commit 6599b6a6fa8060145046d0744456b6abdb3122a7 upstream.
The stream contex type (SCT) bitfield is used both in the stream context
data structure, and in the 'Set TR Dequeue pointer' command TRB.
In both cases it uses bits 3:1
The SCT_FOR_TRB(p) macro used to set the stream context type (SCT) field
for the 'Set TR Dequeue pointer' command TRB incorrectly shifts the value
1 bit left before masking the three bits.
Fix this by first masking and rshifting, just like the similar
SCT_FOR_CTX(p) macro does
This issue has not been visibile as the lost bit 3 is only used with
secondary stream arrays (SSA). Xhci driver currently only supports using
a primary stream array with Linear stream addressing.
Fixes: 95241dbdf8 ("xhci: Set SCT field for Set TR dequeue on streams")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c1dda2acc4192d826e84008d963b528e24d12bc upstream.
Fake CSR controllers don't seem to handle short-transfer properly which
cause command to time out:
kernel: usb 1-1: new full-speed USB device number 19 using xhci_hcd
kernel: usb 1-1: New USB device found, idVendor=0a12, idProduct=0001, bcdDevice=88.91
kernel: usb 1-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
kernel: usb 1-1: Product: BT DONGLE10
...
Bluetooth: hci1: Opcode 0x1004 failed: -110
kernel: Bluetooth: hci1: command 0x1004 tx timeout
According to USB Spec 2.0 Section 5.7.3 Interrupt Transfer Packet Size
Constraints a interrupt transfer is considered complete when the size is 0
(ZPL) or < wMaxPacketSize:
'When an interrupt transfer involves more data than can fit in one
data payload of the currently established maximum size, all data
payloads are required to be maximum-sized except for the last data
payload, which will contain the remaining data. An interrupt transfer
is complete when the endpoint does one of the following:
• Has transferred exactly the amount of data expected
• Transfers a packet with a payload size less than wMaxPacketSize or
transfers a zero-length packet'
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219365
Fixes: 7b05933340f4 ("Bluetooth: btusb: Fix not handling ZPL/short-transfer")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb143d05def52bc6d193e813018e5fa1a0e47c77 upstream.
This driver makes use of triggered buffers, but does not select the
required modules.
Add the missing 'select IIO_BUFFER' and 'select IIO_TRIGGERED_BUFFER'.
Fixes: e717f8c6df ("iio: adc: Add the TI ads124s08 ADC code")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241003-iio-select-v1-3-67c0385197cd@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75461a0b15d7c026924d0001abce0476bbc7eda8 upstream.
This driver makes use of triggered buffers, but does not select the
required modules.
Add the missing 'select IIO_BUFFER' and 'select IIO_TRIGGERED_BUFFER'.
Fixes: 16b0526153 ("mb1232.c: add distance iio sensor with i2c")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241003-iio-select-v1-13-67c0385197cd@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 530688e39c644543b71bdd9cb45fdfb458a28eaa upstream.
The opt3001 driver uses predetermined full-scale range values to
determine what exponent to use for event trigger threshold values.
The problem is that one of the values specified in the datasheet is
missing from the implementation. This causes larger values to be
scaled down to an incorrect exponent, effectively reducing the
maximum settable threshold value by a factor of 2.
Add missing full-scale range array value.
Fixes: 94a9b7b180 ("iio: light: add support for TI's opt3001 light sensor")
Signed-off-by: Emil Gedenryd <emil.gedenryd@axis.com>
Cc: <Stable@vger.kernel.org>
Link: https://patch.msgid.link/20240913-add_opt3002-v2-1-69e04f840360@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a29b84cf7fbf912a6ab1b9c886746f02b74ea25 upstream.
If hid_sensor_set_report_latency() fails, the error code should be returned
instead of a value likely to be interpreted as 'success'.
Fixes: 138bc7969c ("iio: hid-sensor-hub: Implement batch mode")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/c50640665f091a04086e5092cf50f73f2055107a.1727980825.git.christophe.jaillet@wanadoo.fr
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c4834fd8696a949d1b1f1c2c5b96e1ad2083b02 upstream.
This driver makes use of triggered buffers, but does not select the
required modules.
Fixes: 2a86487786 ("iio: adc: ti-ads8688: add trigger and buffer support")
Add the missing 'select IIO_BUFFER' and 'select IIO_TRIGGERED_BUFFER'.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20241003-iio-select-v1-4-67c0385197cd@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27b6aa68a68105086aef9f0cb541cd688e5edea8 upstream.
This driver makes use of regmap_mmio, but does not select the required
module.
Add the missing 'select REGMAP_MMIO'.
