Add qosgen shaping configuration setup. These parameters
will be tuned for every chipset along with other QoS
settings.
CRs-Fixed: 2787956
Change-Id: I2659192bd23f7f558554e18768e96020b929a145
Signed-off-by: Chandan Kumar Jha <cjha@codeaurora.org>
Clear registers hold the programmed values unless explicitly set to zero.
This can cause problems in cases where a global clear is issued which
encompasses the registers for which clear mask was set in a different
instance of IRQ controller. We should not wait for the next IRQ to clear
the undesired bits in clear register. This change makes sure that the
actions of a particular IRQ controller do not affect the other. Write
zeros explicitly to clear registers corresponding to status registers
after global clear is issued in IRQ handler.
CRs-Fixed: 2775499
Change-Id: Ic57302e5862d9453a94c4e8f470215dacb8978ec
Signed-off-by: Mukund Madhusudan Atre <matre@codeaurora.org>
During first CCI HW initialization, CCI HW global reset has to be called.
CRs-Fixed: 2782553
Change-Id: Ifc02f512859932636c79b0bfed1f60e7c0626cee
Signed-off-by: Anil Kumar Kanakanti <akanakan@codeaurora.org>
EPD support is configured as a part of config blob. Currently global
reset is invoked after CSID is configured and as a part of that
epd support attributre gets reset. This cause CPHY_EOT_RECEPTION
error from CSID. This change removes reset part of epd supported
attribute to continue with the expected opertion set during
configuration of CSID. Also, set this attribute to zero by default
at probe time to make sure epd is not supported.
CRs-Fixed: 2775508
Change-Id: I0f49f952d2156d92eb0fb1813951a325b63e60b0
Signed-off-by: Jigarkumar Zala <jzala@codeaurora.org>
Tfe hardware support the last consumed buf address.
Request port buf done verified with last consumed buffer
Address. Buf done irq delays can be handled through
last consumed address verification.
CRs-Fixed: 2784348
Change-Id: I4d629da44cf6f1b7755c7785eac11f72384c78c7
Signed-off-by: Ravikishore Pampana <rpampana@codeaurora.org>
Make sure we perform the necessary unlock operations before we return
on an invalid HFI state.
CRs-Fixed: 2783934
Change-Id: I7c611fb98d245952f2f4e9a57dc5fcb249572a40
Signed-off-by: Fernando Pacheco <fpacheco@codeaurora.org>
This change updates the order of error notification, in case
the UMD already receive the error notification and power down
the isp, then the following register dump may meet problem.
This change also add lock protection for csid cmd processing,
in case the csid has released before processing the cmd.
CRs-Fixed: 2783264
Change-Id: I7399d819d1cdadb96b6824cdb4b53aa0167e527b
Signed-off-by: Depeng Shao <depengs@codeaurora.org>
Process tfe page faults based on the pid and mid values.
When page fault happen kernel api gives the pid and mid value,
From pid and mid values TFE hw and tfe port that caused the
Page fault can be find. Added support for this in the tfe driver.
Based on the Pid and Mid values, get the HW id and port ids,
go through all context which has this hw id and port id and log
the data. Once context id is identified, log the acquire data and
last consumed client address details. Dump the hw register data
in the given buffer. Send the smmu page fault event through
v4l2 queue to user.
CRs-Fixed: 2775154
Change-Id: Iafaa7d1283ea0b836c223ed1fe6c419b0ac50c15
Signed-off-by: Ravikishore Pampana <rpampana@codeaurora.org>
Currently pinctrl is handled together regardless of pinctrl
is requested for the active/suspend state. This change adds
the per pinctrl handling when pinctrl gpio is shared among
multiple slaves. Also remove mclk specific logic as this
change will handle it at gpio/pinctrl level.
CRs-Fixed: 2758167
Change-Id: I4fa028d3eee80e056a74324a420c08967cbf6c5f
Signed-off-by: Jigarkumar Zala <jzala@codeaurora.org>
During first CCI HW initialization, CCI HW global reset has to be called.
Removed is_initialized removed, as it can be controlled through
master_active_slave ref count to verify there is any active slave or not.
CRs-Fixed: 2782553
Change-Id: Id845bfc936b976e160231ed3a0acbc951c32ad7f
Signed-off-by: Anil Kumar Kanakanti <akanakan@codeaurora.org>
Reduced maximum no of requests per context from 20 to 8
in isp driver.
CRs-Fixed: 2720238
Change-Id: If557b190fe94af72cc6fb28f36c3e1f6189218a5
Signed-off-by: Shravya Samala <shravyas@codeaurora.org>
Fix the order of imports for to resolve cam_sync
typedef for kernel CFI.
