When SAP starts on 5G, initialize SAP mandatory list with
2G and 5G mandatory list. And also select same band channel
SCC channel firstly in the intersection of PCL and mandatory
channel list.
Change-Id: Iac86b5caf38bf72f143be81122f8378fc61b29e2
CRs-Fixed: 3039268
During enumeration all adapters, if adapter is not "up",
it is unnecessary to check connecting or not. Otherwise,
the vdev is not created for the adapter and the
sme_roaming_in_progress will output "ROAM: incorrect vdev ID"
error message.
Change-Id: I3df5379a7d0b88c439d49711c36000717c7a433b
CRs-Fixed: 3002674
As dynamic allocation occupy cnss prealloc memory, which may
cause this prealloc pool to be exhausted.
Move dynamic memory to static.
Change-Id: Ib05c044f8c0c805148d832f54c09915ef9b4c98b
CRs-Fixed: 3174282
TWT is not disabled for certain APs. Add OUIs of the
APs to configuration file.
Change-Id: I3bb2238550294b443f166920069a14fb81e6873d
CRs-Fixed: 3176212
Add support to enable the "FT over DS" via
QCA_WLAN_VENDOR_ATTR_CONFIG_FT_OVER_DS vendor config
command.
This configuration helps the firmware to support
“FT over DS” instead of “FT over Air”
Change-Id: I493bf15f83bc39135aaeefa9d8ef328f0fc0cda3
CRs-Fixed: 2968680
Sometimes TX/RX pkt statistics workqueue may be delayed.
The workqueue interval value is pre-defined and is used
for bandwidth vote. If the interval is inaccurate, whole
pkts statistics are not accurate, bus bandwidth vote is
wrong also. This change is aimed to use absolute workqueue
time delay instead of pre-defined value to get accurate
packets per milliseconds result.
Change-Id: I2b730fc36d4b5c42742ed9107d9a7e1f95eb4988
CRs-Fixed: 2976857
Currently driver frees the radio stats memory from wma
in error cases, there is a possibility that if hdd gets
time out for the stats request, it tries to free the radio
stats memory and at the same time if wma receives invalid
stats from fw in that case wma also tries to free the radio
stats memory which may lead to double free.
To aoid above issue, do not free the radio stats memory from
wma, in error cases hdd will free this memory after it gets
time out.
Change-Id: I6f6073a1a8e0be1b87efce288b7567e8fc8d69b0
CRs-Fixed: 3013842
Reject any incoming get_all_peers TDLS command if there
are any currently in progress.
The later commands will only be processed once the earlier
commands finish, since they are processed sequentially.
However, once a command finishes, the memory allocated for
it from userspace is freed up. Each command is passed the
same address so the later commands will end up writing to
a freed address. To avoid this, reject incoming requests
if there are any still in progress.
For this, the condition should be corrected.
We shouldn't use completion_done here for checking for
completion as this will always return false, as
tdls_user_cmd_comp.done will remain in init state always.
So, the very first command will also not work.
In general completion_done is used to check if there are
multiple threads waiting on the complete event that's
why it will return true only when tdls_user_cmd_comp.done
is set with complete().
Also, if the state is in wait_for_completion, this function
will return true after the wait timer is over or condition
is met as wait_for_completion will hold out the hold lock
and will will prevent completion_done from returning.
Better to use a flag to determine command condition.
Change-Id: I1b6b270dbb9b0b103f10e7ae22a60030ea2fbb98
CRs-Fixed: 3162184
Enable global IPA structure, g_ipa_config only if it is
enabled in both platform driver and ini file.
Change-Id: I1bd4e03eadf420f736bb91478b0f2e04bcd60ebd
CRs-Fixed: 3148820
For IPCI_FW_SIM, HOST is not sending WMI_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID to
FW. To wakeup HOST after suspend add api pld_ipci_fw_sim_exit_power_save
to redirect HOST wakeup.
Change-Id: Iaec5c947c5f3c1fd23dc5b31801ff94612fb7c47
CRs-Fixed: 3039189
When SAE authentication fails due to some reason and if the
failure is detected while processing confirm request from the
station, some APs send deauth instead of confirm response.
Current driver/wpa_suplicant wait for the confirm response and
driver drops the deauth frame as it's in the middle of SAE
authentication. This results in connect timeout.
Driver is supposed to process the deauth from AP and indicate
failure to userspace. To resolve this, consider the deauth from AP
as SAE failure and abort the connection. Send connect failure to
userspace.
