When lahaina-rumi is compiled as a separate overlay, it does
not explicitly include the definition of the &soc node. Without
the #address-cells and #size-cells specifiers, the compiler uses
default values of 2 and 1, respectively, which results in the
following warnings when compiling lahaina-rumi-overlay.dtb:
Warning (reg_format): "reg" property in
/fragment@15/__overlay__/usb_emu_phy@a720000 has invalid length (8
bytes) (#address-cells == 2, #size-cells == 1) Warning
(avoid_default_addr_size): Relying on default #address-cells value for
/fragment@15/__overlay__/usb_emu_phy@a720000
Warning (avoid_default_addr_size): Relying on default #size-cells
value for /fragment@15/__overlay__/usb_emu_phy@a720000
As the &soc node is referenced here only for the purpose of adding
a new child node, usb_emu_phy, address the warnings by explicitly
defining the {address,size}-cells values.
Change-Id: I8b5ebcd53c060eeea3c55bf9fb8e55093e7862f2
QTI battery glink debug device helps to get logs and debug
information by communicating with charger firmware running on the
remote subsystem (e.g. DSP) over PMIC Glink.
Change-Id: I3a894b40bbbb67dbe26ad683cfabe330bf7e3d69
Swr dmic powers up using standalone mic bias widget.
Update the device tree routing to replace analog mic
bias widget with the standalone mic bias widget.
Change-Id: If8e74283f02a5c1bc173720778d6f03649264606
Triggering enable and disable of swr dmic power supply
mic bias using widget name is more straight forward
than using mic bias number. Replace the number with
widget name instead.
Change-Id: Ie56ee41926249a044ab0f1bc197235c47803e46d
Replace mic bias number with widget string property to
swr mic device tree documentation for Lahaina target.
Change-Id: Ic14ae2cb66867c60a2a8ccf24b26446df6ae673b
Add interconnect bcm voter devices for display specific RSC
and phandles for interconnect NoC devies to target display RSC.
Change-Id: I72b310ab0cc7a3f673452e6b333f5a428eb80f4b
Add proxy consumer configurations for PM8350 LDO 5 and LDO 6
which ensure that these regulators are kept enabled in high
power mode until all consumers have a chance to make their own
requests.
Change-Id: Ia159e39418ce67585f6c81deeaf4ee3b1c52fcf7
On Lahaina,
- GPIO_65 is mapped to BT_EN pin on Hastings prime.
- AON and DIG on Hastings prime is powered from S11B
- RFA1 on hastings prime is powered from S1C
- RFA2 on hastings prime is powered from S12B
- Add bt_en_active in pinctrl so as to make BT_EN
pin controllable
- Hastings prime has got logical address changed
which acts as a slimbus slave. Change dedicated logical
address for HSP.
Change-Id: I7560770ba6829ba67c285b2be5d938ffffe839b7
Add regmaps for MMIO registers for QoS configurations and required
clocks to access certain QoS registers.
Change-Id: I28814e6a7b8808500005f3f785e7ee8a491189de
Flash LED driver provides support for the clients to turn ON/OFF LED
channels in different modes (flash/torch) individually or as a group.
Add the bindings necessary to describe it.
Change-Id: Id9eebbeaef5933477bc3dc5db8d674cab059e5d0
Add DT bindings for QTI battery charger which gets and sets
power supply properties by communicating with charger firmware
running on the remote subsystem (e.g. DSP) over PMIC Glink.
Change-Id: I8e3aedfb70c627807388db3c449c283f35ecfd59
The bootloaders are bypassing the SMMU for UFS already, and doing
the same from the kernel would be redundant. Hence, remove the
properties to bypass SMMU.
Change-Id: Ida9e7d68ffa9f97a3e6f07d974fa842ef794852f