CRs-Fixed: 2772200
Change-Id: I4e5e642e6b45412904585aaa68c0ef77fedeee2d
Signed-off-by: Karthik Jayakumar <kjayakum@codeaurora.org>
Increase max bl limit for OPE to 24 to support maximum
48 stripes.
CRs-Fixed: 2761455
Change-Id: I961be1344fac0084649df321225e94a50d4e5a98
Signed-off-by: Rishabh Jain <risjai@codeaurora.org>
Modify the sof monotonic boot timestamp logic. Boot time
stamp difference between two frames should not change,
it should be same as qtime csid time stamp difference.
So modified logic to give proper boot time stamp with no
difference in the successive frames, the difference of sof
time stamp taken from qtime stamp value.
Delayed IRQ handling can lead to torn read of timestamp
register (LSB from nth frame and MSB from n+1th frame).
This change tries to detect torn read cases and corrects
timestamp close to the actual value.
CRs-Fixed: 2688271
Change-Id: I1dc75629887cfcf971d51a7dae6ea28624d272f1
Signed-off-by: Ravikishore Pampana <rpampana@codeaurora.org>
Remove following unused CCI and CPHY flags.
CRs-Fixed: 2709537
Change-Id: I7a936733da75c71877ae52cfae9ddd358775c305
Signed-off-by: Jigar Agrawal <jigar@codeaurora.org>
This change takes care of a race which we see when we halt master
csid immediately and slave csid halt to follow. In some scenarios
after master csid halt, slave gives violation errors.
With this change we are first changing the mode of slave to master
then issue halt commands to both master and slave.
CRs-Fixed: 2773668
Change-Id: Iab7baa41a69b2e4e0a658c7abac29d2dcb80c289
Signed-off-by: Ayush Kumar <ayushkr@codeaurora.org>
When workqueue is congested, CRM may apply same
request to device which will trigger recovery
due to apply fails. This change prevent CRM
triggering recovery if the time interval of
continuous applying req less than 5ms.
CRs-Fixed: 2775372
Change-Id: I45c2ed76334b1bbf4547bbf21f90cf0a6c169323
Signed-off-by: Depeng Shao <depengs@codeaurora.org>
Drop references to A5 within the debugfs entries so that they
may be reused with other processors.
CRs-Fixed: 2722486
Change-Id: I2680a98dd3d38906e616712da3d6e2835ebb9a85
Signed-off-by: Fernando Pacheco <fpacheco@codeaurora.org>
The A5 references sprinkled throughout the hw manager will no
longer make sesne within the context of two possible processors.
We will instead prefer the more generic "icp" term to reference
the processor in use e.g. icp_dev instead of a5_dev.
Note that some references to A5 remain and will be cleaned up
when LX7 is introduced.
CRs-Fixed: 2722486
Change-Id: I9af73cc2af27a2aed2f4d7baaead89a20442e9ed
Signed-off-by: Fernando Pacheco <fpacheco@codeaurora.org>
The HFI interface registers will have a different base address
on the LX7 processor. We can utilize the newly added HFI ops to
abstract the calculation of the address by kicking that info out
to the device interface. The HFI register definitions have been
tweaked to support offsets based on the calculated addresses.
CRs-Fixed: 2722486
Change-Id: I93b9b2827ec0820eaac6ee2e6a611363b96a3223
Signed-off-by: Fernando Pacheco <fpacheco@codeaurora.org>
If bubble recovery is disabled, IFE driver should continue
to notify that epoch to CRM as opposed to dropping that frame
in IFE. In case of sHDR if bubble recovery is disabled and IFE
does not notify the epoch at which bubble was detected it will lead
to a trigger count mismatch in CRM.
CRs-Fixed: 2768309
Change-Id: I311ce80857a905496c633708a5f4ee2391679037
Signed-off-by: Karthik Anantha Ram <kartanan@codeaurora.org>
In Some targets number of use cases are 7 and it was an issue during
setting TURBO clock level.
Changed the validation from number of client usecase to MAX supported
clock level.
CRs-Fixed: 2571273
Change-Id: I05cd06ff11c2c43eb4b70d69314e04055894c5fc
Signed-off-by: Chandan Kumar Jha <cjha@codeaurora.org>
CCI register dump is only enable when dump flag is defined. Remove
this flag and add control via debugfs entry. This change helps
debugfs entry to control cci device individually on the fly for
debugging rather than to rebuild.
CRs-Fixed: 2692379
Change-Id: Ic13dc903e861e7c49bf3b375a66b96bfbe5d9c70
Signed-off-by: shiwgupt <shiwgupt@codeaurora.org>