CRs-Fixed: 3157178
Change-Id: I09c9d8b19539e4986665c6052d3a7f52b3e49600
Currently min_dwell_time_6g ini support is there only for normal
scan.
Added support to configure min_dwell_time_6g in roam offload scan.
Change-Id: I7da5fff738dbaf2a28a909e58ab6c797724ccfaf
CRs-Fixed: 3156597
Currently during fisa flow aggregation REO ID check is done to
make sure all the flow packets are received in same REO and to avoid
out of order reception. But if RX packet matches CCE rules REO ID
is selected based on CCE rules since they have higher priority.
In this case ignore RX packet for FISA aggregation and do not panic.
Change-Id: I09b5c9fc4ecff7223d0034921e8923776ae4bf3b
CRs-Fixed: 3153104
In dual SAP connection, calls only disable_pipes to disable IPA,
whereas during second SAP disconnection, to enable IPA, calls
wlan_ipa_uc_handle_first_con, which sends ipa_set_active MSG
as true to FW, for both Tx/Rx to resume.
So calling wlan_ipa_uc_handle_last_discon in dual SAP mode,
which sends ipa_set_active MSG as false to FW, to suspend.
Change-Id: I224e94a003030f497e15f242634f15d9c71b9ef0
CRs-Fixed: 3094276
Fix hdd_ctx null pointer derefernce issue in hdd bus suspend
related code by addition of hdd_ctx null check before its use.
Change-Id: Iea92dcdf8591e61853af233f8e28fe7e0f9ec4bf
CRs-Fixed: 3144126
Set nan_separate_iface_support flag in FTM mode to avoid
create NAN vdev in FTM mode. This helps in FTM mode test cases
where max supported vdevs are used.
Change-Id: Ia628655a87505db787043ef29dd18d259052b521
CRs-Fixed: 2888703
This reverts commit I06ea617df49287ee87e7b5bf8b20971b581dedf1
which introduced a fix to enable/disable arp offload on every
suspend/resume even if gActiveModeOffload is enabled, which is
not correct. The expectation here is that if gActiveModeOffload
is enabled, host should enable arp offload only onece and it
should not disable on any condition.
Change-Id: Ifc4ff1c0a39cc4c17e9a292ef8b0ebabd766a710
CRs-Fixed: 3147896
Dynamic GRO feature is enabled by default and aimed for specific
customers. Add an ini control to allow other customers to config
this feature enable/disable.
Change-Id: I83edd69d0e30d5944f0724ed8350328abff619bb
CRs-Fixed: 3070912
It may cause out of bound access if length exceed
SIR_MAX_BEACON_SIZE.
Add length check to protect that.
Change-Id: I6581b62aa8b380a0f1195a16515ad635a9154023
CRs-Fixed: 3147267
Reject any incoming get_all_peers TDLS command if there are any
currently in progress.
The later commands will only be processed once the earlier commands
finish, since they are processed sequentially. However, once a
command finishes, the memory allocated for it from userspace is freed
up. Each command is passed the same address so the later commands will
end up writing to a freed address. To avoid this, reject incoming
requests if there are any still in progress.
Change-Id: I6970e3b73c6ce5afc921edaaf477825928800342
CRs-Fixed: 3150044
Reduce the log level for the frequent acceptable errors
to reduce the roam latencies
Change-Id: I9f5405025948d160e6fcd65ecca05dce7670ea84
CRs-Fixed: 3150439
Make sure the parsed association request array is valid at the
association ID index, before dereferencing it. This will prevent NULL
pointer deref. There is already a check for the beginning of the parsed
assoc req array, but it is not checking at the assoc ID index.
Change-Id: Icac3b2a4a0646dec4c64a2224e3271b0842a8194
CRs-Fixed: 3147273
In case of PNO scan, If firmware supports
WMI_SERVICE_PNO_SCAN_CONFIG_PER_CHANNEL, it uses the
upper-12 bits(bit-20 to bit 32) of channel_list for
flags and lower 20-bits(bit-0 to bit-19) for frequency.
If firmware doesn't support it, then channel_list holds
the frequency value only.
Fix is to fill the flags and frequency accordingly.
Change-Id: I8473072069da4532406ce720a0070a665e29b1af
CRs-Fixed: 3103939
Reduce stack frame size of wlan_update_bss_with_fils_data()
by allocating dynamic memory to fils indication.
Change-Id: I799100558b4192f4be2eaa1fb4f9508a2cb73e66
CRs-Fixed: 3123325
