Enable pin control for qps615 that is necessary to configure
the SDX65 GPIO pins for Wake on LAN support.
Change-Id: Ic5d6d76677e195fc3dec7780d99b5cf50718b8b1
Rename snps,usb2_l1_disable to snps,usb2-gadget-lpm-disable
since driver code for disabling L1 was changed and renamed
to snps,usb2-gadget-lpm-disable in order to align with
upstream.
Change-Id: Ic95baa810ac4da004e83e8a2b25bbfbcd74350df
Add the following changes to support QCN9000 in MTP CPE 1x Pine platform:
1. Add sdxlemur-qcn9000.dtsi to have all QCN9000 related configs.
2. Add memory reservation of 2x52 MB for 2 QCN9000 in
sdxlemur-qcn9000.dtsi but in disabled state.
3. Enable reserved memory for 1 QCN9000 in sdxlemur-mtp-cpe-pine1x.dtsi.
4. Add wifi node with all QCN9000 related configs.
5. Enable pcie0_bus2_dev1_fn0 node with QCN9000 memory configs.
6. Enable GPIO 102 to power on QCN9000.
Change-Id: Ieaa7e6fb567581f6d82ae6edfc2f664adf3ef4cc
sdxlemur-mtp-cpe.dtsi is included in sdxlemur-mtp-cpe.dts as well as
sdxlemur-mtp-cpe-pine1x.dts. WLAN configs present in
sdxlemur-mtp-cpe.dtsi is not applicable for sdxlemur-mtp-cpe-pine1x.dts.
Move all WLAN specific configurations from sdxlemur-mtp-cpe.dtsi to a
new file sdxlemur-mtp-cpe-hsp.dtsi and include this file in
sdxlemur-mtp-cpe.dts only.
Change-Id: I245662cf6b23dcb3b5c5fc5ce2ac61783b801cdc
Rename snps,usb2_l1_disable to snps,usb2-gadget-lpm-disable
since driver code for disabling L1 was changed and renamed
to snps,usb2-gadget-lpm-disable in order to align with
upstream.
Change-Id: I7e41a041a3c563c2a2048968ace3615518ce80de
U1 and U2 are intermediate low power states. If host side and
device side u1 and u2 is supported then host sends a bus reset
signal when usb bus is idle which causes usb disconnect and connect.
This effects many automation runs as adb will be disconencted and
reconnected. Hence, disable u1, u2 on blair to solve this.
Change-Id: I3436b8e758976362919e199ddfad6b1ad659c152
Defines the restore-after-cx-collapse property for MMC driver.
This basically lets the driver know that software needs to save the SDCC
register contents before the CX/XO event and restore the SDCC
register contents after coming out of CX/XO event.
Sdxlemur is not supporting retention of CX PC hence this change is
needed.
Change-Id: Id7808813509fb2ee0ce3469c6e04e787b466994b
Fix proxy-supply for blair regulator nodes while at it also
explicitly enable regulator-resource node for it.
Change-Id: I64bfdad102e00d8e177f7e439223746cf7ed02eb
Add modem level 3 mitigation for bcl level 0 violation
based on latest recommendation for lahaina.
Increase passive delay for bcl thermal zones to delay
clearing bcl mitigation.
Change-Id: I50e7935c53511e5c47826a4252cfebd0e346c1f8
