver")
Fixes: fd8b965744 ("ASoC: wm0010: Clear IRQ as wake source and include missing header")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/5139ba1ab8c4c157ce04e56096a0f54a1683195c.1741549792.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9af152dcf1a06f589f44a74da4ad67e365d4db9a ]
Since pci_get_domain_bus_and_slot() can return NULL, add NULL check for
pci_gfx_root in the mid_get_vbt_data().
This change is similar to the checks implemented in mid_get_fuse_settings()
and mid_get_pci_revID(), which were introduced by commit 0cecdd818c
("gma500: Final enables for Oaktrail") as "additional minor
bulletproofing".
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: f910b41105 ("gma500: Add the glue to the various BIOS and firmware interfaces")
Signed-off-by: Ivan Abramov <i.abramov@mt-integration.ru>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250306112046.17144-1-i.abramov@mt-integration.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d2b9d97e89c79c95f8b517e4fa43fd100f936acc upstream.
Add qlcnic_sriov_free_vlans() in qlcnic_sriov_alloc_vlans() if
any sriov_vlans fails to be allocated.
Add qlcnic_sriov_free_vlans() to free the memory allocated by
qlcnic_sriov_alloc_vlans() if "sriov->allowed_vlans" fails to
be allocated.
Fixes: 91b7282b61 ("qlcnic: Support VLAN id config.")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Link: https://patch.msgid.link/20250307094952.14874-1-haoxiang_li2024@163.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79e31396fdd7037c503e6add15af7cb00633ea92 upstream.
[WHY & HOW]
A warning message "WARNING: CPU: 4 PID: 459 at ... /dc_resource.c:3397
calculate_phy_pix_clks+0xef/0x100 [amdgpu]" occurs because the
display_color_depth == COLOR_DEPTH_141414 is not handled. This is
observed in Radeon RX 6600 XT.
It is fixed by assigning pix_clk * (14 * 3) / 24 - same as the rests.
Also fixes the indentation in get_norm_pix_clk.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 274a87eb389f58eddcbc5659ab0b180b37e92775)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de93ddf88088f7624b589d0ff3af9effb87e8f3b upstream.
Video players (eg. mpv) do periodic XResetScreenSaver() calls to
keep the screen on while the video playing. The modesetting ddx
plumbs these straight through into the kernel as DPMS setproperty
ioctls, without any filtering whatsoever. When implemented via
atomic these end up as empty commits on the crtc (which will
nonetheless take one full frame), which leads to a dropped
frame every time XResetScreenSaver() is called.
Let's just filter out redundant DPMS property changes in the
kernel to avoid this issue.
v2: Explain the resulting commits a bit better (Sima)
Document the behaviour in uapi docs (Sima)
Cc: stable@vger.kernel.org
Testcase: igt/kms_flip/flip-vs-dpms-on-nop
Reviewed-by: Simona Vetter <simona.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250219160239.17502-1-ville.syrjala@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3e89178a9f4a80092578af3ff3c8478f9187d59 upstream.
Currently, load_microcode_amd() iterates over all NUMA nodes, retrieves their
CPU masks and unconditionally accesses per-CPU data for the first CPU of each
mask.
According to Documentation/admin-guide/mm/numaperf.rst:
"Some memory may share the same node as a CPU, and others are provided as
memory only nodes."
Therefore, some node CPU masks may be empty and wouldn't have a "first CPU".
On a machine with far memory (and therefore CPU-less NUMA nodes):
- cpumask_of_node(nid) is 0
- cpumask_first(0) is CONFIG_NR_CPUS
- cpu_data(CONFIG_NR_CPUS) accesses the cpu_info per-CPU array at an
index that is 1 out of bounds
This does not have any security implications since flashing microcode is
a privileged operation but I believe this has reliability implications by
potentially corrupting memory while flashing a microcode update.
When booting with CONFIG_UBSAN_BOUNDS=y on an AMD machine that flashes
a microcode update. I get the following splat:
UBSAN: array-index-out-of-bounds in arch/x86/kernel/cpu/microcode/amd.c:X:Y
index 512 is out of range for type 'unsigned long[512]'
[...]
Call Trace:
dump_stack
__ubsan_handle_out_of_bounds
load_microcode_amd
request_microcode_amd
reload_store
kernfs_fop_write_iter
vfs_write
ksys_write
do_syscall_64
entry_SYSCALL_64_after_hwframe
Change the loop to go over only NUMA nodes which have CPUs before determining
whether the first CPU on the respective node needs microcode update.
[ bp: Massage commit message, fix typo. ]
Fixes: 7ff6edf4fef3 ("x86/microcode/AMD: Fix mixed steppings support")
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250310144243.861978-1-revest@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a665fe3d967fe46edb4fd2497c7a5cc2dac2f55 upstream.