Fixes: 4d4b30526e ("iio: dac: add support for stm32 DAC")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241003-ad2s1210-select-v1-8-4019453f8c33@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 252ff06a4cb4e572cb3c7fcfa697db96b08a7781 upstream.
This driver makes use of regmap_spi, but does not select the required
module.
Add the missing 'select REGMAP_SPI'.
Fixes: 8316cebd1e ("iio: dac: add support for ltc1660")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241003-ad2s1210-select-v1-7-4019453f8c33@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26498b8d54373d31a621d7dec95c4bd842563b3b upstream.
Currently if condition (!bo and !vmw_kms_srf_ok()) was met
we go to err_out with ret == 0.
err_out dereferences vfb if ret == 0, but in our case vfb is still NULL.
Fix this by assigning sensible error to ret.
Found by Linux Verification Center (linuxtesting.org) with SVACE
Signed-off-by: Nikolay Kuratov <kniv@yandex-team.ru>
Cc: stable@vger.kernel.org
Fixes: 810b3e1683 ("drm/vmwgfx: Support topology greater than texture size")
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241002122429.1981822-1-kniv@yandex-team.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e972b08b91ef48488bae9789f03cfedb148667fb upstream.
We're seeing crashes from rq_qos_wake_function that look like this:
BUG: unable to handle page fault for address: ffffafe180a40084
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 100000067 P4D 100000067 PUD 10027c067 PMD 10115d067 PTE 0
Oops: Oops: 0002 [#1] PREEMPT SMP PTI
CPU: 17 UID: 0 PID: 0 Comm: swapper/17 Not tainted 6.12.0-rc3-00013-geca631b8fe80 #11
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
RIP: 0010:_raw_spin_lock_irqsave+0x1d/0x40
Code: 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa 0f 1f 44 00 00 41 54 9c 41 5c fa 65 ff 05 62 97 30 4c 31 c0 ba 01 00 00 00 <f0> 0f b1 17 75 0a 4c 89 e0 41 5c c3 cc cc cc cc 89 c6 e8 2c 0b 00
RSP: 0018:ffffafe180580ca0 EFLAGS: 00010046
RAX: 0000000000000000 RBX: ffffafe180a3f7a8 RCX: 0000000000000011
RDX: 0000000000000001 RSI: 0000000000000003 RDI: ffffafe180a40084
RBP: 0000000000000000 R08: 00000000001e7240 R09: 0000000000000011
R10: 0000000000000028 R11: 0000000000000888 R12: 0000000000000002
R13: ffffafe180a40084 R14: 0000000000000000 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff9aaf1f280000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffafe180a40084 CR3: 000000010e428002 CR4: 0000000000770ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<IRQ>
try_to_wake_up+0x5a/0x6a0
rq_qos_wake_function+0x71/0x80
__wake_up_common+0x75/0xa0
__wake_up+0x36/0x60
scale_up.part.0+0x50/0x110
wb_timer_fn+0x227/0x450
...
So rq_qos_wake_function() calls wake_up_process(data->task), which calls
try_to_wake_up(), which faults in raw_spin_lock_irqsave(&p->pi_lock).
p comes from data->task, and data comes from the waitqueue entry, which
is stored on the waiter's stack in rq_qos_wait(). Analyzing the core
dump with drgn, I found that the waiter had already woken up and moved
on to a completely unrelated code path, clobbering what was previously
data->task. Meanwhile, the waker was passing the clobbered garbage in
data->task to wake_up_process(), leading to the crash.
What's happening is that in between rq_qos_wake_function() deleting the
waitqueue entry and calling wake_up_process(), rq_qos_wait() is finding
that it already got a token and returning. The race looks like this:
rq_qos_wait() rq_qos_wake_function()
==============================================================
prepare_to_wait_exclusive()
data->got_token = true;
list_del_init(&curr->entry);
if (data.got_token)
break;
finish_wait(&rqw->wait, &data.wq);
^- returns immediately because
list_empty_careful(&wq_entry->entry)
is true
... return, go do something else ...
wake_up_process(data->task)
(NO LONGER VALID!)-^
Normally, finish_wait() is supposed to synchronize against the waker.
But, as noted above, it is returning immediately because the waitqueue
entry has already been removed from the waitqueue.
The bug is that rq_qos_wake_function() is accessing the waitqueue entry
AFTER deleting it. Note that autoremove_wake_function() wakes the waiter
and THEN deletes the waitqueue entry, which is the proper order.
Fix it by swapping the order. We also need to use
list_del_init_careful() to match the list_empty_careful() in
finish_wait().
Fixes: 38cfb5a45e ("blk-wbt: improve waking of tasks")
Cc: stable@vger.kernel.org
Signed-off-by: Omar Sandoval <osandov@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/d3bee2463a67b1ee597211823bf7ad3721c26e41.1729014591.git.osandov@fb.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff898623af2ed564300752bba83a680a1e4fec8d upstream.
