Auto RC clock calibration is used as default configuration. When playing
FIFO streaming data, manual RC clock calibration is used for adjusting
the FIFO pattern based on the detected LRA frequency. Restore back to use
auto RC clock calibration after FIFO pattern is played.
Change-Id: I335552cfeafe559aa35a76bf6aa218a92b62d3db
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Check INT_RT_STS in FIFO empty IRQ handler and ignore the interrupt
if FIFO_EMPTY real time status bit is not set.
Change-Id: I7a276fa1d8c79d530fc26f74263e0608096a99f8
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Use 2's complement data format for driving pattern waveform because
the pattern/FIFO samples used in the driver are all having unsigned
data type.
Change-Id: Ib0f7c1c7fe272068177237821debbd3cc1ad4ec8
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
PM8350B has a variant which only supports haptics with Vmax up to 5V.
Detect this variant and update Vmax settings accordingly to make sure
the gain setting change can be correctly reflected.
Change-Id: I916fba21d8a441b9e95edeef5af715d451ba70cf
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
As of commit <a5f1397e4b> ("Revert "BACKPORT: tracing: Remove
unnecessary DEBUG_FS dependency""), DEBUG_FS was selected by TRACING.
Remove DEBUG_FS dependency in Tracing kconfig. CONFIG_DEBUG_FS will now
be enabled in QGKI config. Also update the whitelist and abi snapshot.
Change-Id: I8c9e9fb6b97173d6e62f6090712642f18d842888
Signed-off-by: Prakruthi Deepak Heragu <pheragu@codeaurora.org>
Enable TOS and DSCP target support for Holi target
Change-Id: Ib7fbe8442007160f8158f41ba29613fdf1b7fcd1
Signed-off-by: Sharath Chandra Vurukala <sharathv@codeaurora.org>
EUD HUB functionality is relevant into USB device mode only. Hence when
using USB host mode, continue performing reset and initialization
functionality with HSPHY even though EUD is enable. If EUD is enable
while starting host mode, re-enable EUD whie exiting host mode.
Change-Id: Ifc2a105d8a02511dd2fc58be5fbc788d46546ba0
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Currently usb speed override functionality doesn't work as expected
when usb role switch based notification is used. Hence move usb speed
override functionality out side edev check within dwc3_resume_work()
API. Also update maximum_speed as max hw supported speed out side
edev check.
Change-Id: I69b066721490277b77333d2caf820b6c87703501
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
cpu_isolated_mask can only be used when SCHED_WALT is enabled. The
addition of the cpu_isolated_mask causes ABI to break. Thus, compile
references to cpu_isolated_mask only when SCHED_WALT is enabled.
Change-Id: I0982f6431abca807168dbabc4aca74771819565c
Signed-off-by: Elliot Berman <eberman@codeaurora.org>
The FORCE_MEM_CORE_ON bits default to 0 and this is fine for most use
cases. However, USB needs FORCE_MEM_CORE_ON=1 to properly retain its
memories when USB APM switches from CX to MX. This can't just be a
one-time setting since the FORCE_MEM_CORE_ON bits need to be set/cleared
upon USB cable connect/disconnect for power optimization. Add fake
clocks to allow the USB client to control them.
Change-Id: Ic7aac944feaa6a956a8892e0cf1f4dd465659302
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Add clock bindings to control the USB FORCE_MEM_CORE_ON bits.
Change-Id: I406e98e1be5b4d6702636c3bfdf738ae9ff12198
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