The device id entries for Telit FN990B ended up matching only on the
interface protocol. While this works, the protocol is qualified by the
interface class (and subclass) which should have been included.
Switch to matching using USB_DEVICE_AND_INTERFACE_INFO() while keeping
the entries sorted also by protocol for consistency.
Link: https://lore.kernel.org/20250227110655.3647028-2-fabio.porcedda@gmail.com/
Cc: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: Daniele Palmas <dnlplm@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6232f0d8e100a26275bbd773fc56a60af2c95322 upstream.
The correct name for FE990 is FE990A so use it in order to avoid
confusion with FE990B.
Cc: stable@vger.kernel.org
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18e0885bd2ca738407036434418a26a58394a60e upstream.
The Altera USB Blaster 3, available as both a cable and an on-board
solution, is primarily used for programming and debugging FPGAs.
It interfaces with host software such as Quartus Programmer,
System Console, SignalTap, and Nios Debugger. The device utilizes
either an FT2232 or FT4232 chip.
Enabling the support for various configurations of the on-board
USB Blaster 3 by including the appropriate VID/PID pairs,
allowing it to function as a serial device via ftdi_sio.
Note that this check-in does not include support for the
cable solution, as it does not support UART functionality.
The supported configurations are determined by the
hardware design and include:
1) PID 0x6022, FT2232, 1 JTAG port (Port A) + Port B as UART
2) PID 0x6025, FT4232, 1 JTAG port (Port A) + Port C as UART
3) PID 0x6026, FT4232, 1 JTAG port (Port A) + Port C, D as UART
4) PID 0x6029, FT4232, 1 JTAG port (Port B) + Port C as UART
5) PID 0x602a, FT4232, 1 JTAG port (Port B) + Port C, D as UART
6) PID 0x602c, FT4232, 1 JTAG port (Port A) + Port B as UART
7) PID 0x602d, FT4232, 1 JTAG port (Port A) + Port B, C as UART
8) PID 0x602e, FT4232, 1 JTAG port (Port A) + Port B, C, D as UART
These configurations allow for flexibility in how the USB Blaster 3 is
used, depending on the specific needs of the hardware design.
Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b654f7a51ffb386131de42aa98ed831f8c126546 ]
Device mapper bioset often has big bio_slab size, which can be more than
1000, then 8byte can't hold the slab name any more, cause the kmem_cache
allocation warning of 'kmem_cache of name 'bio-108' already exists'.
Fix the warning by extending bio_slab->name to 12 bytes, but fix output
of /proc/slabinfo
Reported-by: Guangwu Zhang <guazhang@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250228132656.2838008-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01f1d77a2630e774ce33233c4e6723bca3ae9daa ]
Keep user-forced connector status even if it cannot be programmed. Same
behavior as for the rest of the drivers.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250114100214.195386-1-tzimmermann@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9de7695925d5d2d2085681ba935857246eb2817d ]
When both of X86_LOCAL_APIC and X86_THERMAL_VECTOR are disabled,
the irq tracing produces a W=1 build warning for the tracing
definitions:
In file included from include/trace/trace_events.h:27,
from include/trace/define_trace.h:113,
from arch/x86/include/asm/trace/irq_vectors.h:383,
from arch/x86/kernel/irq.c:29:
include/trace/stages/init.h:2:23: error: 'str__irq_vectors__trace_system_name' defined but not used [-Werror=unused-const-variable=]
Make the tracepoints conditional on the same symbosl that guard
their usage.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20250225213236.3141752-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4c173dfbb6c78568578ff18f9e8822d7bd0e31b ]
Fuse allows the value of a symlink to change and this property is exploited
by some filesystems (e.g. CVMFS).
It has been observed, that sometimes after changing the symlink contents,
the value is truncated to the old size.
This is caused by fuse_getattr() racing with fuse_reverse_inval_inode().
fuse_reverse_inval_inode() updates the fuse_inode's attr_version, which
results in fuse_change_attributes() exiting before updating the cached
attributes
This is okay, as the cached attributes remain invalid and the next call to
fuse_change_attributes() will likely update the inode with the correct
values.
The reason this causes problems is that cached symlinks will be
returned through page_get_link(), which truncates the symlink to
inode->i_size. This is correct for filesystems that don't mutate
symlinks, but in this case it causes bad behavior.
The solution is to just remove this truncation. This can cause a
regression in a filesystem that relies on supplying a symlink larger than
the file size, but this is unlikely. If that happens we'd need to make
this behavior conditional.