AMD's initial implementation of IBPB did not clear the return address
predictor. Beginning with Zen4, AMD's IBPB *does* clear the return address
predictor. This behavior is enumerated by CPUID.80000008H:EBX.IBPB_RET[30].
Define X86_FEATURE_AMD_IBPB_RET for use in KVM_GET_SUPPORTED_CPUID,
when determining cross-vendor capabilities.
Suggested-by: Venkatesh Srinivas <venkateshs@chromium.org>
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cad4b3d4ab1f062708fff33f44d246853f51e966 upstream.
The parameters for the diag 0x258 are real addresses, not virtual, but
KVM was using them as virtual addresses. This only happened to work, since
the Linux kernel as a guest used to have a 1:1 mapping for physical vs
virtual addresses.
Fix KVM so that it correctly uses the addresses as real addresses.
Cc: stable@vger.kernel.org
Fixes: 8ae04b8f50 ("KVM: s390: Guest's memory access functions get access registers")
Suggested-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Signed-off-by: Nico Boehr <nrb@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20240917151904.74314-3-nrb@linux.ibm.com
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dee3df68ab4b00fff6bdf9fc39541729af37307c upstream.
According to the VT220 specification the possible character combinations
sent on RETURN are only CR or CRLF [0].
The Return key sends either a CR character (0/13) or a CR
character (0/13) and an LF character (0/10), depending on the
set/reset state of line feed/new line mode (LNM).
The sclp/vt220 driver however uses LFCR. This can confuse tools, for
example the kunit runner.
Link: https://vt100.net/docs/vt220-rm/chapter3.html#S3.2
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Link: https://lore.kernel.org/r/20241014-s390-kunit-v1-2-941defa765a6@linutronix.de
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49f683b41f28918df3e51ddc0d928cb2e934ccdb upstream.
Use {READ,WRITE}_ONCE() to access kvm->last_boosted_vcpu to ensure the
loads and stores are atomic. In the extremely unlikely scenario the
compiler tears the stores, it's theoretically possible for KVM to attempt
to get a vCPU using an out-of-bounds index, e.g. if the write is split
into multiple 8-bit stores, and is paired with a 32-bit load on a VM with
257 vCPUs:
CPU0 CPU1
last_boosted_vcpu = 0xff;
(last_boosted_vcpu = 0x100)
last_boosted_vcpu[15:8] = 0x01;
i = (last_boosted_vcpu = 0x1ff)
last_boosted_vcpu[7:0] = 0x00;
vcpu = kvm->vcpu_array[0x1ff];
As detected by KCSAN:
BUG: KCSAN: data-race in kvm_vcpu_on_spin [kvm] / kvm_vcpu_on_spin [kvm]
write to 0xffffc90025a92344 of 4 bytes by task 4340 on cpu 16:
kvm_vcpu_on_spin (arch/x86/kvm/../../../virt/kvm/kvm_main.c:4112) kvm
handle_pause (arch/x86/kvm/vmx/vmx.c:5929) kvm_intel
vmx_handle_exit (arch/x86/kvm/vmx/vmx.c:?
arch/x86/kvm/vmx/vmx.c:6606) kvm_intel
vcpu_run (arch/x86/kvm/x86.c:11107 arch/x86/kvm/x86.c:11211) kvm
kvm_arch_vcpu_ioctl_run (arch/x86/kvm/x86.c:?) kvm
kvm_vcpu_ioctl (arch/x86/kvm/../../../virt/kvm/kvm_main.c:?) kvm
__se_sys_ioctl (fs/ioctl.c:52 fs/ioctl.c:904 fs/ioctl.c:890)
__x64_sys_ioctl (fs/ioctl.c:890)
x64_sys_call (arch/x86/entry/syscall_64.c:33)
do_syscall_64 (arch/x86/entry/common.c:?)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
read to 0xffffc90025a92344 of 4 bytes by task 4342 on cpu 4:
kvm_vcpu_on_spin (arch/x86/kvm/../../../virt/kvm/kvm_main.c:4069) kvm
handle_pause (arch/x86/kvm/vmx/vmx.c:5929) kvm_intel
vmx_handle_exit (arch/x86/kvm/vmx/vmx.c:?
arch/x86/kvm/vmx/vmx.c:6606) kvm_intel
vcpu_run (arch/x86/kvm/x86.c:11107 arch/x86/kvm/x86.c:11211) kvm
kvm_arch_vcpu_ioctl_run (arch/x86/kvm/x86.c:?) kvm
kvm_vcpu_ioctl (arch/x86/kvm/../../../virt/kvm/kvm_main.c:?) kvm
__se_sys_ioctl (fs/ioctl.c:52 fs/ioctl.c:904 fs/ioctl.c:890)
__x64_sys_ioctl (fs/ioctl.c:890)
x64_sys_call (arch/x86/entry/syscall_64.c:33)
do_syscall_64 (arch/x86/entry/common.c:?)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
value changed: 0x00000012 -> 0x00000000
Fixes: 217ece6129 ("KVM: use yield_to instead of sleep in kvm_vcpu_on_spin")
Cc: stable@vger.kernel.org
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240510092353.2261824-1-leitao@debian.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Saeed Mirzamohammadi <saeed.mirzamohammadi@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31db78a4923ef5e2008f2eed321811ca79e7f71b upstream.
