Currently -DWLAN_FEATURE_GTK_OFFLOAD is being set twice, once
unconditionally and once based upon CONFIG_GTK_OFFLOAD. Since this is
properly featurized, remove the unconditional setting so that the
setting is correctly controlled by the configuration.
Change-Id: I6f820990dc48304f18f78ec59005c2188a677094
CRs-Fixed: 2223858
Currently -DWLAN_ENABLE_AGEIE_ON_SCAN_RESULTS is unconditionally added
to all builds. Since this feature may not be required for all targets,
create a CONFIG_AGEIE_ON_SCAN_RESULTS feature flag to enable this
feature.
Change-Id: Id5a82a85f4484ca710d4b309355fe3ee0d05883e
CRs-Fixed: 2223857
Currently Kbuild sets a HAVE_CFG80211 flag based upon whether or not
CONFIG_CFG80211 is configured. The presence of this flag implies that
cfg80211 is optional. However in reality this is a required module, so
remove the confusing flag and instead make the underlying code always
present.
Change-Id: Ia039968cad6f311091e09d4b82805c7bbc5b83f8
CRs-Fixed: 2223856
WMI non_tlv is not used for MCL targets and hence compile
out WMI non_tlv object file from Kbuild.
Change-Id: I0ee9376065dffb0f959ef8ba47435cc38a3d7d55
CRs-Fixed: 2216856
Currently the switch -DFEATURE_SKB_PRE_ALLOC is inferred by examining
three different configuration options. In order to clearly separate
setting the configuration from applying the configuration create a new
CONFIG_FEATURE_SKB_PRE_ALLOC configuration parameter.
Change-Id: I301031a03fdae394748cf4cb6259044324eec6f1
CRs-Fixed: 2222914
While handling a multi-segment TSO packet, there is a race condition
where, if tx complete arrives fast enough, the un-sent TSO segments
may be lost forever and a previously sent segment would be attempted
to be sent over.
Fix the race condition. Dont use the segment after send to go to the
next one.
Change-Id: I4abd9d26f50c749141925894a8845cf82df4d222
CRs-Fixed: 2168778
Currently non-linear, non-tso TX data is not handled correctly,
only the non-tso, single linear data is supported. the frag paged
data in skb is missed while packet length for HW access
is entire packet length, HW DMA failed.
temporarily to linearize skb so that non-linear data could be TX
correctly.
Change-Id: Ic0f2b7a0b021ca190c870551a66181f50ae72c65
CRs-Fixed: 2180318
Suspend/Resume unit test IOCTLs and other unit test features are only
enabled in defconfig debug builds and always disabled in production
builds. Add CFG INI item to disable these test IOCTLs even in defconfig
build such that by default on all build combinations unit test IOCTLs
are always disabled.
Change-Id: I71a63d2b85800b630d7c18eb77a3cffddcd66fbb
CRs-Fixed: 2221874
Currently the switch -DFEATURE_WLAN_D0WOW is inferred by examining two
different configuration options. In order to clearly separate setting
the configuration from applying the configuration create a new
CONFIG_FEATURE_WLAN_D0WOW configuration parameter.
Change-Id: Ie278011a309a18673eabb4bc4f8f8bb691815018
CRs-Fixed: 2222913
Secondary bit map starts with color 32, So current color minus 31
will shift color bit beyond the expected position which is 0th,
Fix it by subtracting with 32 instead 31.
Change-Id: I7ede16faee129c42c71d490f653244398061a8b6
CRs-Fixed: 2222003
If connection is in progress and new connection req is
received from supplicant, hdd tries to disconnect the
current session and post force disassoc command and wait
for it to get completed. If the current ongoing connect
operation fails and this force disassoc is processed as
sme session is in disconnected state it is silently
dropped and thus there is no event sent to the HDD
to stop the wait for disconnect and HDD wait for 5
sec before returning connect failure.