Reported-by: Laura Promberger <laura.promberger@cern.ch>
Tested-by: Sam Lewis <samclewis@google.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Link: https://lore.kernel.org/r/20250220100258.793363-1-mszeredi@redhat.com
Reviewed-by: Bernd Schubert <bschubert@ddn.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2fe192348f93fe3a0cb1e33e4aba58e646397f4 ]
The fabric transports and also the PCI transport are not entering the
LIVE state from NEW or RESETTING. This makes the state machine more
restrictive and allows to catch not supported state transitions, e.g.
directly switching from RESETTING to LIVE.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 606572eb22c1786a3957d24307f5760bb058ca19 ]
According to the C11 standard (ISO/IEC 9899:2011, 6.5.7):
"If E1 has a signed type and E1 x 2^E2 is not representable in the result
type, the behavior is undefined."
Shifting 1 << 31 causes signed integer overflow, which leads to undefined
behavior.
Fix this by explicitly using '1U << 31' to ensure the shift operates on
an unsigned type, avoiding undefined behavior.
Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com>
Link: https://patch.msgid.link/20250218081217.3468369-1-eleanor15x@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3988ac1c67e6e84d2feb987d7b36d5791174b3da ]
The queue state checking in nvmet_rdma_recv_done is not in queue state
lock.Queue state can transfer to LIVE in cm establish handler between
state checking and state lock here, cause a silent drop of nvme connect
cmd.
Recheck queue state whether in LIVE state in state lock to prevent this
issue.
Signed-off-by: Ruozhu Li <david.li@jaguarmicro.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3fc002b206c6c83d1e3702b979733002ba6fb2c ]
rsnd_kctrl_accept_runtime() (1) is used for runtime convert rate
(= Synchronous SRC Mode). Now, rsnd driver has 2 kctrls for it
(A): "SRC Out Rate Switch"
(B): "SRC Out Rate" // it calls (1)
(A): can be called anytime
(B): can be called only runtime, and will indicate warning if it was used
at non-runtime.
To use runtime convert rate (= Synchronous SRC Mode), user might uses
command in below order.
(X): > amixer set "SRC Out Rate" on
> aplay xxx.wav &
(Y): > amixer set "SRC Out Rate" 48010 // convert rate to 48010Hz
(Y): calls B
(X): calls both A and B.
In this case, when user calls (X), it calls both (A) and (B), but it is not
yet start running. So, (B) will indicate warning.
This warning was added by commit b5c0886898 ("ASoC: rsnd: add warning
message to rsnd_kctrl_accept_runtime()"), but the message sounds like the
operation was not correct. Let's update warning message.
The message is very SRC specific, implement it in src.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://patch.msgid.link/8734gt2qed.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32ae4a2992529e2c7934e422035fad1d9b0f1fb5 ]
In some environments, the SCLP firmware interface used to query a
CHPID's configured state is not supported. On these environments,
rapidly reading the corresponding sysfs attribute produces inconsistent
results:
$ cat /sys/devices/css0/chp0.00/configure
cat: /sys/devices/css0/chp0.00/configure: Operation not supported
$ cat /sys/devices/css0/chp0.00/configure
3
This occurs for example when Linux is run as a KVM guest. The
inconsistency is a result of CIO using cached results for generating
the value of the "configure" attribute while failing to handle the
situation where no data was returned by SCLP.
Fix this by not updating the cache-expiration timestamp when SCLP
returns no data. With the fix applied, the system response is
consistent:
$ cat /sys/devices/css0/chp0.00/configure
cat: /sys/devices/css0/chp0.00/configure: Operation not supported
$ cat /sys/devices/css0/chp0.00/configure
cat: /sys/devices/css0/chp0.00/configure: Operation not supported
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Tested-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 363236d709e75610b628c2a4337ccbe42e454b6d ]
The HP 5MP Camera (USB ID 0408:5473) reports a HID sensor interface that
is not actually implemented. Attempting to access this non-functional
sensor via iio_info causes system hangs as runtime PM tries to wake up
an unresponsive sensor.
[453] hid-sensor-hub 0003:0408:5473.0003: Report latency attributes: ffffffff:ffffffff
[453] hid-sensor-hub 0003:0408:5473.0003: common attributes: 5:1, 2:1, 3:1 ffffffff:ffffffff
Add this device to the HID ignore list since the sensor interface is
non-functional by design and should not be exposed to userspace.
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b54ae69197b9f416baa0fceadff7e89075f8454 ]
The timestamps in the Firmware log and HID sensor samples are incorrect.
They show 1970-01-01 because the current IPC driver only uses the first
8 bytes of bootup time when synchronizing time with the firmware. The
firmware converts the bootup time to UTC time, which results in the
display of 1970-01-01.
In write_ipc_from_queue(), when sending the MNG_SYNC_FW_CLOCK message,
the clock is updated according to the definition of ipc_time_update_msg.
However, in _ish_sync_fw_clock(), the message length is specified as the
size of uint64_t when building the doorbell. As a result, the firmware
only receives the first 8 bytes of struct ipc_time_update_msg.
This patch corrects the length in the doorbell to ensure the entire
ipc_time_update_msg is sent, fixing the timestamp issue.
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