When ieee80211_key_link() is called by ieee80211_gtk_rekey_add()
but returns 0 due to KRACK protection (identical key reinstall),
ieee80211_gtk_rekey_add() will still return a pointer into the
key, in a potential use-after-free. This normally doesn't happen
since it's only called by iwlwifi in case of WoWLAN rekey offload
which has its own KRACK protection, but still better to fix, do
that by returning an error code and converting that to success on
the cfg80211 boundary only, leaving the error for bad callers of
ieee80211_gtk_rekey_add().
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: fdf7cb4185 ("mac80211: accept key reinstall without changing anything")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Sherry: bp to fix CVE-2023-52530, resolved minor conflicts in
net/mac80211/cfg.c because of context change due to missing commit
23a5f0af6ff4 ("wifi: mac80211: remove cipher scheme support")
ccdde7c74ffd ("wifi: mac80211: properly implement MLO key handling")]
Signed-off-by: Sherry Yang <sherry.yang@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7528c4fb1237512ee18049f852f014eba80bbe8d upstream.
I got a bad pud error and lost a 1GB HugeTLB when calling swapoff. The
problem can be reproduced by the following steps:
1. Allocate an anonymous 1GB HugeTLB and some other anonymous memory.
2. Swapout the above anonymous memory.
3. run swapoff and we will get a bad pud error in kernel message:
mm/pgtable-generic.c:42: bad pud 00000000743d215d(84000001400000e7)
We can tell that pud_clear_bad is called by pud_none_or_clear_bad in
unuse_pud_range() by ftrace. And therefore the HugeTLB pages will never
be freed because we lost it from page table. We can skip HugeTLB pages
for unuse_vma to fix it.
Link: https://lkml.kernel.org/r/20241015014521.570237-1-liushixin2@huawei.com
Fixes: 0fe6e20b9c ("hugetlb, rmap: add reverse mapping for hugepage")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Acked-by: Muchun Song <muchun.song@linux.dev>
Cc: Naoya Horiguchi <nao.horiguchi@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9246b487ab3c3b5993aae7552b7a4c541cc14a49 upstream.
Add DMA support for audio function of Glenfly Arise chip, which uses
Requester ID of function 0.
Link: https://lore.kernel.org/r/CA2BBD087345B6D1+20240823095708.3237375-1-wangyuli@uniontech.com
Signed-off-by: SiyuLi <siyuli@glenfly.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
[bhelgaas: lower-case hex to match local code, drop unused Device IDs]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 926fe783c8a64b33997fec405cf1af3e61aed441 upstream.
Recent changes to count number of matching symbols when creating
a kprobe event failed to take into account kernel modules. As such, it
breaks kprobes on kernel module symbols, by assuming there is no match.
Fix this my calling module_kallsyms_on_each_symbol() in addition to
kallsyms_on_each_match_symbol() to perform a proper counting.
Link: https://lore.kernel.org/all/20231027233126.2073148-1-andrii@kernel.org/
Cc: Francis Laniel <flaniel@linux.microsoft.com>
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Fixes: b022f0c7e404 ("tracing/kprobes: Return EADDRNOTAVAIL when func matches several symbols")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Song Liu <song@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
[ Sherry: It's a fix for previous backport, thus backport together to 5.4.y ]
Signed-off-by: Sherry Yang <sherry.yang@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b022f0c7e404887a7c5229788fc99eff9f9a80d5 upstream.
When a kprobe is attached to a function that's name is not unique (is
static and shares the name with other functions in the kernel), the
kprobe is attached to the first function it finds. This is a bug as the
function that it is attaching to is not necessarily the one that the
user wants to attach to.
Instead of blindly picking a function to attach to what is ambiguous,
error with EADDRNOTAVAIL to let the user know that this function is not
unique, and that the user must use another unique function with an
address offset to get to the function they want to attach to.