Fix this by Calling disconnect handler if, disconnect
with force dissoc is called in disconnected state
Change-Id: I3a78308b54fb048fba5a6aed3d8e8b193c371647
CRs-Fixed: 2223313
Currently the switch -DENABLE_SMMU_S1_TRANSLATION is inferred by
examining two different configuration options. In order to clearly
separate setting the configuration from applying the configuration
create a new CONFIG_ENABLE_SMMU_S1_TRANSLATION configuration
parameter.
Change-Id: Ibfa0cfbad5342895d90a32ddcf46a9d851253dcb
CRs-Fixed: 2222912
In Kbuild CONFIG_ROME_IF is used to calculate the interface used by
the WLAN hardware. Once this is determined, one of the boolean
CONFIG_HIF_[PCI|USB|SDIO|SNOC|...] variables is configured. In
anticipation of refactoring the Kbuild in a manner which will remove
the necessity of having CONFIG_ROME_IF, replace all tests of
CONFIG_ROME_IF with tests of CONFIG_HIF_* once the CONFIG_HIF_*
variables have been set.
Change-Id: If80d465500b6b99181d470fa6bff3dc8c20e4409
CRs-Fixed: 2222911
Currently WAPI support is being unconditionally enabled in the
driver. However support may not be required on all targets, so add a
configuration flag
Change-Id: I1344620d4cff38dc9d780c9a272d2de07a423e8d
CRs-Fixed: 2222910
There is a chance that kernel can trigger suspend while
connection in progress. If driver allows this suspend, this can
result in fw panic.
Specific scenario:
If driver allows suspend to go when it waits for probe response,
fw least expects suspend indication as fw is in vdev start state.
This unexpected suspend indication in vdev start state can cause
fw panic.
Hold wakelock till the completion of association to fix this issue.
Change-Id: I168ead2ab1ef4fff1d9af3f3142c82536c3f4798
CRs-Fixed: 2217140
qcacld-2.0 to qcacld-3.0 propagation
Discard the original wmi interface:
WMI_PEER_ANTDIV_INFO_REQ_CMDID/PEER_ANTDIV_INFO_EVENTID,
replace with the new one:
WMI_PDEV_DIV_GET_RSSI_ANTID_CMDID/WMI_PDEV_DIV_RSSI_ANTID_EVENTID
to support chain value along with corresponding antenna info.
Change-Id: Ie9ea9d160e1ac1e2e65de422c85989159fb5a556
CRs-Fixed: 2005820
When CLD3.2 driver is setting pdev burst mode to FW, 3
possible values are supported:
0: disabled
1: enabled for legacy burst
3: enabled for SIFS burst
but the iwpriv command handling code only supports setting
0 or 1 to FW.
Add value checking for WE_SET_BURST_ENABLE to support setting
3 to FW.
Change-Id: I35506b83d584f6e8d066adfc43df8dd03ce54661
CRs-Fixed: 2214992
When CONFIG_MOBILE_ROUTER feature is enabled, FEATURE_WLAN_TDLS is
turned off. As a result, compiler complains no prototype for
lim_disassoc_tdls_peers error.
Fix is to define lim_disassoc_tdls_peers as static inline when
FEATURE_WLAN_TDLS is not defined.
Change-Id: Idad1f7d2e27853307750fcc7ffbe7ab1e3504c3b
CRs-Fixed: 2215100
Currently in Kbuild the "profile" variable CONFIG_MOBILE_ROUTER is
defined based upon a set of tests. Subsequently CDEFINES is updated
with specific feature flags based upon the CONFIG_MOBILE_ROUTER
value. In anticipation of refactoring profile information into
per-target configuration files, create a separate configuration
variable for each feature that is currently controlled by
CONFIG_MOBILE_ROUTER. This will allow each target to have fine-grain
control over its features.
Change-Id: I5fb78f8c49c9ea2b970e547049d565cc1e9243f0
CRs-Fixed: 2222151
CONFIG_CNSS_EOS is an obsolete configuration item so remove all
references to it.
