Due to the requirement from hardware team, long vibration driver
voltage need to decrease to 2.5V avoid 50M camera noise.
Change-Id: I408ea7aea1032c0e093dfbb7136f8efbacc2ce4f
Signed-off-by: zhouwl <zhouwl@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2030286
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Hujun Liao <liaohj@motorola.com>
Submit-Approved: Jira Key
The near-end eye diagram is more critical than the position of the test pattern.
echo 0x1f> /d/162b000.qusb/bias_ctrl2. the eys signal will improve
so bias_ctrl2 change from 0x22 to 0x1f.
Change-Id: I2e422e38f05b4184e2956497599763cf4d9e5659
Signed-off-by: liuyc20 <liuyc20@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2028943
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
According to hardware suggestion, set default duration 70ms,
voltage 3V(keep same voltage for long & short virations).
Change-Id: I7448e9e9a3889b2ce8512905c9445758a766411f
Signed-off-by: zhouwl <zhouwl@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2027673
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Hujun Liao <liaohj@motorola.com>
Submit-Approved: Jira Key
sync with KP bianxh.
cypfq vib 80ms with 3v will cause nosie.
so set vib-dis-short-long-val to 70ms.
if vib time>70ms ,set vib volt to 2.6v.
Change-Id: Ibbcb4f95bb54631d65e3b457178c3c4d86c9f2b7
Signed-off-by: liaohj <liaohj@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2028749
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Wanlong Zhou <zhouwl@motorola.com>
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
Per tinno HW team req, enable this feature to control FM
ELNA module, fix FM signal loss issue of HW design.
Change-Id: I29018dbed21e233ece4d9bb5771843384baf4af1
Signed-off-by: duqiu2 <duqiu2@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2027757
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Xianglong Liao <liaoxl@motorola.com>
Reviewed-by: Ying Xu <xuying9@motorola.com>
Reviewed-by: Tao Sun <suntao2@motorola.com>
Submit-Approved: Jira Key
- Enable ilitek,report_gesture_key for enable report KEY_F1 and KEY_F2
function to make single tap can works properly.
Change-Id: Ib303b536c8e4660efc3b150f431b87ef00d19254
Signed-off-by: wengjun1 <wengjun1@motorola.com>
Reviewed-on: https://gerrit.mot.com/2024904
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
The cypfq's hardware design is differnt with qcom.
GPIO 24 is for Sar not display(panel)
Change-Id: I43c7142fcaa906d2b9d5683ef43c5170dfafa1dc
Signed-off-by: houdz1 <houdz1@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2023741
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
Change the default output voltage through I2C bus at XBL. And store the default
value to EEPROM. So we can nod make I2C operation at kernel.
Only pull up/down gpio to enable/disable regulator.
Change-Id: I2731acde9558632435df0cab9f9cf6829b736c97
Signed-off-by: houdz1 <houdz1@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2020022
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
This requirment is come from STPM.
Auto strategy can swith refresh rate at 90/60/120.
But the UI only have auto/60/120
Change-Id: I6545931a8183768e88e40374e7cbb1b3a50bb9c1
Signed-off-by: houdz1 <houdz1@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2020019
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
We will use hbm-en-gpio to set the max current.
That we can switch hbm and normal mode.
Change-Id: Id60013b61ebf18cae95d6b3448d3e4e24363156c
Signed-off-by: houdz1 <houdz1@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2007870
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
- Since we will only use cypfq in later stages, so add touch dts
for cypfq to prevent confusion.
Change-Id: If3919d1b5652e00b239feb1f3775becb7155d4b1
Signed-off-by: wengjun1 <wengjun1@motorola.com>
Reviewed-on: https://gerrit.mot.com/2014768
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
Vendor's requirment is:
There must be 20ms delay between reset high and download init code.
Change-Id: I29d4000d335c5368eb9e3054a62a73c3e92391cd
Signed-off-by: houdz1 <houdz1@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2011966
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
arm/dt:
Eanble hbm function for vtdr6110c.
Don't set hbm type, then s/w will set it to oled type.
Change-Id: I2bb4d875603c8326c74f0f563197326f96f56433
Signed-off-by: wangyq13 <wangyq13@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2015039
SLTApproved: Slta Waiver
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
- Since ilitek touch will meet esd issue and need to keep int gpio
in pull up state, therefore change dtsi for fixed this issue.
Change-Id: I499da7069160ec7084df6d4ebd27b2d13ca945e7
Signed-off-by: wengjun1 <wengjun1@motorola.com>
Reviewed-on: https://gerrit.mot.com/2010711
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
The need for this modification comes from the hardware team.
Increase wled ovp and ocp, otherwise new board and panel
may trigger ovp fault, cause backlight can't work.
Change-Id: Iabaff8d1cdc91730d0e9f01db14d56f36d397e70
Signed-off-by: houdz1 <houdz1@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2001706
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
As cypfq use pm6375 gpio8 to control charging led,
so enable leds-indicator-pwm.ko to control led.
Change-Id: Ic96865d46872751eacbc36d351d2266b397cfd4e
Signed-off-by: mahj8 <mahj8@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2007933
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Lu Chai <chailu1@motorola.com>
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
Per tinno HW team req, enable this feature to control FM
ELNA module, fix FM signal loss issue of HW design.
Change-Id: Ib565b173990e9c78e55579a0d188893d66b29479
Reviewed-on: https://gerrit.mot.com/2007695
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
At "holi-sde-display-mtp-pm6125.dtsi", gpio24 is used to enable
avdd for panel.
For cypfq, gpio24 is for sar.
Change-Id: Id291165d60aee4a05bfd7f952e3ff4fa00d00a0f
Signed-off-by: houdz1 <houdz1@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2005094
SME-Granted: SME Approvals Granted
Tested-by: Jira Key
SLTApproved: Slta Waiver
Reviewed-by: Yeqing Wang <wangyq13@motorola.com>
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
cypfq in on SM4350 Pro with PM6125.
Config the thermal zones by HW schematic.
Change-Id: Ie09c43c73999ae8bd226d8a8cc25b23bab53be4a
Reviewed-on: https://gerrit.mot.com/2003206
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Lu Chai <chailu1@motorola.com>
Reviewed-by: Xiaojun Ji <jixj@motorola.com>
Reviewed-by: Huosheng Liao <liaohs@motorola.com>
Submit-Approved: Jira Key
Qcom enables smb1394 in <holi-mtp-pm7250b.dtsi>,
i2c addr is 0x34, probe on qupv3_se10_i2c, it is
same as aw882xx. Corfu doesn't use this smb1394,
disable it.
Change-Id: I944d6dcaa4a0793d7b2048b30c6ad90311d1ae79
Signed-off-by: zhouwl <zhouwl@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2003691
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Hujun Liao <liaohj@motorola.com>
Submit-Approved: Jira Key
qcom new version rebase.
qcom smb1394 use the same i2c & addr.
it is not useful for cypfq.disable it.
Change-Id: I48b4e3965fb2ffde98e976ad5d885e278343a454
Signed-off-by: liaohj <liaohj@lenovo.com>
Reviewed-on: https://gerrit.mot.com/2003669
SME-Granted: SME Approvals Granted
SLTApproved: Slta Waiver
Tested-by: Jira Key
Reviewed-by: Wanlong Zhou <zhouwl@motorola.com>
Reviewed-by: Yuesheng Huang <huangys@motorola.com>
Submit-Approved: Jira Key