Link: https://lore.kernel.org/all/20231020104250.9537-2-flaniel@linux.microsoft.com/
Cc: stable@vger.kernel.org
Fixes: 413d37d1eb ("tracing: Add kprobe-based event tracer")
Suggested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Francis Laniel <flaniel@linux.microsoft.com>
Link: https://lore.kernel.org/lkml/20230819101105.b0c104ae4494a7d1f2eea742@kernel.org/
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
[ Sherry: kselftest kprobe_non_uniq_symbol.tc failed on 5.4.y, because of missing
this commit, backport it to 5.4.y. Minor conflicts due to context change, ignore
context change ]
Signed-off-by: Sherry Yang <sherry.yang@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50f813e57601c22b6f26ced3193b9b94d70a2640 upstream.
The simulate_ldr_literal() code always loads a 64-bit quantity, and when
simulating a 32-bit load into a 'W' register, it discards the most
significant 32 bits. For big-endian kernels this means that the relevant
bits are discarded, and the value returned is the the subsequent 32 bits
in memory (i.e. the value at addr + 4).
Additionally, simulate_ldr_literal() and simulate_ldrsw_literal() use a
plain C load, which the compiler may tear or elide (e.g. if the target
is the zero register). Today this doesn't happen to matter, but it may
matter in future if trampoline code uses a LDR (literal) or LDRSW
(literal).
Update simulate_ldr_literal() and simulate_ldrsw_literal() to use an
appropriately-sized READ_ONCE() to perform the access, which avoids
these problems.
Fixes: 39a67d49ba ("arm64: kprobes instruction simulation support")
Cc: stable@vger.kernel.org
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20241008155851.801546-3-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acc450aa07099d071b18174c22a1119c57da8227 upstream.
The simulate_ldr_literal() and simulate_ldrsw_literal() functions are
unsafe to use for uprobes. Both functions were originally written for
use with kprobes, and access memory with plain C accesses. When uprobes
was added, these were reused unmodified even though they cannot safely
access user memory.
There are three key problems:
1) The plain C accesses do not have corresponding extable entries, and
thus if they encounter a fault the kernel will treat these as
unintentional accesses to user memory, resulting in a BUG() which
will kill the kernel thread, and likely lead to further issues (e.g.
lockup or panic()).
2) The plain C accesses are subject to HW PAN and SW PAN, and so when
either is in use, any attempt to simulate an access to user memory
will fault. Thus neither simulate_ldr_literal() nor
simulate_ldrsw_literal() can do anything useful when simulating a
user instruction on any system with HW PAN or SW PAN.
3) The plain C accesses are privileged, as they run in kernel context,
and in practice can access a small range of kernel virtual addresses.
The instructions they simulate have a range of +/-1MiB, and since the
simulated instructions must itself be a user instructions in the
TTBR0 address range, these can address the final 1MiB of the TTBR1
acddress range by wrapping downwards from an address in the first
1MiB of the TTBR0 address range.
In contemporary kernels the last 8MiB of TTBR1 address range is
reserved, and accesses to this will always fault, meaning this is no
worse than (1).
Historically, it was theoretically possible for the linear map or
vmemmap to spill into the final 8MiB of the TTBR1 address range, but
in practice this is extremely unlikely to occur as this would
require either:
* Having enough physical memory to fill the entire linear map all the
way to the final 1MiB of the TTBR1 address range.
* Getting unlucky with KASLR randomization of the linear map such
that the populated region happens to overlap with the last 1MiB of
the TTBR address range.
... and in either case if we were to spill into the final page there
would be larger problems as the final page would alias with error
pointers.
Practically speaking, (1) and (2) are the big issues. Given there have
been no reports of problems since the broken code was introduced, it
appears that no-one is relying on probing these instructions with
uprobes.
Avoid these issues by not allowing uprobes on LDR (literal) and LDRSW
(literal), limiting the use of simulate_ldr_literal() and
simulate_ldrsw_literal() to kprobes. Attempts to place uprobes on LDR
(literal) and LDRSW (literal) will be rejected as
arm_probe_decode_insn() will return INSN_REJECTED. In future we can
consider introducing working uprobes support for these instructions, but
this will require more significant work.
Fixes: 9842ceae9f ("arm64: Add uprobe support")
Cc: stable@vger.kernel.org
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20241008155851.801546-2-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8794ac20a299b647ba9958f6d657051fc51a540 upstream.
As Andrew pointed out, it will make sense that the PTP core
checked timespec64 struct's tv_sec and tv_nsec range before calling
ptp->info->settime64().
As the man manual of clock_settime() said, if tp.tv_sec is negative or
tp.tv_nsec is outside the range [0..999,999,999], it should return EINVAL,
which include dynamic clocks which handles PTP clock, and the condition is
consistent with timespec64_valid(). As Thomas suggested, timespec64_valid()
only check the timespec is valid, but not ensure that the time is
in a valid range, so check it ahead using timespec64_valid_strict()
in pc_clock_settime() and return -EINVAL if not valid.