Change-Id: Id26ac1fb6969af845730b57f1bef6a4903c2b71e
CRs-Fixed: 2222022
Currently if the driver is built directly within the kernel the
following Kconfig parameters will NOT be taken from the kernel
configuration:
- CONFIG_HELIUMPLUS
- CONFIG_64BIT_PADDR
- CONFIG_FEATURE_TSO
- CONFIG_FEATURE_TSO_DEBUG
Inversely, if the driver is built outside the kernel the following
parameter does not enforce the "depends on HELIUMPLUS" that is found
in the Kconfig:
- CONFIG_WLAN_LRO
Resolve these issues by relocating the HELIUMPLUS definition to inside
the "ifeq ($(KERNEL_BUILD), n)" portion of the Kbuild, and relocating
the other configurations such that they only get initialized when
HELIUMPLUS is enabled.
Change-Id: Ie41cd0a59bfa39fed39779e508bebbd6e29f6c0c
CRs-Fixed: 2222020
CONFIG_SUPPORT_HOST_STATISTICS is set but then never referenced, so
remove it from Kbuild.
Change-Id: Ib2ec5dfe1a1e10e04116b097296c5bacc6ece9cd
CRs-Fixed: 2221853
Currently Kbuild unconditionally sets -DHAL_SELF_STA_PER_BSS=1. There
is only one place where this macro is referenced, and it actually
requires that the macro be set for the driver to work. Since this
logic isn't really conditional, remove the conditional compilation.
Change-Id: I09a03339df086146b81b3012fb281e166fccd5da
CRs-Fixed: 2221852
Kbuild has conditional logic to set CONFIG_HIF_MESSAGE_BASED which is
subsequently used to pass -DHIF_MESSAGE_BASED to the driver. But
HIF_MESSAGE_BASED is not actually used by the driver, so remove this
support.
Change-Id: Id0650c2c44d7b20d58b30e405c2e8f4aa1082e99
CRs-Fixed: 2221851
Kbuild conditionally defines CONFIG_PRIMA_WLAN_11AC_HIGH_TP but then
never uses it. Since it is obsolete, remove it.
Change-Id: I4002197c3068c58e542ab0b7bcc55b642e04624c
CRs-Fixed: 2221850
In Kbuild, configuration variables are used to determine which files
are included in the build and what flags are given to the C compiler.
Currently most of the configuration variables are set in the top
portion of the file. In preparation for futher featurization identify
those configuration variables which are being set in the bottom
portion of the file, and relocate them to the top portion of the file.
Change-Id: I962edf666ba7ed8c37a28e448b8675249a759975
CRs-Fixed: 2220924
Fix the following issues in Kbuild:
- 'Managment' may be misspelled - perhaps 'Management'?
- 'Endianess' may be misspelled - perhaps 'Endianness'?
- Use of EXTRA_CFLAGS is deprecated, please use `ccflags-y instead.
Change-Id: Ie2d2940bbf5b143b2185bf88bc8fd33abb16817a
CRs-Fixed: 2220923
In the Kbuild most of the local flag variables use y/n but there are
some that use 0/1. For consistency change all 0/1 flags to y/n.
Change-Id: Ic436d7f1cf8a75eae9d3542b458094ed6442740d
CRs-Fixed: 2220922
Kbuild currently has conditional code that is used to set the macro
AH_BYTE_ORDER. But this macro is unused by the code, so remove it.
Change-Id: If694bdb492645eda5d314f7240e42677d9e4413d
CRs-Fixed: 2220921
There are a multitude of endian macros currently supported by the
driver. Consolidate them in one place as a precursor to future
consolidation.
Change-Id: Id4e57eb6e409aa0c84d46b8ce9eb85f3be56716e
CRs-Fixed: 2220920
Kbuild currently passes the macro SPECTRAL_USE_NETLINK_SOCKETS to the
compiler. However this macro is now obsolete, so remove it.
Change-Id: Id88028cceddcaaf8f35c708451fa5bf21c4695dd
CRs-Fixed: 2220919