There are some drivers that use tp->tv_sec and tp->tv_nsec directly to
write registers without validity checks and assume that the higher layer
has checked it, which is dangerous and will benefit from this, such as
hclge_ptp_settime(), igb_ptp_settime_i210(), _rcar_gen4_ptp_settime(),
and some drivers can remove the checks of itself.
Cc: stable@vger.kernel.org
Fixes: 0606f422b4 ("posix clocks: Introduce dynamic clocks")
Acked-by: Richard Cochran <richardcochran@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20241009072302.1754567-2-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 835745a377a4519decd1a36d6b926e369b3033e2 upstream.
The `nouveau_dmem_copy_one` function ensures that the copy push command is
sent to the device firmware but does not track whether it was executed
successfully.
In the case of a copy error (e.g., firmware or hardware failure), the
copy push command will be sent via the firmware channel, and
`nouveau_dmem_copy_one` will likely report success, leading to the
`migrate_to_ram` function returning a dirty HIGH_USER page to the user.
This can result in a security vulnerability, as a HIGH_USER page that may
contain sensitive or corrupted data could be returned to the user.
To prevent this vulnerability, we allocate a zero page. Thus, in case of
an error, a non-dirty (zero) page will be returned to the user.
Fixes: 5be73b6908 ("drm/nouveau/dmem: device memory helpers for SVM")
Signed-off-by: Yonatan Maman <Ymaman@Nvidia.com>
Co-developed-by: Gal Shalom <GalShalom@Nvidia.com>
Signed-off-by: Gal Shalom <GalShalom@Nvidia.com>
Reviewed-by: Ben Skeggs <bskeggs@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241008115943.990286-3-ymaman@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dae9f1187189bc09ff6d25ca97ead711f7e26f9 upstream.
The kernel may crash when deleting a genetlink family if there are still
listeners for that family:
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c000000000c080bc] netlink_update_socket_mc+0x3c/0xc0
LR [c000000000c0f764] __netlink_clear_multicast_users+0x74/0xc0
Call Trace:
__netlink_clear_multicast_users+0x74/0xc0
genl_unregister_family+0xd4/0x2d0
Change the unsafe loop on the list to a safe one, because inside the
loop there is an element removal from this list.
Fixes: b8273570f8 ("genetlink: fix netns vs. netlink table locking (2)")
Cc: stable@vger.kernel.org
Signed-off-by: Anastasia Kovaleva <a.kovaleva@yadro.com>
Reviewed-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20241003104431.12391-1-a.kovaleva@yadro.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d41bff05a61fb539f21e9bf0d39fac77f457434e upstream.
Fix the uninitialized symbol 'rv' in the function ish_fw_xfer_direct_dma
to resolve the following warning from the smatch tool:
drivers/hid/intel-ish-hid/ishtp-fw-loader.c:714 ish_fw_xfer_direct_dma()
error: uninitialized symbol 'rv'.
Initialize 'rv' to 0 to prevent undefined behavior from uninitialized
access.
Cc: stable@vger.kernel.org
Fixes: 91b228107d ("HID: intel-ish-hid: ISH firmware loader client driver")
Signed-off-by: SurajSonawane2415 <surajsonawane0215@gmail.com>
Link: https://patch.msgid.link/20241004075944.44932-1-surajsonawane0215@gmail.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6555cb1cb69db479d0760e392c175ba32426842 upstream.
JieLi tends to use SCSI via USB Mass Storage to implement their own
proprietary commands instead of implementing another USB interface.
Enumerating it as a generic mass storage device will lead to a Hardware
Error sense key get reported.
Ignore this bogus device to prevent appearing a unusable sdX device
file.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241001083407.8336-1-uwu@icenowy.me
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d44238d8254a36249d576c96473269dbe500f5e4 upstream.
I have a ASUS PN51 S mini pc that has two xhci devices. One from AMD,
and other from ASMEDIA. The one from ASMEDIA have problems when resume
from suspend, and keep broken until unplug the power cord. I use this
kernel parameter: xhci-hcd.quirks=128 and then it works ok. I make a
path to reset only the ASMEDIA xhci.
Signed-off-by: Jose Alberto Reguero <jose.alberto.reguero@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240919184202.22249-1-jose.alberto.reguero@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d410e8913f5cffebcca79ffdd596009d4a13a28 upstream.
This commit addresses an issue where events were being processed when
the controller was in a halted state. To fix this issue by stop
processing the events as the event count was considered stale or
invalid when the controller was halted.
Fixes: fc8bb91bc8 ("usb: dwc3: implement runtime PM")
Cc: stable@kernel.org
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240916231813.206-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71c717cd8a2e180126932cc6851ff21c1d04d69a upstream.
This reverts commit 86b20af11e84c26ae3fde4dcc4f490948e3f8035.
This patch leads to passing 0 to simple_read_from_buffer()
as a fifth argument, turning the read method into a nop.
The change is fundamentally flawed, as it breaks the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20241007094004.242122-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87b696209007b7c4ef7bdfe39ea0253404a43770 upstream.
Some Plantronics headset as the below send an unexcept opposite
volume key's HID report for each volume key press after 200ms, like
unecepted Volume Up Key following Volume Down key pressed by user.
This patch adds a quirk to hid-plantronics for these devices, which
will ignore the second unexcepted opposite volume key if it happens
within 220ms from the last one that was handled.
Plantronics EncorePro 500 Series (047f:431e)
Plantronics Blackwire_3325 Series (047f:430c)
The patch was tested on the mentioned model, it shouldn't affect
other models, however, this quirk might be needed for them too.
Auto-repeat (when a key is held pressed) is not affected per test
result.
Cc: stable@vger.kernel.org
Signed-off-by: Wade Wang <wade.wang@hp.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d2b1a1ec9f559d30b724877da4ce592edc41fdc upstream.
A broken device may give an extreme offset like 0xFFF0
and a reasonable length for a fragment. In the sanity
check as formulated now, this will create an integer
overflow, defeating the sanity check. Both offset
and offset + len need to be checked in such a manner
that no overflow can occur.
And those quantities should be unsigned.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruno VERNAY <bruno.vernay@se.com>
Signed-off-by: Hugo SIMELIERE <hsimeliere.opensource@witekio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4afe4183ec77f230851ea139d91e5cf2644c68b upstream.
On a system with CXL memory, the resource tree (/proc/iomem) related to
CXL memory may look like something as follows.
490000000-50fffffff : CXL Window 0
490000000-50fffffff : region0
490000000-50fffffff : dax0.0
490000000-50fffffff : System RAM (kmem)
Because drivers/dax/kmem.c calls add_memory_driver_managed() during
onlining CXL memory, which makes "System RAM (kmem)" a descendant of "CXL
Window X". This confuses region_intersects(), which expects all "System
RAM" resources to be at the top level of iomem_resource. This can lead to
bugs.
For example, when the following command line is executed to write some
memory in CXL memory range via /dev/mem,
$ dd if=data of=/dev/mem bs=$((1 << 10)) seek=$((0x490000000 >> 10)) count=1
dd: error writing '/dev/mem': Bad address
1+0 records in
0+0 records out
0 bytes copied, 0.0283507 s, 0.0 kB/s
the command fails as expected. However, the error code is wrong. It
should be "Operation not permitted" instead of "Bad address". More
seriously, the /dev/mem permission checking in devmem_is_allowed() passes
incorrectly. Although the accessing is prevented later because ioremap()
isn't allowed to map system RAM, it is a potential security issue. During
command executing, the following warning is reported in the kernel log for
calling ioremap() on system RAM.
ioremap on RAM at 0x0000000490000000 - 0x0000000490000fff
WARNING: CPU: 2 PID: 416 at arch/x86/mm/ioremap.c:216 __ioremap_caller.constprop.0+0x131/0x35d
Call Trace:
memremap+0xcb/0x184
xlate_dev_mem_ptr+0x25/0x2f
write_mem+0x94/0xfb
vfs_write+0x128/0x26d
ksys_write+0xac/0xfe
do_syscall_64+0x9a/0xfd
entry_SYSCALL_64_after_hwframe+0x4b/0x53
The details of command execution process are as follows. In the above
resource tree, "System RAM" is a descendant of "CXL Window 0" instead of a
top level resource. So, region_intersects() will report no System RAM
resources in the CXL memory region incorrectly, because it only checks the
top level resources. Consequently, devmem_is_allowed() will return 1
(allow access via /dev/mem) for CXL memory region incorrectly.
Fortunately, ioremap() doesn't allow to map System RAM and reject the
access.
So, region_intersects() needs to be fixed to work correctly with the
resource tree with "System RAM" not at top level as above. To fix it, if
we found a unmatched resource in the top level, we will continue to search
matched resources in its descendant resources. So, we will not miss any
matched resources in resource tree anymore.
In the new implementation, an example resource tree
|------------- "CXL Window 0" ------------|
|-- "System RAM" --|
will behave similar as the following fake resource tree for
region_intersects(, IORESOURCE_SYSTEM_RAM, ),
|-- "System RAM" --||-- "CXL Window 0a" --|
Where "CXL Window 0a" is part of the original "CXL Window 0" that
isn't covered by "System RAM".
Link: https://lkml.kernel.org/r/20240906030713.204292-2-ying.huang@intel.com
Fixes: c221c0b030 ("device-dax: "Hotplug" persistent memory for use like normal RAM")
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Jonathan Cameron <jonathan.cameron@huawei.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Alison Schofield <alison.schofield@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61cc4534b6550997c97a03759ab46b29d44c0017 upstream.
It was found that reading /proc/lockdep after a lockdep splat may
potentially cause an access to freed memory if lockdep_unregister_key()
is called after the splat but before access to /proc/lockdep [1]. This
is due to the fact that graph_lock() call in lockdep_unregister_key()
fails after the clearing of debug_locks by the splat process.
After lockdep_unregister_key() is called, the lock_name may be freed
but the corresponding lock_class structure still have a reference to
it. That invalid memory pointer will then be accessed when /proc/lockdep
is read by a user and a use-after-free (UAF) error will be reported if
KASAN is enabled.
To fix this problem, lockdep_unregister_key() is now modified to always
search for a matching key irrespective of the debug_locks state and
zap the corresponding lock class if a matching one is found.
[1] https://lore.kernel.org/lkml/77f05c15-81b6-bddd-9650-80d5f23fe330@i-love.sakura.ne.jp/
Fixes: 8b39adbee8 ("locking/lockdep: Make lockdep_unregister_key() honor 'debug_locks' again")
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lkml.kernel.org/r/20220103023558.1377055-1-longman@redhat.com
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 248efb2158f1e23750728e92ad9db3ab60c14485 upstream.
A few sites want to assert we own the graph_lock/lockdep_lock, provide
a more conventional lock interface for it with a number of trivial
debug checks.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200313102107.GX12561@hirez.programming.kicks-ass.net
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 10476e6304222ced7df9b3d5fb0a043b3c2a1ad8 upstream.
There were two patterns for lockdep_recursion:
Pattern-A:
if (current->lockdep_recursion)
return
current->lockdep_recursion = 1;
/* do stuff */
current->lockdep_recursion = 0;
Pattern-B:
current->lockdep_recursion++;
/* do stuff */
current->lockdep_recursion--;
But a third pattern has emerged:
Pattern-C:
current->lockdep_recursion = 1;
/* do stuff */
current->lockdep_recursion = 0;
And while this isn't broken per-se, it is highly dangerous because it
doesn't nest properly.
Get rid of all Pattern-C instances and shore up Pattern-A with a
warning.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200313093325.GW12561@hirez.programming.kicks-ass.net
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d5c70e6155d5eae198bade4afeab3c1b15073b6 ]
If hashing fails in sctp_listen_start(), the socket remains in the
LISTENING state, even though it was not added to the hash table.
This can lead to a scenario where a socket appears to be listening
without actually being accessible.
This patch ensures that if the hashing operation fails, the sk_state
is set back to CLOSED before returning an error.
Note that there is no need to undo the autobind operation if hashing
fails, as the bind port can still be used for next listen() call on
the same socket.
Fixes: 76c6d988ae ("sctp: add sock_reuseport for the sock in __sctp_hash_endpoint")
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 099ecf59f05b5f30f42ebac0ab8cb94f9b18c90c ]
sk->sk_max_ack_backlog can be read without any lock being held
at least in TCP/DCCP cases.
We need to use READ_ONCE()/WRITE_ONCE() to avoid load/store tearing
and/or potential KCSAN warnings.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 4d5c70e6155d ("sctp: ensure sk_state is set to CLOSED if hashing fails in sctp_listen_start")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 288efe8606b62d0753ba6722b36ef241877251fd ]
sk->sk_ack_backlog can be read without any lock being held.
We need to use READ_ONCE()/WRITE_ONCE() to avoid load/store tearing
and/or potential KCSAN warnings.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 4d5c70e6155d ("sctp: ensure sk_state is set to CLOSED if hashing fails in sctp_listen_start")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08c8acc9d8f3f70d62dd928571368d5018206490 ]
dcr_map is called in the previous if and therefore needs to be unmapped.
Fixes: 1ff0fcfcb1 ("ibm_newemac: Fix new MAL feature handling")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20241007235711.5714-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bb5a99e1f3fd27accb804aa0443a789161f843c ]
Performing a dummy read ensures that the register write operation is fully
completed, mitigating any potential bus delays that could otherwise impact
the frequency of bitbang usage. E.g., if the JTAG application uses GPIO to
control the JTAG pins (TCK, TMS, TDI, TDO, and TRST), and the application
sets the TCK clock to 1 MHz, the GPIO's high/low transitions will rely on
a delay function to ensure the clock frequency does not exceed 1 MHz.
However, this can lead to rapid toggling of the GPIO because the write
operation is POSTed and does not wait for a bus acknowledgment.
Fixes: 361b79119a ("gpio: Add Aspeed driver")
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20241008081450.1490955-2-billy_tsai@aspeedtech.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
